Listing the YRC1000 error codes in the range from 4000 to 4999. These are minor alarms.
YAS5.02
Listing the YRC1000 error codes in the range from 4000 to 4999. These are minor alarms.
YAS5.02
Description:
Sub Code: Tool number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the tool file in maintenance mode, and then load the tool file saved in the external memory device.
Description:
Sub Code: User coordinate number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the user coordinates file in maintenance mode, and then load the user coordinates file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the servo monitor signal file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the servo monitor signal file in maintenance mode, and then load the servo monitor signal file saved in the external memory device.
Description:
Sub Code: Page number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the weaving condition file in maintenance mode, and then load the weaving condition file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the home positioning file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the home positioning file in maintenance mode, and then load the home positioning file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the second home position file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the second home positioning file in maintenance mode, and then load the second home positioning file saved in the external memory device.
Description:
Sub Code: Page number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the arc welding Power Source condition file in maintenance mode, and then load the arc welding Power Source condition file saved in the external memory device.
Description:
Sub Code: Page number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the arc start condition file in maintenance mode, and then load the arc start condition file saved in the external memory device.
Description:
Sub Code: Page number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the arc end condition file in maintenance mode, and then load the arc end condition file saved in the external memory device.
Description:
Sub Code: Page number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the arc auxiliary condition file in maintenance mode, and then load the arc auxiliary condition file saved in the external memory device.
Description:
Sub Code: Page number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the COM-ARC condition file in maintenance mode, and then load the COM-ARC condition file saved in the external memory device.
Description:
The memory for the tool file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the tool file in maintenance mode, and then load the tool file saved in the external memory device.
Description:
The memory for the user coordinate file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the user coordinate file in maintenance mode, and then load the user coordinate file saved in the external memory device.
Description:
The memory for the robot calibration file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the robot calibration file in maintenance mode, and then load the robot calibration file saved in the external memory device.
Description:
The memory for the conveyor calibration file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the conveyor calibration file in maintenance mode, and then load the conveyor calibration file saved in the external memory device.
Description:
The memory for the liner up file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the liner up file in maintenance mode, and then load the liner up file saved in the external memory device.
Description:
The memory for the gun detail setting file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the gun detail setting file in maintenance mode, and then load the gun detail setting file saved in the external memory device.
Description:
The memory for the spot management file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the spot management file in maintenance mode, and then load the spot management file saved in the external memory device.
Description:
The memory for the spot welder I/F file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the spot welder I/F file in maintenance mode, and then load the spot welder I/F file saved in the external memory device.
Description:
The memory for the manual press condition file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the manual press condition file in maintenance mode, and then load the manual press condition file saved in the external memory device.
Description:
The memory for the wear detection base position file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the wear detection base position file in maintenance mode, and then load the wear detection base position file saved in the external memory device.
Description:
The memory for the learning control I/O allocation file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the learning control I/O allocation file in maintenance mode, and then load the learning control I/O allocation file saved in the external memory device.
Description:
The memory for the paint system file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the paint system file in maintenance mode, and then load the paint system file saved in the external memory device.
Description:
The memory for the paint special file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the paint special file in maintenance mode, and then load the paint special file saved in the external memory device.
Description:
The memory for the paint condition file(gun1) is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the paint condition file in maintenance mode, and then load the paint condition file saved in the external memory device.
Description:
The memory for the paint condition file(gun2) is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the paint condition file in maintenance mode, and then load the paint condition file saved in the external memory device.
Description:
The memory for the paint condition file(gun3) is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the paint condition file in maintenance mode, and then load the paint condition file saved in the external memory device.
Description:
The memory for the paint condition file(gun4) is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the paint condition file in maintenance mode, and then load the paint condition file saved in the external memory device.
Description:
The memory for the paint calibration set file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the paint calibration set file in maintenance mode, and then load the paint calibration set file saved in the external memory device.
Description:
The memory for the paint time chart set file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the paint time chart set file in maintenance mode, and then load the paint time chart set file saved in the external memory device.
Description:
The memory for the paint time chart file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the paint time chart file in maintenance mode, and then load the paint time chart file saved in the external memory device.
Description:
The memory for the paint data set file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the paint data set file in maintenance mode, and then load the paint data set file saved in the external memory device.
Description:
The memory for the io paint condition output file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the io paint condition output file in maintenance mode, and then load the io paint condition output file saved in the external memory device.
Description:
The memory for the IOSPDCTRL setup file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the IOSPDCTRL setup file in maintenance mode, and then load the IOSPDCTRL setup file saved in the external memory device.
Description:
The memory for the SETTM SETUP file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the SETTM SETUP in maintenance mode, and then load the SETTM SETUP saved in the external memory device.
Description:
The memory for the TIMER VARIABLE NAME file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the TIMER VARIABLE NAME file in maintenance mode, and then load the TIMER VARIABLE NAME file saved in the external memory device.
Description:
The memory for the takumi path correct file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the takumi path correct file in maintenance mode, and then load the takumi path correct file saved in the external memory device.
Description:
The memory for the USER GROUP INPUT file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the USER GROUP INPUT file in maintenance mode, and then load the USER GROUP INPUT file saved in the external memory device.
Description:
The memory for the USER GROUP OUTPUT file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the USER GROUP OUTPUT file in maintenance mode, and then load the USER GROUP OUTPUT file saved in the external memory device.
Description:
The memory for the SENSPS SETTING DATA is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the SENSPS SETTING DATA in maintenance mode, and then load the SENSPS SETTING DATA saved in the external memory device.
Description:
The memory for the USER ANALOG INPUT file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the USER ANALOG INPUT file in maintenance mode, and then load the USER ANALOG INPUT file saved in the external memory device.
Description:
The memory for the USER ANALOG OUTPUT file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the USER ANALOG OUTPUT file in maintenance mode, and then load the USER ANALOG OUTPUT file saved in the external memory device.
Description:
The memory for the F-SAFETY SIGNAL ALLOC file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the USER ANALOG OUTPUT file in maintenance mode, and then load the USER ANALOG OUTPUT file saved in the external memory device.
Description:
The memory for the SLC EXT. SIGNAL ALLOC file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the safety logic file in maintenance mode, and then load the safety logic file saved in the external memory device.
Description:
The memory for the safety logic comment file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the safety logic file in maintenance mode, and then load the safety logic file saved in the external memory device.
Description:
The memory for the timer set file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the safety logic file in maintenance mode, and then load the safety logic file saved in the external memory device.
Description:
The memory for the PAINT RECOVERY file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the PAINT RECOVERY file in maintenance mode, and then load the PAINT RECOVERY file saved in the external memory device.
Description:
The memory for the reducer remain time file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the reducer remain time file in maintenance mode, and then load the reducer remain time file saved in the external memory device.
Description:
The memory for the safety logic signal display setup file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the safety logic file in maintenance mode, and then load the safety logic file saved in the external memory device.
Description:
The memory for the F-SAFETY SIGNAL ALLOC file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the safety logic file in maintenance mode, and then load the safety logic file saved in the external memory device.
Description:
The memory for the SPECIFIC INPUT COMMENT SET file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the safety logic file in maintenance mode, and then load the safety logic file saved in the external memory device.
Description:
The memory for the operating time database is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the operating time database in maintenance mode, and then load the operating time database saved in the external memory device.
Description:
The memory for the operating time database is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the operating time database in maintenance mode, and then load the operating time database saved in the external memory device.
Description:
The memory for the operating time database is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the operating time database in maintenance mode, and then load the operating time database saved in the external memory device.
Description:
The memory for the Job Monitor is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the operating time database in maintenance mode, and then load the operating time database saved in the external memory device.
Description:
The memory for the STEP DIAGNOSIS file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the STEP DIAGNOSIS file in maintenance mode, and then load the STEP DIAGNOSIS saved in the external memory device.
Description:
The memory for the ROBOT MONITOR file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the ROBOT MONITOR in maintenance mode, and then load the ROBOT MONITOR file saved in the external memory device.
Description:
The memory for the ROBOT ARRANGEMENT SETUP file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the ROBOT ARRANGEMENT SETUP in maintenance mode, and then load the ROBOT ARRANGEMENT SETUP file saved in the external memory device.
Description:
The memory for the ROBOT RANGE DISP DATA is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the ROBOT RANGE DISP DATA in maintenance mode, and then set the ROBOT RANGE DISP DATA.
Description:
The memory for the servo power time is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the servo power time database in maintenance mode, and then load the servo power time database saved in the external memory device.
Description:
The memory for the SYNCHRO WELDING PARAMETER is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the SYNCHRO WELDING PARAMETER in maintenance mode, and then load the SYNCHRO WELDING PARAMETER saved in the external memory device.
Description:
The memory for the safety logic file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the safety logic file in maintenance mode, and then load the safety logic file saved in the external memory device.
Description:
The memory for the safety logic comment file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the safety logic file in maintenance mode, and then load the safety logic file saved in the external memory device.
Description:
The memory for the material filling setup file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the material filling setup file in maintenance mode, and then load the material filling setup file saved in the external memory device.
Description:
The memory for the pressure sensor monitor file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the pressure sensor monitor file in maintenance mode, and then load the pressure sensor monitor file saved in the external memory device.
Description:
The memory for the manual purge setup file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the manual purge setup file in maintenance mode, and then load the manual purge setup file saved in the external memory device.
Description:
The memory for the bonding condition file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the bonding condition file in maintenance mode, and then load the bonding condition file saved in the external memory device.
Description:
The memory for the pressure/volt table file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the pressure/volt table file in maintenance mode, and then load the pressure/volt table file saved in the external memory device.
Description:
The memory for the pressure/temp monitor file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the pressure/temp monitor file in maintenance mode, and then load the pressure/temp monitor file saved in the external memory device.
Description:
The memory for the tool confirmation file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the tool file in maintenance mode, and then load the tool file saved in the external memory device.
Description:
The memory for the welding process definition file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the welding process definition file in maintenance mode, and then load the welding process definition file saved in the external memory device.
Description:
Sub Code: Condition file number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the link servo float condition file in maintenance mode, and then load the link servo float condition file saved in the external memory device.
Description:
Sub Code: Condition file number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the linear servo float condition file in maintenance mode, and then load the linear servo float condition file saved in the external memory device.
Description:
Sub Code: Page number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the file for calibration between manipulators in maintenance mode, and then load the file for calibration between manipulators saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the Power Source user definition file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the Power Source user definition file in maintenance mode, and then load the Power Source user definition file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the ladder program file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the ladder program file in maintenance mode, and then load the ladder program file saved in the external memory device.
Description:
Sub Code: Page number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the cutting condition file in maintenance mode, and then load the cutting condition file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the work home position file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the work home position file in maintenance mode, and then load the work home position file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the conveyor condition file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the conveyor condition file in maintenance mode, and then load the conveyor condition file saved in the external memory device.
Description:
Sub Code: Page number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the paint special file in maintenance mode, and then load the paint special file saved in the external memory device.
Description:
Sub Code: Page number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the paint condition file in maintenance mode, and then load the paint condition file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the wrist weaving amplitude file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the wrist weaving amplitude file in maintenance mode, and then load the wrist weaving amplitude file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the interrupt job file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the interrupt job file in maintenance mode, and then load the interrupt job file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the sensor monitoring condition file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the sensor monitoring condition file in maintenance mode, and then load the sensor monitoring condition file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the press condition file in maintenance mode, and then load the press condition file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the gun condition file in maintenance mode, and then load the gun condition file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the spot welding gun condition file in maintenance mode, and then load the spot welding gun condition file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the gun pressure file in maintenance mode, and then load the gun pressure file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the anticipation outputs (OT) file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the anticipation output (OT) file in maintenance mode, and then load the anticipation output (OT) file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the anticipation outputs (OG) file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the anticipation output (OG) file in maintenance mode, and then load the anticipation output (OG) file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the wear amount file in maintenance mode, and then load the wear amount file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the FULL/SHORT OPEN position setting file in maintenance mode, and then load the FULL/SHORT OPEN position setting file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the dry-spotting pressure file in maintenance mode, and then load the dry-spotting pressure file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the form cut file in maintenance mode, and then load the form cut file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the shock level file in maintenance mode, and then load the shock level file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the spot I/O allocation file in maintenance mode, and then load the spot I/O allocation file saved in the external memory device.
Description:
Sub Code: Page number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the vision condition file in maintenance mode, and then load the vision condition file saved in the external memory device.
Description:
Sub Code: Page number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the vision calibration file in maintenance mode, and then load the vision calibration file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the welding pulse condition file in maintenance mode, and then load the welding pulse condition file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the welding pulse selection file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the welding pulse selection file in maintenance mode, and then load the welding pulse selection file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the conveyor calibration file in maintenance mode, and then load the conveyor calibration file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the macro definition file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the macro definition file in maintenance mode, and then load the macro definition file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the sealer gun characteristics file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the sealer gun characteristics file in maintenance mode, and then load the sealer gun characteristics file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the painting amount correction file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the painting amount correction file in maintenance mode, and then load the painting amount correction file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the axis motion I/O allocation file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the axis motion I/O allocation file in maintenance mode, and then load the axis motion I/O allocation file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the gun characteristics auxiliary file in maintenance mode, and then load the gun characteristics auxiliary file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the tool interference file in maintenance mode, and then load the tool interference file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the painting system setting file in maintenance mode, and then load the painting system setting file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the painting device characteristics file in maintenance mode, and then load the painting device characteristics file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the painting CCV file in maintenance mode, and then load the painting CCV file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the painting filling file in maintenance mode, and then load the painting filling file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the EVB gun condition file in maintenance mode, and then load the EVB gun condition file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the EVB turbine condition file in maintenance mode, and then load the EVB turbine condition file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the EVB paint condition file in maintenance mode, and then load the EVB paint condition file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the clearance file in maintenance mode, and then load the clearance file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the gauging sensor condition file in maintenance mode, and then load the gauging sensor condition file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the linear scale condition file in maintenance mode, and then load the linear scale condition file saved in the external memory device.
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the conveyor condition auxiliary file in maintenance mode, and then load the conveyor condition auxiliary file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the weaving synchronizing welding condition file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the weaving synchronizing welding condition file in maintenance mode, and then load the weaving synchronizing welding condition file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the I/F panel file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the I/F panel file in maintenance mode, and then load the I/F panel file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the palletizing condition file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the palletize condition file in maintenance mode, and then load the palletize condition file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the laser tracking welding start file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the laser tracking welding start file in maintenance mode, and then load the laser tracking welding start file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the laser tracking welding end file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the laser tracking welding end file in maintenance mode, and then load the laser tracking welding end file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the laser tracking track start file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the laser tracking track start file in maintenance mode, and then load the laser tracking track start file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the laser tracking welding set file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the laser tracking welding set file in maintenance mode, and then load the laser tracking welding set file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the laser tracking track set file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the laser tracking track set file in maintenance mode, and then load the laser tracking track set file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the condition file of corresponding to laser tracking gap is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the condition file of corresponding to laser tracking gap in maintenance mode, and then load the condition file of corresponding to laser tracking gap saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the memory play file for laser tracking DC is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the memory play file for laser tracking DC in maintenance mode, and then load the memory play file for laser tracking DC saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the mutual wait set file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the mutual wait set file in maintenance mode, and then load the mutual wait set file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the interference predict file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the mutual wait set file in maintenance mode, and then load the interference predict file saved in the external memory device.
Content:
YRC1000 has detected the possibility of interference between manipulators.
Remedy:
(1) Reset the alarm.
(2) Pull the manipulators away each other.
(3) If this alarm occurred during test run or playback operation, change the teaching points.
Description:
SubCode
0000_0000_0000_0010:YRC1000 received an error response from the interference predict server.
0001_0000_0000_0001:No response for the interference check start request was returned from the interference predict server.
0001_0000_0000_0010:No response for the current position acquisition request was returned from the interference predict server.
0001_0000_0000_0011:YRC1000 received an error response for the interference check start request from the interference predict server.
Remedy:
(1) Reset the alarm.
(2) Check the connection between interference predict server and YRC1000.
Description:
SubCode
0000_0000_0000_0001:No response was returned from the mutual wait target.
0000_0000_0000_0010:An error occurred in the communication with the mutual wait target during the execution of RSYNC.
0000_0000_0000_0110:The setting of the mutual wait target was changed during the execution of RSYNC.
0000_0000_0001_0000:The mutual wait manipulator No. of the RSYNC is abnormal.
0000_0000_0010_0000:RSYNC was doubly executed.
0000_0000_0101_0000:An illegal notification was received from mutual wait target.
0000_0000_0111_0000:RSYNC was executed for the disconnected robot.
Remedy:
SubCode
0000_0000_0000_0001
(1) Reset the alarm.
(2) Check the contents of the mutual wait setting file.
(3) Check the network setting of the mutual wait target.
Content:
An error was detected at memory check.
The memory for the interference history file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the mutual wait set file in maintenance mode, and then load the interference history file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the safety set file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the safety logic file in maintenance mode, and then load the safety logic file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the timer file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the safety logic file in maintenance mode, and then load the safety logic file saved in the external memory device.
Content:
An error was detected at memory check.
The memory for the safety logic file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the safety logic file in maintenance mode, and then load the safety logic file saved in the external memory device.
Description:
Sub Code: Station address of I/O module
Remedy:
Replace the fuse on the General I/O unit of the corresponding station.
Description:
Sub Code: Station address of I/O module
Remedy:
Replace the General I/O unit of the corresponding station.
Description:
Sub Code: Station address of I/O module
Remedy:
Check if the 24V line that is input for the General I/O unit of the corresponding station is correctly wired.
Description:
Sub code: shows the error code of Fronius power source.
Remedy:
Confirm the Fronius’s manual.
Description:
The pullback was executed when the shock detection function was invalid.
Remedy:
Check the following settings.
Shock Detection Function. Pullback signal
Description:
ASF04 board
Pullback axis mismatch
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN in maintenance mode, and then contact your Yaskawa representative about occurrence status (operating procedure).
Description:
ASF04 board
Pullback signal not detected
Remedy:
If ASF04 board is used, need to confirm the following.
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF04 board. Save the CMOS.BIN before replace the board to be safe.
Description:
Sub Code: Represents the axis connected to the SDCA01 board where ALARM SYNC(SERVO) has occurred.
Remedy:
Clear the alarm that occurred on the other SDCA01 board.
Description:
Sub Code: Gun No.
Remedy:
Check the setting of pressure.
Content:
An error was detected in the voltage value of the CPS power,
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, turn the power OFF then back ON.
(3) If the alarm occurs again, replace the following unit.
Description:
Sub Code
0001: OT(Robot)
Remedy:
Overrun limit switch is released. Select “OVERRUN&SHOCK SENSOR” under sub menu “ROBOT” to reset the limit switch. After that, perform avoidance movement by jog operation.
Description:
Sub Code
0001:OT1
0010:OT2
0100:OT3
1000:OT4
Remedy:
Overrun limit switch is released. Select “OVERRUN&SHOCK SENSOR” under sub menu “ROBOT” to reset the limit switch. After that, perform avoidance movement by jog operation.
Content:
The system parameters are modified.
An attempt was made to turn ON the servo power supply after having modified the system parameters.
Remedy:
(1) Reset the alarm.
(2) Turn the power OFF then back ON before turning ON the servo power supply.
Description:
Sub task being executed:
Although a job is being executed by instructed sub task, an attempt was made to execute another job by the sub task.
Remedy:
(1) Reset the alarm.
(2) Check if other JOB has been already executed in the same task which is used in the PSTART. If same task need to be executed in series, add PWAIT to confirm if the previous task end.
Description:
Group axis being used:
The job operated by another sub task uses the same group axis.
Remedy:
(1) Reset the alarm.
(2) Check if the control group of the JOB which is used in the PSTART has been already executed in other task. If the same group need to be executed in series, add PWAIT to confirm if the other task end.
Description:
Multiple start of same job:
The job that was tried to be started was executed by another sub task.
Remedy:
(1) Reset the alarm.
(2) Check if the JOB which is used in the PSTART has been already executed in other task. If the same job need to be executed in series, add PWAIT to confirm if the other task end.
Description:
Unregistered master job:
Although the master job was not registered, an attempt was made to execute PSTART SUB (job name omitted).
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Synchronization instruction error:
When restarted by PSTART, synchronization instruction status of the sub task under interruption was different from the status to restart.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Stopped by an alarm:
An attempt was made to start the sub task which is stopped by an alarm.
Remedy:
Check the following settings.
Description:
Synchronization task specification of SYNC instruction omit error
Remedy:
(1) Reset the alarm.
(2) Check the following setting.
Description:
The task is specified by synchronization task of SYNC instruction.
Remedy:
(1) Reset the alarm.
(2) Check the following setting.
Description:
I/O jog being executed
Remedy:
(1) Reset the alarm.
(2) Check the following setting.
Description:
Separate group axis being used
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
The servo power supply is OFF.
Remedy:
(1) Reset the alarm.
(2) Check the following setting.
Description:
Twin synchronous task ID error
Remedy:
(1) Reset the alarm.
(2) Check the following setting.
Description:
PSTART instruction is the old specification.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
PWAIT instruction is the old specification.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Sub task to be set PSTART has been already executed.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
An attempt was made to start up the control group where IO speed control is activated by a job.
Remedy:
(1) Reset the alarm.
(2) Check the status of IOSPDCTRL operation setting. The control group of which setting status is “VALID” cannot be started up by a job.
(3) Modify the job so as not to start up the control group in which IO speed control is activated.
Description:
MotoPlus is operating
Remedy:
(1) Reset the alarm.
(2) Check the following setting.
Description:
Sub Code1 to 245: Signifies the data transmission error.
Remedy:
(1) Reset the alarm.
(2) Refer to the instruction manual for Data Transmission Function for details.
Description:
Sub Code1 to 245: Signifies the data transmission error.
Remedy:
(1) Reset the alarm.
(2) Refer to the instruction manual for Data Transmission Function for details.
Description:
Sub Code1 to 245: Signifies the data transmission error.
Remedy:
(1) Reset the alarm.
(2) Refer to the instruction manual for Data Transmission Function for details.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
0000_0000_0000_0001: Detector circuit error.
0000_0000_0000_0010: Fuse blown (AIO board)
0000_0000_0000_0011: External 24V power supply error.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Check the insertion and connection of the followings.
Content:
This alarm occurs if the shock sensor signal is detected.
Remedy:
Shock sensor is activated. Select “OVERRUN&SHOCK SENSOR” under sub menu “ROBOT” to reset the sensor. After that, perform avoidance movement by jog operation.
Description:
Retry over of NAK
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the communication setting and communication wiring is correct.
Description:
Retry over for timeout in timer A
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the communication setting and communication wiring is correct.
Description:
Retry over for mutual response error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the communication setting and communication wiring is correct.
Description:
Reception timeout (timer A)
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the communication setting and communication wiring is correct.
Description:
Reception timeout (timer B)
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the communication setting and communication wiring is correct.
Description:
Heading length is too short.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, send EOT code to release the data link and then check that the sending side data is correctly set.
(3) Check that the communication setting is correct.
Description:
Heading length is too long.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, send EOT code to release the data link and then check that the sending side data is correctly set.
(3) Check that the communication setting is correct.
Description:
The header No. error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, send EOT code to release the data link and then check that the sending side data is correctly set.
(3) Check that the communication setting is correct.
Description:
The text length exceeded 256 characters.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, send EOT code to release the data link and then check that the sending side data is correctly set.
(3) Check that the communication setting is correct.
Description:
Illegal data received
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, send EOT code to release the data link and then check that the sending side data is correctly set.
(3) Check that the communication setting is correct.
Description:
Overrun error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the communication setting and communication wiring is correct.
Description:
Parity error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the communication setting and communication wiring is correct.
Description:
Framing error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the communication setting and communication wiring is correct.
Description:
Transmission timeout (timer A)
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the communication setting and communication wiring is correct.
Description:
Transmission timeout (timer B)
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the communication setting and communication wiring is correct.
Description:
Received EOT while waiting ACK.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the setting of communication or transmission side data is correctly set.
Description:
Received EOT while waiting ENQ.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the setting of communication or transmission side data is correctly set.
Description:
Received EOT before last block reception.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the setting of communication or transmission side data is correctly set.
Description:
Received codes other than EOT after last block reception.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the setting of communication or transmission side data is correctly set.
Description:
Transmission data contents error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the setting of communication or transmission side data is correctly set.
Description:
Trans error or protocol error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the setting of communication or transmission side data is correctly set.
Description:
The SDCA01 board # 1generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the brake connection if there is a ground fault or short circuit.
Description:
The SDCA01 board # 2 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the brake connection if there is a ground fault or short circuit.
Description:
The SDCA01 board # 3 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the brake connection if there is a ground fault or short circuit.
Description:
The SDCA01 board # 4 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the brake connection if there is a ground fault or short circuit.
Description:
The SDCA01 board # 5 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the brake connection if there is a ground fault or short circuit.
Description:
The SDCA01 board # 6generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the brake connection if there is a ground fault or short circuit.
Description:
The SDCA01 board # 7generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the brake connection if there is a ground fault or short circuit.
Description:
The SDCA01 board # 8generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the brake connection if there is a ground fault or short circuit.
Description:
The SDCA01 board # 1generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check fan power line if there is a ground fault or short circuit.
Description:
The SDCA01 board # 2 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check fan power line if there is a ground fault or short circuit.
Description:
The SDCA01 board # 3 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check fan power line if there is a ground fault or short circuit.
Description:
The SDCA01 board # 4 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check fan power line if there is a ground fault or short circuit.
Description:
The SDCA01 board # 5 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check fan power line if there is a ground fault or short circuit.
Description:
The SDCA01 board # 6 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check fan power line if there is a ground fault or short circuit.
Description:
The SDCA01 board # 7 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check fan power line if there is a ground fault or short circuit.
Description:
The SDCA01 board # 8 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check fan power line if there is a ground fault or short circuit.
Description:
Sub Code 1 to 8: Signifies the ASF01 board No. in which the alarm occurred
Remedy:
Replace the CPS01K* unit.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) Replace the cooling fan of manipulator.
Check the wiring from a manipulator to a servo board.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) Replace the cooling fan of manipulator.
Check the wiring from a manipulator to a servo board.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
Replace the cooling fan of manipulator.
Check the wiring from a manipulator to a servo board.
Description:
The specified file number is incorrect.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
The specified file set value is incorrect.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Calibration could not be executed.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
The communication port for the vision system could not be initialized.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Time-out occurred during data transmission.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Time-out occurred during data reception.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
The data received from the vision system is incorrect.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
The pixel coordinates value was not able to be converted into the robot coordinates.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Failed to read or write the position type variable (P variable).
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Use memory is lacking and the area could not be obtained.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting value of measurement item (FT) is incorrect.
Remedy:
(1) Reset the alarm.
(2) Correct the setting value of a measurement item.
Description:
The data for the vision execution command is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The number of waiting commands sent by Vision sensor exceeded the limit.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check the command sent by Vision sensor.
(3) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
File access error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the communication setting and communication wiring is correct.
Description:
File data error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the setting of communication or file data is correctly set.
Description:
Calibration execution error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the setting of communication or transmission side data is correctly set.
Description:
ACP01 port initialize error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the setting of communication or ACP01 port is correctly set.
Description:
Time-out occurred during data transmission.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the communication setting and communication wiring is correct.
Description:
Time-out occurred during data reception.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the communication setting and communication wiring is correct.
Description:
Receive data error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the communication setting and communication wiring is correct.
Description:
Coordinate conversion error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the setting of communication or transmission side data is correctly set.
Description:
Position type variable access error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the setting of communication or transmission side data is correctly set.
Description:
Failed to store the area.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Measurement item setting error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the setting of communication or transmission side data is correctly set.
Description:
Tag setting error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the setting of communication or transmission side data is correctly set.
Description:
Wait status table FULL
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the setting of communication or transmission side data is correctly set.
Description:
System error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PBOX cannot be edited.
Remedy:
(1) Reset the alarm.
(2) Check the following setting.
Description:
The source job cannot be edited.
Remedy:
(1) Reset the alarm.
(2) Check the following setting.
Description:
The converted job cannot be edited.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
The memory area for job area is insufficient.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete unused jobs.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file. In that case, delete the unused jobs.
(4) If the error occurs again though the previous measures were executed, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The source job is not exist.
Remedy:
Check the following settings.
Description:
The memory area for position data of the job is insufficient.
Remedy:
(1) Reset the alarm.
(2) when the error occurs again, if there is an unnecessary teaching position, delete it.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file. In that case, delete the unused jobs.
(4) If the error occurs again though the previous measures were executed, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The job under execution is specified as the conversion job.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Sub Code: XY
X : Servo board(SV#X)
Y : Power-ON unit (TU#Y)
Remedy:
(1) Reset the alarm.
(2) Replace the timing belt of the manipulator.
Check the connection between manipulator and servo board.
Description:
Monitor ON was executed in Monitor ON.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Analog CH specification or register specification is not exist.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
The number of samplings exceeds the set value.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Sub Code: Corresponding master-axes and slave-axes are displayed by the bit.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
An error occurred when the notification of the APP task re-initialization was processed in the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when the re-initialization response was received in the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The incomplete task of re-initialization was unsuccessfully completed in the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when the semaphore for re-initialization was received in the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when the re-initialization mail was sent in the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the exclusive process of the storage area control table of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Time-out occurred in the re-initialization response receiving process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the re-initialization response receiving process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Receiving data size error occurred in the re-initialization response receiving process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the Web server task mail receiving process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the FTP server task mail receiving process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the FTP client task mail receiving process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Illegal e-mail data were received in the Web server task of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Illegal e-mail data were received in the FTP server task of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Illegal e-mail data were received in the FTP client task of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the data size written to PCI of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when the request to write PCI data was received in the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The request of the undefined transmission was received in the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the transmission request of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The transmission request without data was received in the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The transmission request of illegal data length was received in the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Illegal mail data ware received in the DNS task of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Illegal mail data was transmitted in the DNS task of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in storing process of memory which is used in the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the buffer for request to write PCI getting process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The socket of the Ethernet function was full and was not able to create a socket.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the semaphore of socket control table of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the creation of receiving socket during the UDP process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the creation of transmission socket during the UDP process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Illegal data were received in the UDP process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Transmission error occurred in the UDP process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The SELECT operation was not successfully completed in the UDP process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The communication error was occurred in the UDP process of the WAIT ROBOT function.
Remedy:
(1) Reset the alarm.
(2) Check the network setting for the robot controller.
Description:
The re-initialization notification of illegal data length was received in the UDP process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The re-initialization notification of illegal data was received in the UDP process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The PCI write process was not successfully completed in the UDP process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The transmission request of illegal data length was received in the UDP process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The transmission request of illegal data was received in the UDP process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The socket table was not successfully created in the TCP process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the process of the TCP server initialization of the Ethernet function.
Remedy:
(1) Make sure that there is no communication device with the same IP address in the network.
(2) If DHCP is enabled, make sure that the correct IP address is leased from the DHCP server.
Description:
An error occurred in connection detecting process of TCP server of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the connection detection checking process of TCP server of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
Cooling fan setting parameter disabled.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Content:
TOYOPUC is in stopped state.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
The PCI bus state of the TOYOPUC turns to “ER”.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Alarm code specification error
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Task specification error
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Motion mode specification error
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Alarm num error
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
An error occurred at SVON instruction execution.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Content:
An error occurred at PRINT instruction execution.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
DIALOG instruction control error
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Messages and buttons are not registered.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Buttons are not registered.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
The error on setting of time difference value occurred in the SNTP process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The error on setting of time-out value occurred in the SNTP process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The error on setting of reference interval value occurred in the SNTP process of the Ethernet function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The IP address error occurred in the SNTP process of the Ethernet function.
Remedy:
Check the following settings.
Description:
Time-out occurred in the SNTP process
of the Ethernet function.
Remedy:
Check the following settings.
Description:
The server time is not synchronized in the SNTP process of the Ethernet function.
Remedy:
Check the following settings.
Description:
The SNTP process of the Ethernet function is not compliant with the version that the server sent.
Remedy:
Use the server compliant with the SNTP version 3.
Description:
Illegal parameters were found in the SNTP process of the Ethernet function.
Remedy:
Check the following settings.
Description:
The SNTP process of the Ethernet function was not successfully completed.
Remedy:
Check the following settings.
Description:
The name resolution error occurred in the SNTP process of the Ethernet function.
Remedy:
Check the following settings.
Description:
The error on getting of server address occurred in the SNTP process of the Ethernet function.
Remedy:
Check the following settings.
Description:
The server setting is incorrect in the SNTP process of the Ethernet function (for future use).
Remedy:
Check the following settings.
Description:
FN591 was executed 11 or more times in a row.
Remedy:
(1) Reset the alarm.
(2) Don’t set FN593 11 or more times in a row. Review the teaching.
Description:
There is invalid relay number in the SYSTEM LADDER.
Remedy:
Save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
There is invalid relay number in the USER LADDER.
Remedy:
Set the security to management mode and compile the ladder program. If any error occurs, modify the invalid relay number to complete the compiling.
Valid range
General Input:00010to05127
General Output:10010to15127
External Input:20010to25127
External Output:30010to35127
Specific Input:40010to41607
Specific Output:50010to53007
I/F Panel Input:60010to60647
Auxiliary Relay:70010to79997
Control Input:80010to85127
Pseudo Input:87010to87207
Network Input:27010to29567
Network output:37010to39567
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
Check the following settings.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
Check the following settings.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
Check the following settings.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
Check the following settings.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
Check the following settings.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
Check the following settings.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
Check the following settings.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
Check the following settings.
Content:
An error occurred during the editing operation of the user coordinates file.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the user coordinates file in maintenance mode, and then load the user coordinates file saved in the external memory device.
Description:
Trace level value is abnormal.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Trace data is abnormal.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Time stamp value is abnormal.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Trace level value is abnormal.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Abnormal variable is specified.
Remedy:
Check the following setting;
Description:
Exceeded the maximum trace number.
Remedy:
Execute TRACESAVE or TRACERST.
Description:
The overrun limit switch of the control group that corresponds to the indicated sub code was released.
Remedy:
Overrun limit switch is released. Select “OVERRUN&SHOCK SENSOR” under sub menu “ROBOT” to reset the limit switch.
Description:
The overrun limit switch of the control group that corresponds to the indicated sub code was released.
Remedy:
Overrun limit switch is released. Select “OVERRUN&SHOCK SENSOR” under sub menu “ROBOT” to reset the limit switch.
Description:
The SDCA01 board # 1 generates an alarm.
Remedy:
Move the manipulator in teach mode to the position where there is no torque on the driving belt.
(1) Check the timing belt tension.
(2) Check the wiring between manipulator and the machine safety unit (ASF01 board).
Description:
The SDCA01 board # 2 generates an alarm.
Remedy:
Move the manipulator in teach mode to the position where there is no torque on the driving belt.
(1) Check the timing belt tension.
(2) Check the wiring between manipulator and the machine safety unit (ASF01 board).
Description:
The SDCA01 board # 3 generates an alarm.
Remedy:
Move the manipulator in teach mode to the position where there is no torque on the driving belt.
(1) Check the timing belt tension.
(2) Check the wiring between manipulator and the machine safety unit (ASF01 board).
Description:
The SDCA01 board # 4 generates an alarm.
Remedy:
Move the manipulator in teach mode to the position where there is no torque on the driving belt.
(1) Check the timing belt tension.
(2) Check the wiring between manipulator and the machine safety unit (ASF01 board).
Description:
The SDCA01 board # 5 generates an alarm.
Remedy:
Move the manipulator in teach mode to the position where there is no torque on the driving belt.
(1) Check the timing belt tension.
(2) Check the wiring between manipulator and the machine safety unit (ASF01 board).
Description:
The SDCA01 board # 6 generates an alarm.
Remedy:
Move the manipulator in teach mode to the position where there is no torque on the driving belt.
(1) Check the timing belt tension.
(2) Check the wiring between manipulator and the machine safety unit (ASF01 board).
Description:
The SDCA01 board # 7 generates an alarm.
Remedy:
Move the manipulator in teach mode to the position where there is no torque on the driving belt.
(1) Check the timing belt tension.
(2) Check the wiring between manipulator and the machine safety unit (ASF01 board).
Description:
The SDCA01 board # 8 generates an alarm.
Remedy:
Move the manipulator in teach mode to the position where there is no torque on the driving belt.
(1) Check the timing belt tension.
(2) Check the wiring between manipulator and the machine safety unit (ASF01 board).
Description:
The SDCA01 board # 1 generates an alarm.
Remedy:
Refer to the instruction manuals for the cooling unit in use.
Description:
The SDCA01 board # 2 generates an alarm.
Remedy:
Refer to the instruction manuals for the cooling unit in use.
Description:
The SDCA01 board # 3 generates an alarm.
Remedy:
Refer to the instruction manuals for the cooling unit in use.
Description:
The SDCA01 board # 4 generates an alarm.
Remedy:
Refer to the instruction manuals for the cooling unit in use.
Description:
The SDCA01 board # 5 generates an alarm.
Remedy:
Refer to the instruction manuals for the cooling unit in use.
Description:
The SDCA01 board # 6 generates an alarm.
Remedy:
Refer to the instruction manuals for the cooling unit in use.
Description:
The SDCA01 board # 7 generates an alarm.
Remedy:
Refer to the instruction manuals for the cooling unit in use.
Description:
The SDCA01 board # 8 generates an alarm.
Remedy:
Refer to the instruction manuals for the cooling unit in use.
Description:
The SDCA01 board # 1 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 2 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 3 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 4 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 5 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 6 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 7 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 8 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 1 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 2 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 3 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 4 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 5 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 6 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 7 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
The SDCA01 board # 8 generates an alarm.
Remedy:
(1) Reset the alarm.
(2) Check the connection and insertion of the cable and connector for the cooling fan.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) Replace the cooling fan of manipulator.
Check the wiring from a manipulator to a servo board.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) Replace the cooling fan of manipulator.
Check the wiring from a manipulator to a servo board.
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Check the fuse(F1) in the YFL21 board is not disconnected.
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Replace the contactor(-K70).
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Check the status of circuit protector.
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Check the status of circuit protector.
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Check the status of circuit protector.
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Check the status of circuit protector.
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Check the status of circuit protector.
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Replace the ethernet switch(-X273).
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Check the status of circuit protector.
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Check the following setteing.
(1) DC24V output from I/O expansion unit is correct.
(2) F1 or F2 fuse in I/O expansion unit is not blown.
(3) A short circuit or ground fault has not occurred in IN/OUT line of I/O expansion unit.
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Check the status of circuit protector.
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Confirm whether YFL22 board is being used.
(1) when being unused, confirm following setting.
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
(1) Check the circuit protector. If there is a switch with the LED emitting red, press the reset button and confirm the light turns green.
(2) If the reset button is pressed and the switch LED does not turn green, check for short circuit or ground fault at a the 24V powera supply line of the circuit protector.
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Replace the fuse(F2) in the YFL21 board.
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Replace the power supply
Description:
Sub Code: Signifies the YFL21 board number in which the alarm occurred.
Remedy:
Replace the power supply
Description:
Sub Code: Signifies the YFL22 board number in which the alarm occurred.
Remedy:
Replace the fuse(F11) in the YFL22 board.
Description:
Sub Code: Signifies the YFL22 board number in which the alarm occurred.
Remedy:
Replace the fuse(F12) in the YFL22 board.
Description:
Sub Code: Signifies the YFL22 board number in which the alarm occurred.
Remedy:
Replace the fuse(F13) in the YFL22 board.
Description:
Sub Code: Signifies the YFL22 board number in which the alarm occurred.
Remedy:
Replace the fuse(F14) in the YFL22 board.
Description:
Sub Code: Signifies the YFL22 board number in which the alarm occurred.
Remedy:
Replace the fuse(F15) in the YFL22 board.
Description:
Sub Code: Signifies the YFL22 board number in which the alarm occurred.
Remedy:
Replace the fuse(F16) in the YFL22 board.
Description:
Sub Code: Signifies the YFL22 board number in which the alarm occurred.
Remedy:
Replace the fuse(F17) in the YFL22 board.
Description:
Sub Code: Signifies the YFL22 board number in which the alarm occurred.
Remedy:
Replace the fuse(F18) in the YFL22 board.
Description:
Sub Code: Signifies the YFL22 board number in which the alarm occurred.
Remedy:
Replace the fuse(F19) in the YFL22 board.
Description:
TRACE file generation error
Remedy:
(1) Reset the alarm.
(2) Check the connection status of the USB in the YRC1000 controller and its available memory.
Description:
TRACE file open error
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
TRACE file writing error
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
TRACE file close error
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
TRACE file number error
Remedy:
Delete the trace files generated today from the USB on the YRC1000 controller.
Description:
TRACE file index error
Remedy:
Review the name of the trace files generated today in the USB on the YRC1000 controller.
Description:
The specified database doesn’t exist.
Remedy:
Check the setting of the following item;
Description:
Cannot access the specified database.
Remedy:
Delete the database file in the USB installed to the YRC1000 controller.
Description:
There is not enough space for 3D trace buffer.
Remedy:
Adjust the parameter: 3D trace sampling cycle:S3C1325.
Description:
Subcode means the number of incorrect circuit.
Remedy:
(1) Check the safety logic circuit setting.
(2) Check the safety functions setting in maintenance mode
Description:
Sub code 01 to 50: Signifies the internal software error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, turn the controller power OFF and then ON to check the operation.
(3) If the alarm occurs again, initialize the appropriate data in maintenance mode, and then load the data saved in the external memory device.
Description:
An error occurred during the access a job in parameter specifications.
Remedy:
Reset the alarm, and then try again.
Description:
Access time exceeded the limit during the access to a job.
Remedy:
Reset the alarm, and then try again.
Description:
The access to a job could not be performed with the specified job name.
Remedy:
Reset the alarm, and then try again.
Description:
A job was newly created with the same name of the job already specified in the memory.
Remedy:
Reset the alarm, and then try again.
Description:
A job was newly created with the same name of the job already specified in the memory.
Remedy:
Reset the alarm, and then try again.
Description:
The allowable job registration area (memory) was exceeded.
Remedy:
Delete unused jobs.
Description:
A job that did not exist in the memory was specified.
Remedy:
Reset the alarm, and then try again.
Description:
An attempt was made to change the contents for the job prohibited from being edited.
Remedy:
Release the prohibition.
Description:
An error occurred during the access to a job in handle value.
Remedy:
Reset the alarm, and then try again.
Description:
An error occurred in job data control system.
Remedy:
Reset the alarm, and then try again.
Description:
An error occurred in sequence number of the accessed job.
Remedy:
Reset the alarm, and then try again.
Description:
An error occurred in step number of the accessed job.
Remedy:
Reset the alarm, and then try again.
Description:
A job specified at job search did not exist in the memory.
Remedy:
Reset the alarm, and then try again.
Description:
There was an instruction that did not exist in a job because of inconsistency of the system software.
Remedy:
Reset the alarm, and then try again.
Description:
Unused handles were lacking when an attempt was made to open a job.
Remedy:
Reset the alarm, and then try again.
Description:
The number of instructions added to a job exceeded 9999.
Remedy:
Delete unnecessary instructions and add new instructions again.
Description:
The number of steps added to a job exceeded 9999.
Remedy:
Delete unnecessary steps and add new steps again.
Description:
Job information was not able to be expanded.
Remedy:
Reset the alarm, and then try again.
Description:
Job information was not able to be acquired.
Remedy:
Reset the alarm, and then try again.
Description:
An error occurred in cluster control.
Remedy:
Reset the alarm, and then try again.
Description:
Failed to read the cluster information.
Remedy:
Reset the alarm, and then try again.
Description:
Heap area could not be obtained.
Remedy:
Reset the alarm, and then try again.
Description:
The target for change is the line where editing is prohibited or the comment-out line.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, deactivate the prohibit setting for the target line or delete the comment-out line.
Description:
The marker job was incorrectly changed.
Remedy:
Reset the alarm, and then try again.
Description:
The configuration data is damaged.
Remedy:
Reset the alarm, and then try again.
Description:
The FAT area is damaged.
Remedy:
Reset the alarm, and then try again.
Description:
A job data in the memory was destroyed.
Remedy:
Reset the alarm, and then try again.
Description:
An error occurred in parameter specifications for the access to a job .
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
Access time exceeded the limit during the access to a job.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
Unapproved characters are used for a job name.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
A job was newly created with the same name of the job already specified in the memory.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
A job was newly created with the same name of the job already specified in the memory.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
The allowable job registration area (memory) was exceeded.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete unused jobs.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file. In that case, delete the unused jobs.
Description:
A job that did not exist in the memory was specified.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
An attempt was made to change the contents for the job prohibited from being edited.
Remedy:
Check the following settings.
Description:
An attempt was made to change the contents for the job prohibited from being edited.
Remedy:
Check the following settings.
Description:
An error occurred in job data control system.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
An error occurred in sequence number of the accessed job.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
An error occurred in step number of the accessed job.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
A job specified at job search did not exist in the memory.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
There was an instruction that did not exist in a job because of inconsistency of the system software.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
Unused handles were lacking when an attempt was made to open a job.
Remedy:
Check the following settings.
Description:
The number of instructions added to a job exceeded 9999.
Remedy:
Check the following settings.
Description:
The number of steps added to a job exceeded 9999.
Remedy:
Check the following settings.
Description:
A job was newly created with the same name of the undefined job already specified in the memory.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
Failed to expand job information during the access to a job.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
The accessed job was not opened.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
An error occurred in the cluster control process of the accessed job.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
An error occurred when reading the cluster information of the accessed job.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
Failed to acquire the necessary memory area during the access to a job.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
An attempt was made to change the contents for the line prohibited from being edited or the commented-out line.
Remedy:
(1) Reset the alarm.
(2) Cancel the LINE EDIT LOCK/COMMENT OUT settings of target lines in JOB CONTENTS screen.
Description:
The marker job was incorrectly changed.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
The configuration information for job data control is damaged.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
The FAT information for job data is damaged.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
A job data was destroyed.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
A job data in the memory was destroyed.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
The memory area for position data is lacking at the initialization of the position data control process.
Remedy:
Reset the alarm, and then try again.
Description:
The number of axes for all the control groups is zero at the initialization of the position data control process.
Remedy:
Reset the alarm, and then try again.
Description:
The number of axes for position data is zero.
Remedy:
Reset the alarm, and then try again.
Description:
The number of stored position data exceeded the maximum stored data at the initialization of the position data control process.
Remedy:
Reset the alarm, and then try again.
Description:
The memory size of the position data exceeded the maximum memory size at the initialization of the position data control process.
Remedy:
Reset the alarm, and then try again.
Description:
Unused position data file is destroyed.
Remedy:
Reset the alarm, and then try again.
Description:
Unused position data file does not exist.
Remedy:
Reset the alarm, and then try again.
Description:
Position data file is destroyed.
Remedy:
Reset the alarm, and then try again.
Description:
Position data control information is destroyed.
Remedy:
Reset the alarm, and then try again.
Description:
An error occurred in specified position data number.
Remedy:
Reset the alarm, and then try again.
Description:
Position data is not registered.
Remedy:
Reset the alarm, and then try again.
Description:
An attempt was made to access the undefined position data.
Remedy:
Reset the alarm, and then try again.
Description:
An attempt was made to access the position data for the undefined control group.
Remedy:
Reset the alarm, and then try again.
Description:
Position data control is not initialized.
Remedy:
Reset the alarm, and then try again.
Description:
The number of axes for the control groups exceeded the limit.
Remedy:
Reset the alarm, and then try again.
Description:
An error occurred in exclusive control during the position data control process.
Remedy:
Reset the alarm, and then try again.
Description:
An error occurred in exceptional control during the position data control process.
Remedy:
Reset the alarm, and then try again.
Description:
Inconsistency of data.
Remedy:
Reset the alarm, and then try again.
Description:
The number of axes for all the control groups is zero at the initialization of the position data control process
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
The number of axes for all the control groups is zero at the initialization of the position data control process
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
The number of axes for position data is zero.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
The number of stored position data exceeded the maximum stored data at the initialization of the position data control process.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
The memory size of the position data exceeded the maximum memory size at the initialization of the position data control process.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
Unused position data file is destroyed.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
Unused position data file does not exist.
Remedy:
Check the following settings.
Description:
Position data file is destroyed.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
Position data control information is destroyed.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
An error occurred in specified position data number.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
Position data is not registered.
Remedy:
Check the following settings.
Description:
An attempt was made to access the undefined position data.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
An attempt was made to access the position data for the undefined control group.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
Position data control is not initialized.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
The number of axes for the control groups exceeded the limit.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
An error occurred in exclusive control during the position data control process.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
An error occurred in exceptional control during the position data control process.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
Undefined position exists.
Remedy:
(1) Reset the alarm.
(2) If the error occurs again, delete the job where the alarm occurred.
(3) If the error occurs again after the previous measures were executed, initialize the job file in the maintenance mode, and then load the saved job file.
Description:
Sub Code 1 to 4: Signifies the internal software error during data transmission.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An interrupt undefined in the main command from the system control section occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An interrupt undefined in the sub command from the system control section occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The interrupt command that was sent previously from the system control section is being processed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error was detected in the interrupt command data from the system control section.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An undefined command was detected in the sub segment task of MOTION section.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An undefined command was detected in the servo-related processing of MOTION section.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An undefined command was detected in the offline processing task of MOTION section.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An undefined command was detected in the utility task of MOTION section.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Task Token is not generated.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Mail-box Token is not generated.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Semaphore Token is not generated.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
RMS receiving data error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
RMS sending data error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
RMS receiving unit error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Task generation error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Mail-box generation error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Semaphore generation error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
TCB area overflow
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Stack area overflow
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Mail-box area overflow
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Semaphore area overflow
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Interrupt main command error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect control group designation
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Offline bank semaphore reception error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
m_gen_area semaphore reception error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Offline HA processing timeout
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
DM_BANK flag error (DM_BANK conversion processing)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
S -> M offline processing command type error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Function specification error in the data transmission to the sensor board
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Error in designation of application in the request of general-purpose data preset for each application.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Mail-box of sequence task is not ready.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group usage undefined
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Segment task polling command error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Physical axis number error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The control group impossible to release the brake
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub-segment request FULL
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub-segment process timeout
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Data latch request FULL
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Data latch process timeout
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
AXIS command request FULL
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
AXIS command process timeout
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Positioning monitor request FULL
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Positioning monitor process timeout
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed AXIS servo OFF command request during category1 emergency stop
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
AXIS servo OFF command execution system not set during category1 emergency stop
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Conversion primary expression for Power Source command <-> EW command not prepared
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Duplicated request error during master control-group tracking
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
GVM shared resource semaphore error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Job queue DEQUE error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Conversion primary expression for painting device command <-> EW command not prepared
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Execution system decision table not set
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Unknown mode data (Without TEACH/PLAY mode data)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Shift-value output timeout of the general-purpose sensor
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Interrupt main status set
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
System number error at the master side in twin synchronous system
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No data link added to the command
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Setting status error of the user coordinates file
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Previous path data reference error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Target position preparation error in arc-retry shift motion mode
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Inner track zone status error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Instruction queue and instruction system data area overflow
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Offline answer bank flag error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Path and trace queue ENQUE BANK error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Pending and block end request FULL
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Base axis file type error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Output buffer SYSCON for automatic test data in use
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Conversion completion status for AXIS section feedback latch data not established
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
File C1 through C3 for calibration between manipulators not set
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
File C1 through C3 for conveyor calibration not set
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
HA function error (conv_pos_data())
Remedy:
(1) Check the following settings.
Description:
HA function error (conv_shift_data())
Remedy:
(1) Check the following settings.
Description:
HA function error (conv_pulse_to_angle())
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
HA function error (pr_atinf_pos_make())
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
HA function error (get_gun_ctrl_ori_angle())
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
HA function error (make_conv_frm_data())
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
HA function error (calc_dist_pos())
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group axis configuration information parameter error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Error in the parameter for the table for physical axes
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Error in the parameter for the table for physical TU
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Excessive number of control group axes in use
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
JOG and PLAY maximum speed setting parameter error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Reduction ratio setting parameter error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
feedback PPR setting parameter error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Job argument stack overflow
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Job argument stack underflow
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Designation error of the fetched feedback pulse area at preparation of current value
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Timeout for waiting permission to modify the number of averaging times
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Object undefined for CLEAR instruction
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No space in RT_BANK setting area for correction-amount data
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for variable write-in history at prereading (at ENQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for variable write-in history at prereading (at DEQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for variable write-in history at prereading (undefined operation)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for variable write-in history at prereading (data length too long)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for score-board setting history (at ENQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for score-board setting history (at DEQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for score-board setting history (undefined operation)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for score-board setting history (data length too long)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for instruction execution (at ENQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for instruction execution (at DEQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for instruction execution (undefined operation)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for instruction execution (data length too long)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for WORK ID conveyor (at ENQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for WORK ID conveyor (at DEQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for WORK ID conveyor (undefined operation)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for WORK ID conveyor (data length too long)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for WORK IN/OUT checking conveyor (at ENQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for WORK IN/OUT checking conveyor (at DEQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for WORK IN/OUT checking conveyor (undefined operation)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for WORK IN/OUT checking conveyor (data length too long)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for waiting for semaphore for LOCK instruction (at ENQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for waiting for semaphore for LOCK instruction (at DEQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for waiting for semaphore for LOCK instruction (undefined operation)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Queue operation error for waiting for semaphore for LOCK instruction (data length too long)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Functional safety command request is full.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Functional safety command request is latency over.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Transfer data overflow in functional safety readback data.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PFL command request is full.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PFL command request is latency over.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Transfer data overflow in PFL readback data.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Transfer data overflow in offline data bank
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Impossible to execute system exclusive for system job
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Event queue number range exceeded
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No motor-gun control group for ESRCH instruction
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The number of WORK ID data and the MAX. WORK FIND COUNT unmatched (MOTION NOT EQUAL CV)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The number of WORK IN/OUT data and the MAX. WORK FIND COUNT unmatched (MOTION NOT EQUAL CV)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Excessive number of scheduling for execution of instructions
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Instruction execution scheduling impossible
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Illegal 1st-line move instruction at execution of +SMOV instruction
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Impossible to execute the slave circular interpolation and the master circular interpolation at the same time
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Impossible to execute the slave spline interpolation and the master spline interpolation at the same time
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Illegal index value for a +MOVx instruction
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No xth-line move instruction exists where the master control group belongs.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Marking error for WORK ID conveyor queue (empty queue)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Marking error for WORK IN/OUT conveyor queue (empty queue)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Data error 1 at restarting after an emergency stop (actual status and the data status unmatched)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Data error 2 at restarting after an emergency stop (actual status and the data status unmatched)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Data error 3 at restarting after an emergency stop (actual status and the data status unmatched)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Timeout for receiving segment data output request
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The number which designates the setting area of correction amount in RT_BANK exceeded the limit value.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Task error of the function calling source (cv_sync_intr ( ))
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No control group for motor gun for clearance move instruction
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Motor gun condition file number error (including gun pressure file)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
GETTOOLW manipulator designation error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Overflow of entry number for instruction execution
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Data latch processing (function number overflow)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Data latch processing (real-time status number overflow)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed to set a timer unit. (No allocation space for timer unit setting)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Segment data missing (seg_t_req was not received in time.)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
GETS instruction internal error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
SETFILE undefined file
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
GETFILE undefined file
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The parameter was destroyed when a GETPRM instruction was executed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Null pointer assignment detected
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Function or other processing parameter error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic answer is not set at prereading (ADV_HA_ANS.flag == OFF)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Heap area obtainment failure (A_BANK)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Heap area obtainment failure (C_BANK)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Heap area obtainment failure (Instruction queue)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Heap area obtainment failure (Path/trace queue)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Heap area obtainment failure (IF-Express descriptor)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Error in setting impedance control mode.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Error in releasing impedance control mode.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Specified MSS system instance is not generated.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
API error(HDAS_get_alias_name())
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
GA generation number is over the limit.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
GA gene number is over the limit.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
GA initial generation number setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
GA control group error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Learning control analysis error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
HA function error (get_svspot_ntch_data())
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Paint instruction internal error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Paint recover control error
(Paint Gun parameter error)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Paint recover control error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Job completion time over
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Servo simulator averaging time change error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Precondition judgment target instruction search failure
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sealing instruction internal error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Heap area obtainment failure (speed recode queue)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Synchronized queue operation error for WORK ID conveyor (at ENQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Synchronized queue operation error for WORK ID conveyor (at DEQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Synchronized queue operation error for WORK ID conveyor (undefined operation)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Synchronized queue operation error for WORK ID conveyor (data length too long)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Synchronized queue operation error for WORK IN/OUT checking conveyor (at ENQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Synchronized queue operation error for WORK IN/OUT checking conveyor (at DEQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Synchronized queue operation error for WORK IN/OUT checking conveyor (undefined operation)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Synchronized queue operation error for WORK IN/OUT checking conveyor (data length too long)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Synchronized queue operation error for WORK ID conveyor or WORK IN/OUT conveyor (at DEQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Synchronized queue empty error for WORK ID conveyor (at execution of CVQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Synchronized queue empty error for WORK IN/OUT conveyor (at execution of CVQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
P-PLC suspend err
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
P-PLC suspend err
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
P-PLC suspend seq err
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
P-PLC suspend seq no err
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
P-PLC suspend seq no err
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PSTRIG suspend err
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PSTRIG suspend err
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PSTRIG suspend seq err
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Timing Control queue operation (at DEQUE)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting of the motor gun targeted with MOTOR GUN AUTO TUNING function is incorrect.
Remedy:
(1) Check the following settings.
Description:
ACK response error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Polling command release error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Heap area obtainment failure (M_SV Transfer delay area)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Heap area obtainment failure (M_SU Transfer delay area)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Heap area obtainment failure (M_PFL Transfer delay area)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Heap area obtainment failure (ASCII IF)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
SL undefined interrupt command (main command)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
SL undefined interrupt command (sub command)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Previous SL interrupt command processing
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
SL interrupt command data error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic section error (segment data all zero timeout)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
System clock (RTC) setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
System task priority arrangement error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
VxWorks primitive error (msgQCreate)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
VxWorks primitive error (msgQSend)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
VxWorks primitive error (semBCreate)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
VxWorks primitive error (semTake)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
VxWorks primitive error (msgQSend) Message queue is full.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed system job environment configuration
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failure to load the needed file for SOFTWARE PLC FunctioniFile not foundj.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, contact your YASKAWA representative. It is necessary to setup the startup SD card again for the controller.
Description:
Failure to load the needed file for SOFTWARE PLC FunctioniFile cannot be openedj.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, contact your YASKAWA representative. It is necessary to setup the startup SD card again for the controller.
Description:
Failure to load the needed file for SOFTWARE PLC FunctioniFile data errorj.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, contact your YASKAWA representative. It is necessary to setup the startup SD card again for the controller.
Description:
Failure to load the needed file for SOFTWARE PLC Function
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, contact your YASKAWA representative. It is necessary to setup the startup SD card again for the controller.
Description:
Failure to start the system program of the SOFTWARE PLC Function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN and SPLCDRV.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failure to start the system program of the SOFTWARE PLC Function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN and SPLCDRV.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failure to start the system program of the SOFTWARE PLC Function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN and SPLCDRV.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failure to start the system program of the SOFTWARE PLC Function.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN and SPLCDRV.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failure to load the SOFTWARE PLC dataiData transfer errorj
Remedy:
(1) Turn the power OFF then back ON.
(2) Initialize RAM drive and load the backuped SOFTWARE PLC data(SPLCDRV.BIN). Then try again.
(2) If the alarm occurs again, save the CMOS.BIN and SPLCDRV.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failure to load the SOFTWARE PLC dataifolder creation errorj.
Remedy:
(1) Turn the power OFF then back ON.
(2) Initialize RAM drive and load the backuped SOFTWARE PLC data(SPLCDRV.BIN). Then try again.
(2) If the alarm occurs again, save the CMOS.BIN and SPLCDRV.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failure to load the SOFTWARE PLC dataiData transfer errorj.
Remedy:
(1) Turn the power OFF then back ON.
(2) Initialize RAM drive and load the backuped SOFTWARE PLC data(SPLCDRV.BIN). Then try again.
(2) If the alarm occurs again, save the CMOS.BIN and SPLCDRV.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failure to load the SOFTWARE PLC dataiData transfer errorj.
Remedy:
(1) Turn the power OFF then back ON.
(2) Initialize RAM drive and load the backuped SOFTWARE PLC data(SPLCDRV.BIN). Then try again.
(2) If the alarm occurs again, save the CMOS.BIN and SPLCDRV.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed system job environment configuration
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Prereading task is not completed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The averaging buffer in the arithmetic section is destroyed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No previous bank exists.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The answer bank flag is ON.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in preparation of current position.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Mails could not correctly be received in the current task.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Spline-curve path designation error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The previous bank’s prereading conversion could not correctly be completed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
A manipulator designation error occurred at JOG operation using the external reference point.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Designation error of cubic interference coordinates
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Path control position data error of prereading bank
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Station/base axis motion command error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
User coordinates number error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Processing error in re-preparation of segment control data
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Prereading task not completed at master in twin synchronous system
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Dynamic model arithmetic error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Speed limit control error (excessive moment of gravity)
Remedy:
(1) Check the following settings.
Description:
Square root of a negative number
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The system number is not set at master in twin synchronous system.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
FORMCUT internal control error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arm interference check error (radius data referencing mistake)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arm interference check error (miscalculation using direct kinematics)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arm interference check error (L-axis expansion flag setting error)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arm interference check error (check-point re-setting error)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Impossible to edit the averaging buffer (zero division)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No master-group is designated at preparation of master-tool user coordinates.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Gauging function error (command designation error)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
A coordinated motion was attempted using the Following function.
Remedy:
Change the setting so that only the manipulator moves.
*The coordinated motion cannot be performed by the Following function.
Description:
Zero or a negative value is set for the bending speed of the Following function.
Remedy:
Set a positive value for the bending speed.
Description:
Zero or a negative value is set for the bending stroke of the Following function.
Remedy:
Set a positive value for the bending stroke.
Description:
Pulse linked JOG function error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Special JOG operation error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Segment overless: Segment excessive error
Remedy:
The teaching position cannot hold down the speed by the segment overless function. Reduce the teaching speed of the job.
Description:
Segment overless: Path calculation repeat error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Play path control: initialization error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Play path control: continue process error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Play path control: Step continuous initialization error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Play path control: step continuous motion execution process error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Approximation model internal control error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Pair coordinate system position calculation function error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
OPT higher acceleration and deceleration control is not allowed when Function acceleration and deceleration control is enabled.
Remedy:
Check the following settings.
Description:
Arithmetic error occurred when calculating the acceleration and deceleration time (Function acceleration and deceleration control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when recalculating the acceleration and deceleration time (Function acceleration and deceleration control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating PL control (Function acceleration and deceleration control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating Function acceleration and deceleration dry run.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating current path of continuous motion stop operation
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating next path of continuous motion stop operation
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating acceleration time when continuous motion in the prereading processing
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating deceleration time when continuous motion in the prereading processing
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating acceleration and deceleration time when teaching.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating acceleration and deceleration time for plucking in prereading processing 1
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating acceleration and deceleration time for plucking in prereading processing 2
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating acceleration and deceleration time for plucking in prereading processing 3
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating acceleration and deceleration time for plucking in prereading processing 4
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating acceleration and deceleration for PL control plucking in prereading processing 1
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating acceleration and deceleration for PL control plucking in prereading processing 2
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating acceleration and deceleration for plucking
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating acceleration and deceleration for PL control in prereading processing 1
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating acceleration and deceleration for PL control in prereading processing 2
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating acceleration and deceleration for PL control in prereading processing 3
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating acceleration and deceleration for PL control in prereading processing 4
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating acceleration and deceleration for PL control in prereading processing 5
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Press full synchronous function:Press synchronous execution error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Press full synchronous function:The press position carried out cycle movement over.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Press full synchronous function:Press synchronous position error
Remedy:
Execute Position Adjustment Function to correct the position gap between press position and the manipulator.
Description:
Press full synchronous function:Position search error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Posture control error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
HA Servo Simulation error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Timing control function control group error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Feedback approximation model table queue control error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Feedback approximation model data reference error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Speed corresponding position correction section multi step detection error
Remedy:
Do not register more than two move instructions within the section “SFTON CSPD” and “SFTOF CSPD”.
Description:
Speed corresponding position correction control group error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Speed corresponding position correction start time ratio error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Speed corresponding position correction speed override level error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
For HA debug use
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Data setting error in offline data bank
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Data setting error in offline answer bank
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
OFF_USER_POS occupation control error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
OFF_USER_POS valid control error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Mail-receiving error of offline task
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Offline occupation control error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
OFF_USER_ROT_POS occupation control error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
OFF_USER_ROT_POS valid control error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
OFF_CV_CALIB_POS occupation control error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
OFF_CV_CALIB_POS valid control error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect teaching for offline conveyor tracking turntable function
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No manipulator is designated for offline conveyor tracking turntable function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detour posture control setup process error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
FORMCUT setup process error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PRESS SYNCHRONOUS setup process error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Local variable is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Memory area for local variable could not be obtained.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The local variable area could not be secured when calling the job.
Remedy:
The number of reserved local variable areas has exceeded the upper limit.
Review the job call location as follows and reduce the number of times the local variable area is secured.
-For job calls that do not need to return to the caller, change them to JUMP instructions instead of CALL instructions.
-When you no longer need to return to the caller, execute CLEAR STACK to reset the job call stack.
Description:
An error occurred in exclusive control.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Handle value is invalid for specified local variable.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Handle value is incorrect for specified local variable.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when memory area for local variable was released.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when memory area for local variable was registered.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Local variable control process is not initialized.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Local variable area shared heap area.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in exclusive control.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in exclusive control when control of the local variable was processed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Control group
Remedy:
Turn OFF the servo power supply, and then turn ON the servo power supply for the group axis to be operated.
Description:
Sub Code: Control group
Remedy:
- Turn OFF the servo power supply, and then turn ON the servo power supply for the group axis to be operated.
Description:
An error occurred in control process for memory play file.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The arrangement address information is destroyed for memory play file system.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The fixed control information is destroyed for memory play file system.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The fixed control information is destroyed for memory play file system.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An attempt was made to newly register the memory play file under use.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in checking written sampling data when the data was written to CMOS.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An attempt was made to access an unused memory play file data.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The memory play file is destroyed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The memory area for sampling data is full.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The sampling data is destroyed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Data in control process for memory play file is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The sampling data is scanned only at top or end position.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The memory play file system is not initialized.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The offset value is out of range at sampling data scanning.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Signifies the control axis number which detected an error
Remedy:
Check the following settings.
Description:
The communication channel could not be opened/closed at OPEN/CLOSE instruction execution.
Remedy:
Check the following settings.
Description:
The communication port is already opened.
Remedy:
Check the following settings.
The serial port setting
Description:
The communication port is not opened.
Remedy:
Check the following settings.
The serial port setting
Description:
No space was found in data sent buffer.
Remedy:
Check the following settings.
The serial port setting
Description:
The setting value for the event queue designation parameter is incorrect.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
The type of output data is incorrect.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
The serial port setting
Content:
The YRC1000 divides the job; instruction data and position data, into separate files to save.
This alarm occurs if it detects the inconsistency between the Job instruction and position file.
The followings are the causes of the inconsistency.
Cause 1: Single position data is chained by the plural Job instruction data. (Overlapped chain)
Cause 2: Job instruction file chains the unregistered position data. (Unregistered position data chain)
Cause 3: Registered position data is not chained.(Unchained position data)
Remedy:
(1) Reset the alarm, and then execute following operation.
Description:
An error occurred in the acquisition process of the IP address during the IP address monitoring process of the Ethernet function.(LAN interface 2)
Remedy:
Check the following settings.
Description:
An error occurred in the acquisition process of subnet mask during the network service data creation process of the Ethernet function.(LAN interface 2)
Remedy:
Check the following settings.
Description:
An error occurred in the acquisition process of gateway during the network service data creation process of the Ethernet function.
Remedy:
Check the following settings.
Description:
An error occurred in the conversion process of gateway address during the network service data creation process of the Ethernet function.
Remedy:
Check the following settings.
Description:
An error occurred in the conversion process of DNS server address during the network service data creation process of the Ethernet function.
Remedy:
Check the following settings.
Description:
An error occurred in the acquisition process of domain during the network service data creation process of the Ethernet function.
Remedy:
Check the following settings.
Description:
An error occurred in the acquisition process of SNTP server during the network service data creation process of the Ethernet function.
Remedy:
Check the following settings.
Description:
An error occurred in the acquisition process of host name during the network service data creation process of the Ethernet function.
Remedy:
Check the following settings.
Description:
An error occurred in the newest DNS information getting process from DHCP server in the DNS process of the Ethernet function.
Remedy:
Check the following settings.
Description:
An error occurred in the setting process to update DNS information in the DNS process of the Ethernet function.
Remedy:
Check the following settings.
Description:
An error occurred in the setting clearing process to update DNS information in the DNS process of the Ethernet function.
Remedy:
Check the following settings.
Description:
The subnet mask was not able to be acquired in the DHCP information update process of the Ethernet function.(LAN interface 2)
Remedy:
Check the following settings.
Description:
Subnet mask update error occurred in the DHCP information update process of the Ethernet function.
Remedy:
Check the following settings.
Description:
Gateway update error occurred in the DHCP information update process of the Ethernet function.
Remedy:
Check the following settings.
Description:
Gateway clear error occurred in the DHCP information update process of the Ethernet function.
Remedy:
Check the following settings.
Description:
IP address duplication was detected.(LAN interface 2)
Remedy:
Check the following settings.
Description:
IP address duplication was detected.
Remedy:
Check the following settings.
Description:
IP address can not be gotten or can not be updated via DHCP.(LAN interface 2)
Remedy:
Check the following settings and status.
Description:
Gateway setting is faulted.
Remedy:
Check the following settings.
Description:
Static route setting is faulted.(LAN interface 2, route 1)
Remedy:
Check the following settings.
Description:
NAT setting is faulted.(LAN interface 2)
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ACP01 board. Save the CMOS.BIN before replace the board to be safe. Replace the ACP01 board, and then remove the SD CARD from the failure ACP01 board to insert it into the new ACP01 board.
Description:
The host address to be used in ethernet function is not configured correctly.
Remedy:
Check the following settings.
Description:
Static route setting is faulted.(LAN interface 2, route 2)
Remedy:
Check the following settings.
Description:
An error occurred in the acquisition process of the IP address during the IP address monitoring process of the Ethernet function.(LAN interface 3)
Remedy:
Check the following settings.
Description:
An error occurred in the acquisition process of subnet mask during the network service data creation process of the Ethernet function.(LAN interface 3)
Remedy:
Check the following settings.
Description:
The subnet mask was not able to be acquired in the DHCP information update process of the Ethernet function.(LAN interface 3)
Remedy:
Check the following settings.
Description:
IP address duplication was detected.(LAN interface 3)
Remedy:
Check the following settings.
Description:
IP address can not be gotten or can not be updated via DHCP.(LAN interface 3)
Remedy:
Check the following settings and status.
Description:
Static route setting is faulted.(LAN interface 3, route 1)
Remedy:
Check the following settings.
Description:
NAT setting is faulted.(LAN interface 3)
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ACP01 board. Save the CMOS.BIN before replace the board to be safe. Replace the ACP01 board, and then remove the SD CARD from the failure ACP01 board to insert it into the new ACP01 board.
Description:
Static route setting is faulted.(LAN interface 3, route 2)
Remedy:
Check the following settings.
Description:
An error occurred in the acquisition process of the IP address during the IP address monitoring process of the Ethernet function.(LAN interface 4)
Remedy:
Check the following settings.
Description:
An error occurred in the acquisition process of subnet mask during the network service data creation process of the Ethernet function.(LAN interface 4)
Remedy:
Check the following settings.
Description:
The subnet mask was not able to be acquired in the DHCP information update process of the Ethernet function.(LAN interface 4)
Remedy:
Check the following settings.
Description:
IP address duplication was detected.(LAN interface 4)
Remedy:
Check the following settings.
Description:
IP address can not be gotten or can not be updated via DHCP.(LAN interface 4)
Remedy:
Check the following settings and status.
Description:
Static route setting is faulted.(LAN interface 4, route 1)
Remedy:
Check the following settings.
Description:
NAT setting is faulted.(LAN interface 4)
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ACP01 board. Save the CMOS.BIN before replace the board to be safe. Replace the ACP01 board, and then remove the SD CARD from the failure ACP01 board to insert it into the new ACP01 board.
Description:
Static route setting is faulted.(LAN interface 4, route 2)
Remedy:
Check the following settings.
Description:
An error occurred in the acquisition process of the IP address during the IP address monitoring process of the Ethernet function.(LAN interface 5)
Remedy:
Check the following settings.
Description:
An error occurred in the acquisition process of subnet mask during the network service data creation process of the Ethernet function.(LAN interface 5)
Remedy:
Check the following settings.
Description:
The subnet mask was not able to be acquired in the DHCP information update process of the Ethernet function.(LAN interface 5)
Remedy:
Check the following settings.
Description:
IP address duplication was detected.(LAN interface 5)
Remedy:
Check the following settings.
Description:
IP address can not be gotten or can not be updated via DHCP.(LAN interface 5)
Remedy:
Check the following settings and status.
Description:
Static route setting is faulted.(LAN interface 5, route 1)
Remedy:
Check the following settings.
Description:
NAT setting is faulted.(LAN interface 5)
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ACP01 board. Save the CMOS.BIN before replace the board to be safe. Replace the ACP01 board, and then remove the SD CARD from the failure ACP01 board to insert it into the new ACP01 board.
Description:
Static route setting is faulted.(LAN interface 5, route 2)
Remedy:
Check the following settings.
Description:
The IO module board connected with 0th serial bus exists.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error was detected in communications timeout with the I/O module board connected with 1st serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 2nd serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 3rd serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 4th serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 5th serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 6th serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 7th serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 8th serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 9th serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 10th serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 11th serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 12th serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 13th serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 14th serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 15th serial bus when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 1st PCI connector when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications with the I/O module board connected with 2nd PCI when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 3rd PCI when the control power turned ON.
Remedy:
Check the following settings.
Description:
An error was detected in communications timeout with the I/O module board connected with 4th PCI when the control power turned ON.
Remedy:
Check the following settings.
Description:
I/F board unconnected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, check the connection with the I/F board.
Description:
JL012 access time out.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, check the connection and inserting state of the following cable.
Description:
JL012 data setting error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, check the connection and inserting state of the following cable.
Description:
DeviceNet response error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, check the connection and inserting state of the following cable.
Description:
Data sheet format error.
Remedy:
The connected spot welder isn’t corresponded to. Save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
JL012 data overflow.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, check the connection and inserting state of the following cable.
Description:
Initialization error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Not found the spot welder number.
Remedy:
Check the following settings.
Description:
ASW file size over.
Remedy:
The connected spot welder isn’t corresponded to. Save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
System call error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Welding power source number.
Remedy:
Confirm the following content.
Step1: Check what kind of the error code is expressed on the front panel of Fronius power source.
Step2: Check according with the Fronius’s manual.
Description:
Error from welder 1.
Remedy:
When finish system reset, Shut down the welding power source.
Description:
Error from welder 2.
Remedy:
When finish system reset, Shut down the welding power source.
Description:
Error from welder 3.
Remedy:
When finish system reset, Shut down the welding power source.
Description:
Error from welder 4.
Remedy:
When finish system reset, Shut down the welding power source.
Description:
Error from welder 5.
Remedy:
When finish system reset, Shut down the welding power source.
Description:
Error from welder 6.
Remedy:
When finish system reset, Shut down the welding power source.
Description:
Error from welder 7.
Remedy:
When finish system reset, Shut down the welding power source.
Description:
Error from welder 8.
Remedy:
When finish system reset, Shut down the welding power source.
Description:
Sub code : Error No. from welder.
Remedy:
When finish system reset, Shut down the welding power source.
Description:
Error from welder 1.
Remedy:
(1) Check if the output cable is short-circuited or grounded.
(2) The power circuit may be broken. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
(1) Check if the output cable is short-circuited or grounded.
(2) The power circuit may be broken. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
(1) Check if the output cable is short-circuited or grounded.
(2) The power circuit may be broken. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
(1) Check if the output cable is short-circuited or grounded.
(2) The power circuit may be broken. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
(1) Check if the output cable is short-circuited or grounded.
(2) The power circuit may be broken. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
(1) Check if the output cable is short-circuited or grounded.
(2) The power circuit may be broken. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
(1) Check if the output cable is short-circuited or grounded.
(2) The power circuit may be broken. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
(1) Check if the output cable is short-circuited or grounded.
(2) The power circuit may be broken. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
(1) Check if the output cable is short-circuited or grounded.
(2) The power circuit may be broken. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
Confirm the following content.
(1) Check that the torch cable or power cable is not grounded?
(2) Check that the contact tip does not contact the welding work piece?
(3) Check that the encoder cable is not damaged?
(4) Check if the screws of the connector terminal block are securely fastened. If the encoder cable is disconnected or the screws are loosened, the wire feeding speed becomes excessively fast and an error occurs in the wire feeding amount. Replace the encoder cable or fasten the screws of the connector terminal block.
Description:
Error from welder 2.
Remedy:
Confirm the following content.
(1) Check that the torch cable or power cable is not grounded?
(2) Check that the contact tip does not contact the welding work piece?
(3) Check that the encoder cable is not damaged?
(4) Check if the screws of the connector terminal block are securely fastened. If the encoder cable is disconnected or the screws are loosened, the wire feeding speed becomes excessively fast and an error occurs in the wire feeding amount. Replace the encoder cable or fasten the screws of the connector terminal block.
Description:
Error from welder 3.
Remedy:
Confirm the following content.
(1) Check that the torch cable or power cable is not grounded?
(2) Check that the contact tip does not contact the welding work piece?
(3) Check that the encoder cable is not damaged?
(4) Check if the screws of the connector terminal block are securely fastened. If the encoder cable is disconnected or the screws are loosened, the wire feeding speed becomes excessively fast and an error occurs in the wire feeding amount. Replace the encoder cable or fasten the screws of the connector terminal block.
Description:
Error from welder 4.
Remedy:
Confirm the following content.
(1) Check that the torch cable or power cable is not grounded?
(2) Check that the contact tip does not contact the welding work piece?
(3) Check that the encoder cable is not damaged?
(4) Check if the screws of the connector terminal block are securely fastened. If the encoder cable is disconnected or the screws are loosened, the wire feeding speed becomes excessively fast and an error occurs in the wire feeding amount. Replace the encoder cable or fasten the screws of the connector terminal block.
Description:
Error from welder 5.
Remedy:
Confirm the following content.
(1) Check that the torch cable or power cable is not grounded?
(2) Check that the contact tip does not contact the welding work piece?
(3) Check that the encoder cable is not damaged?
(4) Check if the screws of the connector terminal block are securely fastened. If the encoder cable is disconnected or the screws are loosened, the wire feeding speed becomes excessively fast and an error occurs in the wire feeding amount. Replace the encoder cable or fasten the screws of the connector terminal block.
Description:
Error from welder 6.
Remedy:
Confirm the following content.
(1) Check that the torch cable or power cable is not grounded?
(2) Check that the contact tip does not contact the welding work piece?
(3) Check that the encoder cable is not damaged?
(4) Check if the screws of the connector terminal block are securely fastened. If the encoder cable is disconnected or the screws are loosened, the wire feeding speed becomes excessively fast and an error occurs in the wire feeding amount. Replace the encoder cable or fasten the screws of the connector terminal block.
Description:
Error from welder 7.
Remedy:
Confirm the following content.
(1) Check that the torch cable or power cable is not grounded?
(2) Check that the contact tip does not contact the welding work piece?
(3) Check that the encoder cable is not damaged?
(4) Check if the screws of the connector terminal block are securely fastened. If the encoder cable is disconnected or the screws are loosened, the wire feeding speed becomes excessively fast and an error occurs in the wire feeding amount. Replace the encoder cable or fasten the screws of the connector terminal block.
Description:
Error from welder 8.
Remedy:
Confirm the following content.
(1) Check that the torch cable or power cable is not grounded?
(2) Check that the contact tip does not contact the welding work piece?
(3) Check that the encoder cable is not damaged?
(4) Check if the screws of the connector terminal block are securely fastened. If the encoder cable is disconnected or the screws are loosened, the wire feeding speed becomes excessively fast and an error occurs in the wire feeding amount. Replace the encoder cable or fasten the screws of the connector terminal block.
Description:
Sub code : Error No. from welder.
Remedy:
Confirm the following content.
(1) Check that the torch cable or power cable is not grounded?
(2) Check that the contact tip does not contact the welding work piece?
(3) Check that the encoder cable is not damaged?
(4) Check if the screws of the connector terminal block are securely fastened. If the encoder cable is disconnected or the screws are loosened, the wire feeding speed becomes excessively fast and an error occurs in the wire feeding amount. Replace the encoder cable or fasten the screws of the connector terminal block.
Description:
Error from welder 1.
Remedy:
Confirm the input voltage.
Description:
Error from welder 2.
Remedy:
Confirm the input voltage.
Description:
Error from welder 3.
Remedy:
Confirm the input voltage.
Description:
Error from welder 4.
Remedy:
Confirm the input voltage.
Description:
Error from welder 5.
Remedy:
Confirm the input voltage.
Description:
Error from welder 6.
Remedy:
Confirm the input voltage.
Description:
Error from welder 7.
Remedy:
Confirm the input voltage.
Description:
Error from welder 8.
Remedy:
Confirm the input voltage.
Description:
Error from welder 1.
Remedy:
(1) Check the ambient temperature (40 degrees centigrade or less) and operational ratio (60%).
(2) Check if there are dust, dirt, and clogging on the dust protective filter. Clean or replace the dust protective filter if necessary.
(3) In case of RL350, Check the thermal guard (Item No.410).
Description:
Error from welder 2.
Remedy:
(1) Check the ambient temperature (40 degrees centigrade or less) and operational ratio (60%).
(2) Check if there are dust, dirt, and clogging on the dust protective filter. Clean or replace the dust protective filter if necessary.
(3) In case of RL350, Check the thermal guard (Item No.410).
Description:
Error from welder 3.
Remedy:
(1) Check the ambient temperature (40 degrees centigrade or less) and operational ratio (60%).
(2) Check if there are dust, dirt, and clogging on the dust protective filter. Clean or replace the dust protective filter if necessary.
(3) In case of RL350, Check the thermal guard (Item No.410).
Description:
Error from welder 4.
Remedy:
(1) Check the ambient temperature (40 degrees centigrade or less) and operational ratio (60%).
(2) Check if there are dust, dirt, and clogging on the dust protective filter. Clean or replace the dust protective filter if necessary.
(3) In case of RL350, Check the thermal guard (Item No.410).
Description:
Error from welder 5.
Remedy:
(1) Check the ambient temperature (40 degrees centigrade or less) and operational ratio (60%).
(2) Check if there are dust, dirt, and clogging on the dust protective filter. Clean or replace the dust protective filter if necessary.
(3) In case of RL350, Check the thermal guard (Item No.410).
Description:
Error from welder 6.
Remedy:
(1) Check the ambient temperature (40 degrees centigrade or less) and operational ratio (60%).
(2) Check if there are dust, dirt, and clogging on the dust protective filter. Clean or replace the dust protective filter if necessary.
(3) In case of RL350, Check the thermal guard (Item No.410).
Description:
Error from welder 7.
Remedy:
(1) Check the ambient temperature (40 degrees centigrade or less) and operational ratio (60%).
(2) Check if there are dust, dirt, and clogging on the dust protective filter. Clean or replace the dust protective filter if necessary.
(3) In case of RL350, Check the thermal guard (Item No.410).
Description:
Error from welder 8.
Remedy:
(1) Check the ambient temperature (40 degrees centigrade or less) and operational ratio (60%).
(2) Check if there are dust, dirt, and clogging on the dust protective filter. Clean or replace the dust protective filter if necessary.
(3) In case of RL350, Check the thermal guard (Item No.410).
Description:
The temperature in the primary control circuit exceeds the specified value of the welding source.
Remedy:
(1) Check the ambient temperature (40 degrees centigrade or less) and operational ratio (60%).
(2) Check if there are dust, dirt, and clogging on the dust protective filter. Clean or replace the dust protective filter if necessary.
(3) In case of RL350, Check the thermal guard of primary side (Item No.410).
In case of X350, Check the thermal guard of primary side(Item No.410).
Description:
The temperature in the secondary control circuit exceeds the specified value of the welding source.
Remedy:
(1) Check the ambient temperature (40 degrees centigrade or less) and operational ratio (60%).
(2) Check if there are dust, dirt, and clogging on the dust protective filter. Clean or replace the dust protective filter if necessary.
(3) In case of RL350, Check the thermal guard of secondary side (Item No.318).
In case of X350, Check the thermal guard of secondary side (Item No.410).
Description:
The temperature in the DC reactor exceeds the specified value of the welding source.
Remedy:
(1) Check the ambient temperature (40 degrees centigrade or less) and operational ratio (60%).
(2) Check if there are dust, dirt, and clogging on the dust protective filter. Clean or replace the dust protective filter if necessary.
(3) In case of RL350, Check the thermal guard of DCL2 (Item No.312).
In case of X350, Check the thermal guard of DCL2 (Item No.514).
Description:
The temperature in the Main board Pr(MB) exceeds the specified value of the welding source.
Remedy:
(1) Check the ambient temperature (40 degrees centigrade or less) and operational ratio (60%).
(2) Check if there are dust, dirt, and clogging on the dust protective filter. Clean or replace the dust protective filter if necessary.
(3) Replace the Main board Pr(MB)-030(Item No. 504).
Description:
Error from welder 1.
Remedy:
Confirm the input voltage.
Description:
Error from welder 2.
Remedy:
Confirm the input voltage.
Description:
Error from welder 3.
Remedy:
Confirm the input voltage.
Description:
Error from welder 4.
Remedy:
Confirm the input voltage.
Description:
Error from welder 5.
Remedy:
Confirm the input voltage.
Description:
Error from welder 6.
Remedy:
Confirm the input voltage.
Description:
Error from welder 7.
Remedy:
Confirm the input voltage.
Description:
Error from welder 8.
Remedy:
Confirm the input voltage.
Description:
Error from welder 1.
Remedy:
(1) Fill up the cooling water.
(2) Check the circuit of cooling water.
Description:
Error from welder 2.
Remedy:
(1) Fill up the cooling water.
(2) Check the circuit of cooling water.
Description:
Error from welder 3.
Remedy:
(1) Fill up the cooling water.
(2) Check the circuit of cooling water.
Description:
Error from welder 4.
Remedy:
(1) Fill up the cooling water.
(2) Check the circuit of cooling water.
Description:
Error from welder 5.
Remedy:
(1) Fill up the cooling water.
(2) Check the circuit of cooling water.
Description:
Error from welder 6.
Remedy:
(1) Fill up the cooling water.
(2) Check the circuit of cooling water.
Description:
Error from welder 7.
Remedy:
(1) Fill up the cooling water.
(2) Check the circuit of cooling water.
Description:
Error from welder 8.
Remedy:
(1) Fill up the cooling water.
(2) Check the circuit of cooling water.
Description:
Sub code : Error No. from welder.
Remedy:
(1) Fill up the cooling water.
(2) Check the circuit of cooling water.
Description:
Error from welder 1.
Remedy:
Confirm the following content.
(1) The LAN cable has not damaged.
(2) The Ethernet protocol address setting is correct. (Check that C parameter of the welding power source and RS parameter of the robot controller.)
(3) Welding power source is turn on.
(4) Please confirm the Ethernet setting (Ethernet function is effective
and sets an IP address (RS parameter , AxP parameter)) of the robot control unit.
Description:
Error from welder 2.
Remedy:
Confirm the following content.
(1) The LAN cable has not damaged.
(2) The Ethernet protocol address setting is correct. (Check that C parameter of the welding power source and RS parameter of the robot controller.)
(3) Welding power source is turn on.
(4) Please confirm the Ethernet setting (Ethernet function is effective
and sets an IP address (RS parameter , AxP parameter)) of the robot control unit.
Description:
Error from welder 3.
Remedy:
Confirm the following content.
(1) The LAN cable has not damaged.
(2) The Ethernet protocol address setting is correct. (Check that C parameter of the welding power source and RS parameter of the robot controller.)
(3) Welding power source is turn on.
(4) Please confirm the Ethernet setting (Ethernet function is effective
and sets an IP address (RS parameter , AxP parameter)) of the robot control unit.
Description:
Error from welder 4.
Remedy:
Confirm the following content.
(1) The LAN cable has not damaged.
(2) The Ethernet protocol address setting is correct. (Check that C parameter of the welding power source and RS parameter of the robot controller.)
(3) Welding power source is turn on.
(4) Please confirm the Ethernet setting (Ethernet function is effective
and sets an IP address (RS parameter , AxP parameter)) of the robot control unit.
Description:
Error from welder 5.
Remedy:
Confirm the following content.
(1) The LAN cable has not damaged.
(2) The Ethernet protocol address setting is correct. (Check that C parameter of the welding power source and RS parameter of the robot controller.)
(3) Welding power source is turn on.
(4) Please confirm the Ethernet setting (Ethernet function is effective
and sets an IP address (RS parameter , AxP parameter)) of the robot control unit.
Description:
Error from welder 6.
Remedy:
Confirm the following content.
(1) The LAN cable has not damaged.
(2) The Ethernet protocol address setting is correct. (Check that C parameter of the welding power source and RS parameter of the robot controller.)
(3) Welding power source is turn on.
(4) Please confirm the Ethernet setting (Ethernet function is effective
and sets an IP address (RS parameter , AxP parameter)) of the robot control unit.
Description:
Error from welder 7.
Remedy:
Confirm the following content.
(1) The LAN cable has not damaged.
(2) The Ethernet protocol address setting is correct. (Check that C parameter of the welding power source and RS parameter of the robot controller.)
(3) Welding power source is turn on.
(4) Please confirm the Ethernet setting (Ethernet function is effective
and sets an IP address (RS parameter , AxP parameter)) of the robot control unit.
Description:
Error from welder 8.
Remedy:
Confirm the following content.
(1) The LAN cable has not damaged.
(2) The Ethernet protocol address setting is correct. (Check that C parameter of the welding power source and RS parameter of the robot controller.)
(3) Welding power source is turn on.
(4) Please confirm the Ethernet setting (Ethernet function is effective
and sets an IP address (RS parameter , AxP parameter)) of the robot control unit.
Description:
Sub code : Error No. from welder.
Remedy:
Confirm the following content.
(1) The LAN cable has not damaged.
(2) The Ethernet protocol address setting is correct. (Check that C parameter of the welding power source and RS parameter of the robot controller.)
(3) Welding power source is turn on.
(4) Please confirm the Ethernet setting (Ethernet function is effective
and sets an IP address (RS parameter , AxP parameter)) of the robot control unit.
Description:
Error from welder 1.
Remedy:
Check the Node of the each welder power sources and robot controller.
Description:
Error from welder 2.
Remedy:
Check the Node of the each welder power sources and robot controller.
Description:
Error from welder 3.
Remedy:
Check the Node of the each welder power sources and robot controller.
Description:
Error from welder 4.
Remedy:
Check the Node of the each welder power sources and robot controller.
Description:
Error from welder 5.
Remedy:
Check the Node of the each welder power sources and robot controller.
Description:
Error from welder 6.
Remedy:
Check the Node of the each welder power sources and robot controller.
Description:
Error from welder 7.
Remedy:
Check the Node of the each welder power sources and robot controller.
Description:
Error from welder 8.
Remedy:
Check the Node of the each welder power sources and robot controller.
Description:
Sub code : Error No. from welder.
Remedy:
Check the Node of the each welder power sources and robot controller.
Description:
Error from welder 1.
Remedy:
Confirm the following content.
(1) LAN cable is not damaged.
(2) Protocol type of the VEW01 is correct. (is MOTOWELD type?)
Description:
Error from welder 2.
Remedy:
Confirm the following content.
(1) LAN cable is not damaged.
(2) Protocol type of the VEW01 is correct. (is MOTOWELD type?)
Description:
Error from welder 3.
Remedy:
Confirm the following content.
(1) LAN cable is not damaged.
(2) Protocol type of the VEW01 is correct. (is MOTOWELD type?)
Description:
Error from welder 4.
Remedy:
Confirm the following content.
(1) LAN cable is not damaged.
(2) Protocol type of the VEW01 is correct. (is MOTOWELD type?)
Description:
Error from welder 5.
Remedy:
Confirm the following content.
(1) LAN cable is not damaged.
(2) Protocol type of the VEW01 is correct. (is MOTOWELD type?)
Description:
Error from welder 6.
Remedy:
Confirm the following content.
(1) LAN cable is not damaged.
(2) Protocol type of the VEW01 is correct. (is MOTOWELD type?)
Description:
Error from welder 7.
Remedy:
Confirm the following content.
(1) LAN cable is not damaged.
(2) Protocol type of the VEW01 is correct. (is MOTOWELD type?)
Description:
Error from welder 8.
Remedy:
Confirm the following content.
(1) LAN cable is not damaged.
(2) Protocol type of the VEW01 is correct. (is MOTOWELD type?)
Description:
Sub code : Error No. from welder.
Remedy:
Confirm the following content.
(1) LAN cable is not damaged.
(2) Protocol type of the VEW01 is correct. (is MOTOWELD type?)
Description:
Error from welder 1.
Remedy:
Set the user file number 1.16.
Description:
Error from welder 2.
Remedy:
Set the user file number 1.16.
Description:
Error from welder 3.
Remedy:
Set the user file number 1.16.
Description:
Error from welder 4.
Remedy:
Set the user file number 1.16.
Description:
Error from welder 5.
Remedy:
Set the user file number 1.16.
Description:
Error from welder 6.
Remedy:
Set the user file number 1.16.
Description:
Error from welder 7.
Remedy:
Set the user file number 1.16.
Description:
Error from welder 8.
Remedy:
Set the user file number 1.16.
Description:
Sub code : Error No. from welder.
Remedy:
Set the user file number 1.16.
Description:
Error from welder 1.
Remedy:
Replace the main board {Pr(MB) -024}. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
Replace the main board {Pr(MB) -024}. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
Replace the main board {Pr(MB) -024}. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
Replace the main board {Pr(MB) -024}. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
Replace the main board {Pr(MB) -024}. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
Replace the main board {Pr(MB) -024}. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
Replace the main board {Pr(MB) -024}. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
Replace the main board {Pr(MB) -024}. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
Replace the main board {Pr(MB) -024}. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
The setting of hardware or software may be not performed correctly. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
(1) Check the DIP switch setting of EL350:PR(CR) -008/RP500:WK-7036 board.
(2) EL350:PR(CR) -008/RP500:WK-7036 board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
(1) Check the DIP switch setting of EL350:PR(CR) -008/RP500:WK-7036 board.
(2) EL350:PR(CR) -008/RP500:WK-7036 board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
(1) Check the DIP switch setting of EL350:PR(CR) -008/RP500:WK-7036 board.
(2) EL350:PR(CR) -008/RP500:WK-7036 board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
(1) Check the DIP switch setting of EL350:PR(CR) -008/RP500:WK-7036 board.
(2) EL350:PR(CR) -008/RP500:WK-7036 board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
(1) Check the DIP switch setting of EL350:PR(CR) -008/RP500:WK-7036 board.
(2) EL350:PR(CR) -008/RP500:WK-7036 board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
(1) Check the DIP switch setting of EL350:PR(CR) -008/RP500:WK-7036 board.
(2) EL350:PR(CR) -008/RP500:WK-7036 board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
(1) Check the DIP switch setting of EL350:PR(CR) -008/RP500:WK-7036 board.
(2) EL350:PR(CR) -008/RP500:WK-7036 board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
(1) Check the DIP switch setting of EL350:PR(CR) -008/RP500:WK-7036 board.
(2) EL350:PR(CR) -008/RP500:WK-7036 board may be broken. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
(1) Check the DIP switch setting of EL350:PR(CR) -008/RP500:WK-7036 board.
(2) EL350:PR(CR) -008/RP500:WK-7036 board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
Confirm the following content.
(1) The encoder cable be not damaged?
(2) Isn’t there loosening of the screw of the encoder cable connection terminal block?
When there are a disconnection of the encoder cable or loosening of the screw, the wire feeding speed quickens abnormally, and it becomes an abnormal amount of feeding. Replace the encoder cable or fasten the screw of the terminal block.
(3) Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 2.
Remedy:
Confirm the following content.
(1) The encoder cable be not damaged?
(2) Isn’t there loosening of the screw of the encoder cable connection terminal block?
When there are a disconnection of the encoder cable or loosening of the screw, the wire feeding speed quickens abnormally, and it becomes an abnormal amount of feeding. Replace the encoder cable or fasten the screw of the terminal block.
(3) Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 3.
Remedy:
Confirm the following content.
(1) The encoder cable be not damaged?
(2) Isn’t there loosening of the screw of the encoder cable connection terminal block?
When there are a disconnection of the encoder cable or loosening of the screw, the wire feeding speed quickens abnormally, and it becomes an abnormal amount of feeding. Replace the encoder cable or fasten the screw of the terminal block.
(3) Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 4.
Remedy:
Confirm the following content.
(1) The encoder cable be not damaged?
(2) Isn’t there loosening of the screw of the encoder cable connection terminal block?
When there are a disconnection of the encoder cable or loosening of the screw, the wire feeding speed quickens abnormally, and it becomes an abnormal amount of feeding. Replace the encoder cable or fasten the screw of the terminal block.
(3) Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 5.
Remedy:
Confirm the following content.
(1) The encoder cable be not damaged?
(2) Isn’t there loosening of the screw of the encoder cable connection terminal block?
When there are a disconnection of the encoder cable or loosening of the screw, the wire feeding speed quickens abnormally, and it becomes an abnormal amount of feeding. Replace the encoder cable or fasten the screw of the terminal block.
(3) Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 6.
Remedy:
Confirm the following content.
(1) The encoder cable be not damaged?
(2) Isn’t there loosening of the screw of the encoder cable connection terminal block?
When there are a disconnection of the encoder cable or loosening of the screw, the wire feeding speed quickens abnormally, and it becomes an abnormal amount of feeding. Replace the encoder cable or fasten the screw of the terminal block.
(3) Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 7.
Remedy:
Confirm the following content.
(1) The encoder cable be not damaged?
(2) Isn’t there loosening of the screw of the encoder cable connection terminal block?
When there are a disconnection of the encoder cable or loosening of the screw, the wire feeding speed quickens abnormally, and it becomes an abnormal amount of feeding. Replace the encoder cable or fasten the screw of the terminal block.
(3) Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 8.
Remedy:
Confirm the following content.
(1) The encoder cable be not damaged?
(2) Isn’t there loosening of the screw of the encoder cable connection terminal block?
When there are a disconnection of the encoder cable or loosening of the screw, the wire feeding speed quickens abnormally, and it becomes an abnormal amount of feeding. Replace the encoder cable or fasten the screw of the terminal block.
(3) Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Sub code : Error No. from welder.
Remedy:
Confirm the following content.
(1) The encoder cable be not damaged?
(2) Isn’t there loosening of the screw of the encoder cable connection terminal block?
When there are a disconnection of the encoder cable or loosening of the screw, the wire feeding speed quickens abnormally, and it becomes an abnormal amount of feeding. Replace the encoder cable or fasten the screw of the terminal block.
(3) Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
The status of dip switch for encoder circuit is different to the encoder of the feeder motor.
Remedy:
(1) Confirm the feeder motor type.
(2) Check the C parameter for feeder motor is correct.
(3) Check the dip switch SW700 on the Main board Pr(MB).
Description:
Error from welder 1.
Remedy:
Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 2.
Remedy:
Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 3.
Remedy:
Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 4.
Remedy:
Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 5.
Remedy:
Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 6.
Remedy:
Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 7.
Remedy:
Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 8.
Remedy:
Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Sub code : Error No. from welder.
Remedy:
Check if the wire load becomes heavy. Make sure that the torch cable and conduit cable are not bent excessively.
Description:
Error from welder 1.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
The data may not have been correctly saved when the welding conditions are recorded because of a power failure, etc. Reset the system after saving the changed parameters. (See the manual of MOTOWELD “4.2.10 System Reset”)
If the error occurs again, the board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
Check again the operation timing or signal cable connections. The same error may occur at momentary power failure.
Description:
Error from welder 2.
Remedy:
Check again the operation timing or signal cable connections. The same error may occur at momentary power failure.
Description:
Error from welder 3.
Remedy:
Check again the operation timing or signal cable connections. The same error may occur at momentary power failure.
Description:
Error from welder 4.
Remedy:
Check again the operation timing or signal cable connections. The same error may occur at momentary power failure.
Description:
Error from welder 5.
Remedy:
Check again the operation timing or signal cable connections. The same error may occur at momentary power failure.
Description:
Error from welder 6.
Remedy:
Check again the operation timing or signal cable connections. The same error may occur at momentary power failure.
Description:
Error from welder 7.
Remedy:
Check again the operation timing or signal cable connections. The same error may occur at momentary power failure.
Description:
Error from welder 8.
Remedy:
Check again the operation timing or signal cable connections. The same error may occur at momentary power failure.
Description:
Sub code : Error No. from welder.
Remedy:
Check again the operation timing or signal cable connections. The same error may occur at momentary power failure.
Description:
Error from welder 1.
Remedy:
Select a correct welding process in the using the welding user file.
Description:
Error from welder 2.
Remedy:
Select a correct welding process in the using the welding user file.
Description:
Error from welder 3.
Remedy:
Select a correct welding process in the using the welding user file.
Description:
Error from welder 4.
Remedy:
Select a correct welding process in the using the welding user file.
Description:
Error from welder 5.
Remedy:
Select a correct welding process in the using the welding user file.
Description:
Error from welder 6.
Remedy:
Select a correct welding process in the using the welding user file.
Description:
Error from welder 7.
Remedy:
Select a correct welding process in the using the welding user file.
Description:
Error from welder 8.
Remedy:
Select a correct welding process in the using the welding user file.
Description:
Sub code : Error No. from welder.
Remedy:
Select a correct welding process in the using the welding user file.
Description:
Error from welder 1.
Remedy:
(1) Check if the voltage detection wire is connected. Check to confirm that the welding voltage sensing cable select switch is set to “Base Metal”.
The use of MOTOWELD-RP500/EL350:
Check to confirm that the voltage sensing cable is connected between the base metal and the terminal block TB2 7.
The use of other MOTOWELD welders:
Check to confirm that the base metal-side welding voltage sensing cable connects between the base metal and the welding power source via wire feeder cable.
(2) Check to confirm that the contact chip and the welding work are not in contact. Cancel the contact if any, and weld them.
(3) Temporary power failure may have occurred.
(4) When the welding voltage sensing cable is used, please connect the welding voltage sensing cable to the base metal.
(5) When the AC unit used, a weldingpower source output cable, please confirm whether the output cable of the wiring of the AC unit is not a mistake.
(6) When the AC unit used, please make sure that the power of the AC unit is turned on.
Description:
Error from welder 2.
Remedy:
(1) Check if the voltage detection wire is connected. Check to confirm that the welding voltage sensing cable select switch is set to “Base Metal”.
The use of MOTOWELD-RP500/EL350:
Check to confirm that the voltage sensing cable is connected between the base metal and the terminal block TB2 7.
The use of other MOTOWELD welders:
Check to confirm that the base metal-side welding voltage sensing cable connects between the base metal and the welding power source via wire feeder cable.
(2) Check to confirm that the contact chip and the welding work are not in contact. Cancel the contact if any, and weld them.
(3) Temporary power failure may have occurred.
(4) When the welding voltage sensing cable is used, please connect the welding voltage sensing cable to the base metal.
(5) When the AC unit used, a weldingpower source output cable, please confirm whether the output cable of the wiring of the AC unit is not a mistake.
(6) When the AC unit used, please make sure that the power of the AC unit is turned on.
Description:
Error from welder 3.
Remedy:
(1) Check if the voltage detection wire is connected. Check to confirm that the welding voltage sensing cable select switch is set to “Base Metal”.
The use of MOTOWELD-RP500/EL350:
Check to confirm that the voltage sensing cable is connected between the base metal and the terminal block TB2 7.
The use of other MOTOWELD welders:
Check to confirm that the base metal-side welding voltage sensing cable connects between the base metal and the welding power source via wire feeder cable.
(2) Check to confirm that the contact chip and the welding work are not in contact. Cancel the contact if any, and weld them.
(3) Temporary power failure may have occurred.
(4) When the welding voltage sensing cable is used, please connect the welding voltage sensing cable to the base metal.
(5) When the AC unit used, a weldingpower source output cable, please confirm whether the output cable of the wiring of the AC unit is not a mistake.
(6) When the AC unit used, please make sure that the power of the AC unit is turned on.
Description:
Error from welder 4.
Remedy:
(1) Check if the voltage detection wire is connected. Check to confirm that the welding voltage sensing cable select switch is set to “Base Metal”.
The use of MOTOWELD-RP500/EL350:
Check to confirm that the voltage sensing cable is connected between the base metal and the terminal block TB2 7.
The use of other MOTOWELD welders:
Check to confirm that the base metal-side welding voltage sensing cable connects between the base metal and the welding power source via wire feeder cable.
(2) Check to confirm that the contact chip and the welding work are not in contact. Cancel the contact if any, and weld them.
(3) Temporary power failure may have occurred.
(4) When the welding voltage sensing cable is used, please connect the welding voltage sensing cable to the base metal.
(5) When the AC unit used, a weldingpower source output cable, please confirm whether the output cable of the wiring of the AC unit is not a mistake.
(6) When the AC unit used, please make sure that the power of the AC unit is turned on.
Description:
Error from welder 5.
Remedy:
(1) Check if the voltage detection wire is connected. Check to confirm that the welding voltage sensing cable select switch is set to “Base Metal”.
The use of MOTOWELD-RP500/EL350:
Check to confirm that the voltage sensing cable is connected between the base metal and the terminal block TB2 7.
The use of other MOTOWELD welders:
Check to confirm that the base metal-side welding voltage sensing cable connects between the base metal and the welding power source via wire feeder cable.
(2) Check to confirm that the contact chip and the welding work are not in contact. Cancel the contact if any, and weld them.
(3) Temporary power failure may have occurred.
(4) When the welding voltage sensing cable is used, please connect the welding voltage sensing cable to the base metal.
(5) When the AC unit used, a weldingpower source output cable, please confirm whether the output cable of the wiring of the AC unit is not a mistake.
(6) When the AC unit used, please make sure that the power of the AC unit is turned on.
Description:
Error from welder 6.
Remedy:
(1) Check if the voltage detection wire is connected. Check to confirm that the welding voltage sensing cable select switch is set to “Base Metal”.
The use of MOTOWELD-RP500/EL350:
Check to confirm that the voltage sensing cable is connected between the base metal and the terminal block TB2 7.
The use of other MOTOWELD welders:
Check to confirm that the base metal-side welding voltage sensing cable connects between the base metal and the welding power source via wire feeder cable.
(2) Check to confirm that the contact chip and the welding work are not in contact. Cancel the contact if any, and weld them.
(3) Temporary power failure may have occurred.
(4) When the welding voltage sensing cable is used, please connect the welding voltage sensing cable to the base metal.
(5) When the AC unit used, a weldingpower source output cable, please confirm whether the output cable of the wiring of the AC unit is not a mistake.
(6) When the AC unit used, please make sure that the power of the AC unit is turned on.
Description:
Error from welder 7.
Remedy:
(1) Check if the voltage detection wire is connected. Check to confirm that the welding voltage sensing cable select switch is set to “Base Metal”.
The use of MOTOWELD-RP500/EL350:
Check to confirm that the voltage sensing cable is connected between the base metal and the terminal block TB2 7.
The use of other MOTOWELD welders:
Check to confirm that the base metal-side welding voltage sensing cable connects between the base metal and the welding power source via wire feeder cable.
(2) Check to confirm that the contact chip and the welding work are not in contact. Cancel the contact if any, and weld them.
(3) Temporary power failure may have occurred.
(4) When the welding voltage sensing cable is used, please connect the welding voltage sensing cable to the base metal.
(5) When the AC unit used, a weldingpower source output cable, please confirm whether the output cable of the wiring of the AC unit is not a mistake.
(6) When the AC unit used, please make sure that the power of the AC unit is turned on.
Description:
Error from welder 8.
Remedy:
(1) Check if the voltage detection wire is connected. Check to confirm that the welding voltage sensing cable select switch is set to “Base Metal”.
The use of MOTOWELD-RP500/EL350:
Check to confirm that the voltage sensing cable is connected between the base metal and the terminal block TB2 7.
The use of other MOTOWELD welders:
Check to confirm that the base metal-side welding voltage sensing cable connects between the base metal and the welding power source via wire feeder cable.
(2) Check to confirm that the contact chip and the welding work are not in contact. Cancel the contact if any, and weld them.
(3) Temporary power failure may have occurred.
(4) When the welding voltage sensing cable is used, please connect the welding voltage sensing cable to the base metal.
(5) When the AC unit used, a weldingpower source output cable, please confirm whether the output cable of the wiring of the AC unit is not a mistake.
(6) When the AC unit used, please make sure that the power of the AC unit is turned on.
Description:
Sub code : Error No. from welder.
Remedy:
(1) Check if the voltage detection wire is connected. Check to confirm that the welding voltage sensing cable select switch is set to “Base Metal”.
The use of MOTOWELD-RP500/EL350:
Check to confirm that the voltage sensing cable is connected between the base metal and the terminal block TB2 7.
The use of other MOTOWELD welders:
Check to confirm that the base metal-side welding voltage sensing cable connects between the base metal and the welding power source via wire feeder cable.
(2) Check to confirm that the contact chip and the welding work are not in contact. Cancel the contact if any, and weld them.
(3) Temporary power failure may have occurred.
(4) When the welding voltage sensing cable is used, please connect the welding voltage sensing cable to the base metal.
(5) When the AC unit used, a weldingpower source output cable, please confirm whether the output cable of the wiring of the AC unit is not a mistake.
(6) When the AC unit used, please make sure that the power of the AC unit is turned on.
Description:
Error from welder 1.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
Replace the IGBT device (Part code AJ0EL3870).
Description:
Error from welder 2.
Remedy:
Replace the IGBT device (Part code AJ0EL3870).
Description:
Error from welder 3.
Remedy:
Replace the IGBT device (Part code AJ0EL3870).
Description:
Error from welder 4.
Remedy:
Replace the IGBT device (Part code AJ0EL3870).
Description:
Error from welder 5.
Remedy:
Replace the IGBT device (Part code AJ0EL3870).
Description:
Error from welder 6.
Remedy:
Replace the IGBT device (Part code AJ0EL3870).
Description:
Error from welder 7.
Remedy:
Replace the IGBT device (Part code AJ0EL3870).
Description:
Error from welder 8.
Remedy:
Replace the IGBT device (Part code AJ0EL3870).
Description:
Sub code : Error No. from welder.
Remedy:
Replace the IGBT device (Part code AJ0EL3870).
Description:
Error from welder 1.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Auxiliary circuit overcurrent
Remedy:
The board may be broken. Contact your YASKAWA representative.
Description:
Auxiliary circuit instantaneous overcurrent
Remedy:
The board may be broken. Contact your Yaskawa representative.
Description:
Lack of auxiliary circuit current
Remedy:
The board may be broken. Contact your Yaskawa representative.
Description:
Error from welder 1.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 2.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 3.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 4.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 5.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 6.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 7.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 8.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Sub code : Error No. from welder.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 1.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 2.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 3.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 4.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 5.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 6.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 7.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 8.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Sub code : Error No. from welder.
Remedy:
(1) Check if the selection of motor is correct, or confirm the settings of C parameter C09.
(2) Check that the welding wire does not slip, or the wire is fed as instructed by the feeding command.
(3) Check that the wire stick out is not excessively short or long.
(4) Check that the range set in C parameter C29 is not too narrow.
(5) Check if the wire, shielding, etc. are correctly set.
Description:
Error from welder 1.
Remedy:
(1) Check that short-circuit or the earth grounded of the output cable.
(2) May be power circuit broken. Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
(1) Check that short-circuit or the earth grounded of the output cable.
(2) May be power circuit broken. Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
(1) Check that short-circuit or the earth grounded of the output cable.
(2) May be power circuit broken. Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
(1) Check that short-circuit or the earth grounded of the output cable.
(2) May be power circuit broken. Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
(1) Check that short-circuit or the earth grounded of the output cable.
(2) May be power circuit broken. Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
(1) Check that short-circuit or the earth grounded of the output cable.
(2) May be power circuit broken. Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
(1) Check that short-circuit or the earth grounded of the output cable.
(2) May be power circuit broken. Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
(1) Check that short-circuit or the earth grounded of the output cable.
(2) May be power circuit broken. Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
(1) Check that short-circuit or the earth grounded of the output cable.
(2) May be power circuit broken. Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 2.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 3.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 4.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 5.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 6.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 7.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 8.
Remedy:
Contact your YASKAWA representative.
Description:
Sub code : Error No. from welder.
Remedy:
Contact your YASKAWA representative.
Description:
Error from welder 1.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 2.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 3.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 4.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 5.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 6.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 7.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 8.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Sub code : Error No. from welder.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 1.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 2.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 3.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 4.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 5.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 6.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 7.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 8.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Sub code : Error No. from welder.
Remedy:
The use of MOTOWELD-RP500:
Replace the switching power supply unit (Service parts code:35015612200) or the Main board (Service parts code:AJ0RP3024). Or, please change two of them.
The use of MOTOWELD-RL350:
Replace the Interface board (Service parts code: UNIT-Pr (IF)-008B) or the Main board (Service parts code: UNIT-Pr (MB)-030). Or, please change two of them.
Description:
Error from welder 1.
Remedy:
Confirm the welding process setting in the welding user file.
Description:
Error from welder 2.
Remedy:
Confirm the welding process setting in the welding user file.
Description:
Error from welder 3.
Remedy:
Confirm the welding process setting in the welding user file.
Description:
Error from welder 4.
Remedy:
Confirm the welding process setting in the welding user file.
Description:
Error from welder 5.
Remedy:
Confirm the welding process setting in the welding user file.
Description:
Error from welder 6.
Remedy:
Confirm the welding process setting in the welding user file.
Description:
Error from welder 7.
Remedy:
Confirm the welding process setting in the welding user file.
Description:
Error from welder 8.
Remedy:
Confirm the welding process setting in the welding user file.
Description:
A wrong welding process is set in the welding user file.
Remedy:
Confirm the welding process setting in the welding user file.
Description:
A welding type is not set in a user file of the MOTOWELD.
Remedy:
Set a welding type to user file of MOTOWELD. The user file can setup in the editor screen for ARC START CONDITION FILE or ARC END CONDITION FILE of the robot controller.
Description:
The version of the data base is not suitable for the software of the welding power source.
Remedy:
Load the suitable database.
Description:
The version information of the PLD on the main board Pr(MB) is wrong.
Remedy:
Replace the main board (Service parts code: UNIT-Pr (MB)-030).
Contact your YASKAWA representative
Description:
The version of the firmware of front panel is not suitable for the software of the main board Pr(MB).
Remedy:
Replace the main board (Service parts code: UNIT-Pr (MB)-030).
Contact your YASKAWA representative
Description:
The check sum of the PLD on the main board Pr(MB) is wrong.
Remedy:
Replace the main board (Service parts code: UNIT-Pr (MB)-030).
Contact your YASKAWA representative
Description:
The program or data base was load by the ethernet.
Remedy:
Reboot the power source.
Description:
The check sum error of loading data.
Remedy:
(1) Do not turn off the power source and reload the data.
(2) In case of turn off and reboot was OK, reload the data.
(3) In case of turn off and reboot was NG, load the data by special loading tool.
(4) Other case of step 1, 2, 3, replace the main board Pr(MB)-030.
Description:
Watch dog error of the PLD.
Remedy:
(1) reboot the power source.
(2) Replace the main board {Pr(MB) -030}.
Contact your YASKAWA representative
Description:
The machine type is wrong.
Remedy:
(1) Check the connection between front panel and main board.
(2) Check the status of dip switch (SW301) on the front panel.
(3) Replace the front panel.
(4) Replace the main board.
Description:
The current class 350A / 500A setting is wrong.
Remedy:
(1) Confirm the power source class which of 350A or 500A.
(2) Switch a status of dip switch SW600 which of 350A or 500A.
(3) Change the software which for correct current class.
Description:
The count of shortcircuit is largely decreased.(The bead NG)
Remedy:
(1) Check that setting current is not too high.
(2) Check that range set in C parameter C62 is not too narrow.
(3) Check that the wire stick out is not excessively short.
Description:
AC unit temperature anomaly
Remedy:
(1) Check the ambient temperature(45 degrees or below) and the usage rate(60%)
(2) Check for no dirt or clogging in the dust-proof filter. Check or replace as needed.
(3) Make sure thermal guard of AC unit is not broken.
Description:
AC unit overvoltage
Remedy:
(1) Check the usage rate (60%)
(2) Check the length of the power cable is round-trip less than 20m.
(3) Check a power cable does not wind up a coil.
Description:
AC welding method setting error
Remedy:
It can not AC welding for the AC unit is not connected.
Description:
SERVO PACK ALARM (EAGL)
Remedy:
(1) A.720: Overload (maximum continuous)
Description:
no Prg
Sub code[1**] shows the error code of Fronius power source
1 :main error code
** :sub error code
Remedy:
Select a pre-programmed program .
Confirm the Fronius’s manual.
Description:
ts1
Sub code[2**] shows the error code of Fronius power source
2 :main error code
** :sub error code
Remedy:
Allow the machine to cool .
Confirm the Fronius’s manual.
Description:
ts2
Sub code[3**] shows the error code of Fronius power source
3 :main error code
** :sub error code
Remedy:
Allow the machine to cool .
Confirm the Fronius’s manual.
Description:
ts3
Sub code[4**] shows the error code of Fronius power source
4 :main error code
** :sub error code
Remedy:
Allow the machine to cool .
Confirm the Fronius’s manual.
Description:
tp1
Sub code[5**] shows the error code of Fronius power source
5 :main error code
** :sub error code
Remedy:
Allow the machine to cool .
Confirm the Fronius’s manual.
Description:
tp2
Sub code[6**] shows the error code of Fronius power source
6 :main error code
** :sub error code
Remedy:
Allow the machine to cool .
Confirm the Fronius’s manual.
Description:
tp3
Sub code[7**] shows the error code of Fronius power source
7 :main error code
** :sub error code
Remedy:
Allow the machine to cool .
Confirm the Fronius’s manual.
Description:
tp4
Sub code[8**] shows the error code of Fronius power source
8 :main error code
** :sub error code
Remedy:
Allow the machine to cool .
Confirm the Fronius’s manual.
Description:
tp5
Sub code[9**] shows the error code of Fronius power source
9 :main error code
** :sub error code
Remedy:
Allow the machine to cool .
Confirm the Fronius’s manual.
Description:
tp6
Sub code[10**] shows the error code of Fronius power source
10 :main error code
** :sub error code
Remedy:
Allow the machine to cool .
Confirm the Fronius’s manual.
Description:
Errtf1
Sub code[11**] shows the error code of Fronius power source
11 :main error code
** :sub error code
Remedy:
Change the thermosensor on the sec. side.
Confirm the Fronius’s manual.
Description:
Errtf2
Sub code[12**] shows the error code of Fronius power source
12 :main error code
** :sub error code
Remedy:
Change the thermosensor on the sec. side.
Confirm the Fronius’s manual.
Description:
Errtf3
Sub code[13**] shows the error code of Fronius power source
13 :main error code
** :sub error code
Remedy:
Check cable tree of temperature sensors.
Confirm the Fronius’s manual.
Description:
Errtf4
Sub code[14**] shows the error code of Fronius power source
14 :main error code
** :sub error code
Remedy:
Only for MagicWave power source.
Confirm the Fronius’s manual.
Description:
Errtf5
Sub code[15**] shows the error code of Fronius power source
15 :main error code
** :sub error code
Remedy:
Check cable tree of temperature sensors.
Confirm the Fronius’s manual.
Description:
Errtf6
Sub code[16**] shows the error code of Fronius power source
16 :main error code
** :sub error code
Remedy:
Change BPS pc-board.
Confirm the Fronius’s manual.
Description:
DSPE05
Sub code[17**] shows the error code of Fronius power source
17 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
ErrbPS
Sub code[18**] shows the error code of Fronius power source
18 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board or otherwise change the BPS board.
Confirm the Fronius’s manual.
Description:
Err IP
Sub code[19**] shows the error code of Fronius power source
19 :main error code
** :sub error code
Remedy:
Change the BPS board.
Change the secondary diode.
Change the welding transformer.
Confirm the Fronius’s manual.
Description:
DSPAxx
Sub code[20**] shows the error code of Fronius power source
20 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
DSPExx
Sub code[21**] shows the error code of Fronius power source
21 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
ErrEPF
Sub code[22**] shows the error code of Fronius power source
22 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
Err23.x
Sub code[23**] shows the error code of Fronius power source
23 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
Err24.x
Sub code[24**] shows the error code of Fronius power source
24 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
Err25.x
Sub code[25**] shows the error code of Fronius power source
25 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual
Description:
Err26.x
Sub code[26**] shows the error code of Fronius power source
26 :main error code
** :sub error code
Remedy:
Check whether the CfgMem has good contact to the connecting cables and in the plug.
Re-crimp if necessary.
If this does not help, remove and send to Fronius Austria, together with details of the series number of the machine.
Confirm the Fronius’s manual
Description:
Err027
Sub code[27**] shows the error code of Fronius power source
27 :main error code
** :sub error code
Remedy:
Measure the +24VDC of NT 24.
Confirm the Fronius’s manual
Description:
Err028
Sub code[28**] shows the error code of Fronius power source
28 :main error code
** :sub error code
Remedy:
Change the cooling-unit temperature sensor.
Confirm the Fronius’s manual
Description:
DSPC
Sub code[29**] shows the error code of Fronius power source
29 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
EFd
Sub code[30**] shows the error code of Fronius power source
30 :main error code
** :sub error code
Remedy:
Check the wirefeed system.
Confirm the Fronius’s manual.
Description:
Err31
Sub code[31**] shows the error code of Fronius power source
31 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
EcF
Sub code[32**] shows the error code of Fronius power source
32 :main error code
** :sub error code
Remedy:
Install correct primary BPS power module.
Confirm the Fronius’s manual.
Description:
tSt
Sub code[33**] shows the error code of Fronius power source
33 :main error code
** :sub error code
Remedy:
Allow the machine to cool .
Confirm the Fronius’s manual.
Description:
Errtf7
Sub code[34**] shows the error code of Fronius power source
34 :main error code
** :sub error code
Remedy:
Change the UST board.
Confirm the Fronius’s manual.
Description:
DSP KL
Sub code[35**] shows the error code of Fronius power source
35 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
DSPnSy
Sub code[36**] shows the error code of Fronius power source
36 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board
Confirm the Fronius’s manual
Description:
US POL
Sub code[37**] shows the error code of Fronius power source
37 :main error code
** :sub error code
Remedy:
Change over the polarity of the two cables otherwise change the UST board
Confirm the Fronius’s manual
Description:
-Stop-
Sub code[38**] shows the error code of Fronius power source
38 :main error code
** :sub error code
Remedy:
Deactivate the -Stop- by input -RobotReady- and activate briefly -SourceErrorReset-.
Confirm the Fronius’s manual.
Description:
NoH2O
Sub code[39**] shows the error code of Fronius power source
39 :main error code
** :sub error code
Remedy:
Check the coolant level and (if appropriate) the coolant return-flow rate
If necessary, clean the coolant filter.
Rate-of-flow watchdog may be defective.
Confirm the Fronius’s manual.
Description:
ErrLic
Sub code[40**] shows the error code of Fronius power source
40 :main error code
** :sub error code
Remedy:
Confirm the Fronius’s manual.
Description:
unknown
Sub code[41**] shows the error code of Fronius power source
41 :main error code
** :sub error code
Remedy:
OR NOT IN USE
Confirm the Fronius’s manual.
Description:
unknown
Sub code[42**] shows the error code of Fronius power source
42 :main error code
** :sub error code
Remedy:
OR NOT IN USE
Confirm the Fronius’s manual.
Description:
unknown
Sub code[43**] shows the error code of Fronius power source
43 :main error code
** :sub error code
Remedy:
OR NOT IN USE
Confirm the Fronius’s manual.
Description:
unknown
Sub code[44**] shows the error code of Fronius power source
44 :main error code
** :sub error code
Remedy:
OR NOT IN USE
Confirm the Fronius’s manual.
Description:
unknown
Sub code[45**] shows the error code of Fronius power source
45 :main error code
** :sub error code
Remedy:
OR NOT IN USE
Confirm the Fronius’s manual.
Description:
unknown
Sub code[46**] shows the error code of Fronius power source
46 :main error code
** :sub error code
Remedy:
OR NOT IN USE
Confirm the Fronius’s manual.
Description:
unknown
Sub code[47**] shows the error code of Fronius power source
47 :main error code
** :sub error code
Remedy:
OR NOT IN USE
Confirm the Fronius’s manual.
Description:
unknown
Sub code[48**] shows the error code of Fronius power source
48 :main error code
** :sub error code
Remedy:
OR NOT IN USE
Confirm the Fronius’s manual.
Description:
Err049
Sub code[49**] shows the error code of Fronius power source
49 :main error code
** :sub error code
Remedy:
Check the mains power supply .
Check all 3 phases.
Confirm the Fronius’s manual.
Description:
Err050
Sub code[50**] shows the error code of Fronius power source
50 :main error code
** :sub error code
Remedy:
Disconnect NT60 or change/check NT24/UST/BPS/intermediate circuit capacitors.
Confirm the Fronius’s manual.
Description:
Err051
Sub code[51**] shows the error code of Fronius power source
51 :main error code
** :sub error code
Remedy:
Mains voltage too low or NT 24 defective.
Confirm the Fronius’s manual.
Description:
Err052
Sub code[52**] shows the error code of Fronius power source
52 :main error code
** :sub error code
Remedy:
Mains voltage too high or NT 24 defective.
Confirm the Fronius’s manual.
Description:
ErrPE
Sub code[53**] shows the error code of Fronius power source
53 :main error code
** :sub error code
Remedy:
Low-resistance connection between secondary and machine housing find out the cause.
Confirm the Fronius’s manual.
Description:
Err054
Sub code[54**] shows the error code of Fronius power source
54 :main error code
** :sub error code
Remedy:
Increase the bbc (burn-back control)
Switch off “Wire stick " in the set-up menu
After the end of welding, make sure that the wire does not collide with the workpiece when the torch is retracted.
Confirm the Fronius’s manual.
Description:
NoIGn
Sub code[55**] shows the error code of Fronius power source
55 :main error code
** :sub error code
Remedy:
Set a lower Ito value
Keep the torch stand-off distance smaller before ignition.
Confirm the Fronius’s manual.
Description:
Err056
Sub code[56**] shows the error code of Fronius power source
56 :main error code
** :sub error code
Remedy:
Check how much wire is left on the spool
If necessary, change the spool.
Confirm the Fronius’s manual.
Description:
NoGAS
Sub code[57**] shows the error code of Fronius power source
57 :main error code
** :sub error code
Remedy:
Check what volume of gas is still available.
Confirm the Fronius’s manual.
Description:
NoArc
Sub code[58**] shows the error code of Fronius power source
58 :main error code
** :sub error code
Remedy:
Check the seam.
Confirm the Fronius’s manual.
Description:
Err059
Sub code[59**] shows the error code of Fronius power source
59 :main error code
** :sub error code
Remedy:
Confirm the Fronius’s manual.
Description:
Err060
Sub code[60**] shows the error code of Fronius power source
60 :main error code
** :sub error code
Remedy:
Confirm the Fronius’s manual.
Description:
ErrArc
Sub code[61**] shows the error code of Fronius power source
61 :main error code
** :sub error code
Remedy:
Confirm the Fronius’s manual.
Description:
Err062
Sub code[62**] shows the error code of Fronius power source
62 :main error code
** :sub error code
Remedy:
Allow the machine to cool .
Confirm the Fronius’s manual.
Description:
EIF
Sub code[63**] shows the error code of Fronius power source
63 :main error code
** :sub error code
Remedy:
Check the interface configuration.
Confirm the Fronius’s manual.
Description:
Errtf8
Sub code[64**] shows the error code of Fronius power source
64 :main error code
** :sub error code
Remedy:
Change the thermosensor of the cooling unit.
Confirm the Fronius’s manual.
Description:
hotH2O
Sub code[65**] shows the error code of Fronius power source
65 :main error code
** :sub error code
Remedy:
Cool down the coolingliquid.
Confirm the Fronius’s manual.
Description:
tJo
Sub code[66**] shows the error code of Fronius power source
66 :main error code
** :sub error code
Remedy:
Allow the JobMaster torch to cool .
Confirm the Fronius’s manual.
Description:
ErrtJo
Sub code[67**] shows the error code of Fronius power source
67 :main error code
** :sub error code
Remedy:
Change JobMaster pc-board.
Confirm the Fronius’s manual.
Description:
Err068
Sub code[68**] shows the error code of Fronius power source
68 :main error code
** :sub error code
Remedy:
Confirm the Fronius’s manual.
Description:
Err069
Sub code[69**] shows the error code of Fronius power source
69 :main error code
** :sub error code
Remedy:
New welding start.
Confirm the Fronius’s manual.
Description:
Err70
Sub code[70**] shows the error code of Fronius power source
70 :main error code
** :sub error code
Remedy:
Check gas.
Confirm the Fronius’s manual.
Description:
Err71
Sub code[71**] shows the error code of Fronius power source
71 :main error code
** :sub error code
Remedy:
Check the welding seam.
Confirm the Fronius’s manual.
Description:
ErrCfg
Sub code[72**] shows the error code of Fronius power source
72 :main error code
** :sub error code
Remedy:
Check LHSB connection.
Confirm the Fronius’s manual.
Description:
noHost
Sub code[73**] shows the error code of Fronius power source
73 :main error code
** :sub error code
Remedy:
Check the connection between UST and RCU and the firmware.
Confirm the Fronius’s manual.
Description:
Touch
Sub code[74**] shows the error code of Fronius power source
74 :main error code
** :sub error code
Remedy:
Touch sensing mode activated - no error.
Confirm the Fronius’s manual.
Description:
Err75
Sub code[75**] shows the error code of Fronius power source
75 :main error code
** :sub error code
Remedy:
Confirm the Fronius’s manual.
Description:
unknown
Sub code[76**] shows the error code of Fronius power source
76 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
Err77
Sub code[77**] shows the error code of Fronius power source
77 :main error code
** :sub error code
Remedy:
Check the wire feeding alignment if it is smooth.
Confirm the Fronius’s manual.
Description:
E-Stop
Sub code[78**] shows the error code of Fronius power source
78 :main error code
** :sub error code
Remedy:
Close the Safety circuit and activate the Error reset.
Confirm the Fronius’s manual.
Description:
ErrU0
Sub code[79**] shows the error code of Fronius power source
79 :main error code
** :sub error code
Remedy:
Confirm the Fronius’s manual.
Description:
Err080
Sub code[80**] shows the error code of Fronius power source
80 :main error code
** :sub error code
Remedy:
Check the connection hose pack between power source and wire feeder.
Confirm the Fronius’s manual.
Description:
tP7hot
Sub code[81**] shows the error code of Fronius power source
81 :main error code
** :sub error code
Remedy:
Allow the machine to cool .
Confirm the Fronius’s manual.
Description:
ErrEHF
Sub code[82**] shows the error code of Fronius power source
82 :main error code
** :sub error code
Remedy:
Allow the external HF to cool down.
Confirm the Fronius’s manual.
Description:
PHASE
Sub code[83**] shows the error code of Fronius power source
83 :main error code
** :sub error code
Remedy:
Check the mains supply cable of the power source.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[84**] shows the error code of Fronius power source
84 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[85**] shows the error code of Fronius power source
85 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[86**] shows the error code of Fronius power source
86 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[87**] shows the error code of Fronius power source
87 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[88**] shows the error code of Fronius power source
88 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[89**] shows the error code of Fronius power source
89 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[90**] shows the error code of Fronius power source
90 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[91**] shows the error code of Fronius power source
91 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[92**] shows the error code of Fronius power source
92 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[93**] shows the error code of Fronius power source
93 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[94**] shows the error code of Fronius power source
94 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[95*] shows the error code of Fronius power source
95 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[96**] shows the error code of Fronius power source
96 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[97**] shows the error code of Fronius power source
97 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[98**] shows the error code of Fronius power source
98 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[99**] shows the error code of Fronius power source
99 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
UndOpc
Sub code[100**] shows the error code of Fronius power source
100 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
PrtFlt
Sub code[101**] shows the error code of Fronius power source
101 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
IllOpa
Sub code[102**] shows the error code of Fronius power source
102 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
IllIna
Sub code[103**] shows the error code of Fronius power source
103 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
IllBus
Sub code[104**] shows the error code of Fronius power source
104 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
Err105
Sub code[105**] shows the error code of Fronius power source
105 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
STKOVL
Sub code[106**] shows the error code of Fronius power source
106 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
STKUVL
Sub code[107**] shows the error code of Fronius power source
107 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
ErrDog
Sub code[108**] shows the error code of Fronius power source
108 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
ASSErt
Sub code[109**] shows the error code of Fronius power source
109 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
EDg 1
Sub code[110**] shows the error code of Fronius power source
110 :main error code
** :sub error code
Remedy:
Update firmware, otherwise change the UST board.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[111**] shows the error code of Fronius power source
111 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[112**] shows the error code of Fronius power source
112 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[113**] shows the error code of Fronius power source
113 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[114**] shows the error code of Fronius power source
114 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[115**] shows the error code of Fronius power source
115 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[116**] shows the error code of Fronius power source
116 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[117**] shows the error code of Fronius power source
117 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[118**] shows the error code of Fronius power source
118 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[119**] shows the error code of Fronius power source
119 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[120**] shows the error code of Fronius power source
120 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[121**] shows the error code of Fronius power source
121 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[122**] shows the error code of Fronius power source
122 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[123**] shows the error code of Fronius power source
123 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[124**] shows the error code of Fronius power source
124 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[125**] shows the error code of Fronius power source
125 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[126**] shows the error code of Fronius power source
126 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[127**] shows the error code of Fronius power source
127 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[128**] shows the error code of Fronius power source
128 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[129**] shows the error code of Fronius power source
129 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[130**] shows the error code of Fronius power source
130 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[131**] shows the error code of Fronius power source
131 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[132**] shows the error code of Fronius power source
132 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[133**] shows the error code of Fronius power source
133 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[134**] shows the error code of Fronius power source
134 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[135**] shows the error code of Fronius power source
135 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[136**] shows the error code of Fronius power source
136 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[137**] shows the error code of Fronius power source
137 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[138**] shows the error code of Fronius power source
138 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[139**] shows the error code of Fronius power source
139 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[140**] shows the error code of Fronius power source
140 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[141**] shows the error code of Fronius power source
141 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[142**] shows the error code of Fronius power source
142 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[143**] shows the error code of Fronius power source
143 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[144**] shows the error code of Fronius power source
144 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[145**] shows the error code of Fronius power source
145 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[146**] shows the error code of Fronius power source
146 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[147**] shows the error code of Fronius power source
147 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[148**] shows the error code of Fronius power source
148 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[149**] shows the error code of Fronius power source
149 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
Err150
Sub code[150**] shows the error code of Fronius power source
150 :main error code
** :sub error code
Remedy:
Check the power supply of the power source.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[151**] shows the error code of Fronius power source
151 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[152**] shows the error code of Fronius power source
152 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[153**] shows the error code of Fronius power source
153 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[154**] shows the error code of Fronius power source
154 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[155**] shows the error code of Fronius power source
155 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[156**] shows the error code of Fronius power source
156 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[157**] shows the error code of Fronius power source
157 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[158**] shows the error code of Fronius power source
158 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[159**] shows the error code of Fronius power source
159 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[160**] shows the error code of Fronius power source
160 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[161**] shows the error code of Fronius power source
161 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[162**] shows the error code of Fronius power source
162 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[163**] shows the error code of Fronius power source
163 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[164**] shows the error code of Fronius power source
164 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[165**] shows the error code of Fronius power source
165 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[166**] shows the error code of Fronius power source
166 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[167**] shows the error code of Fronius power source
167 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[168**] shows the error code of Fronius power source
168 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[169**] shows the error code of Fronius power source
169 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[170**] shows the error code of Fronius power source
170 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[171**] shows the error code of Fronius power source
171 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[172**] shows the error code of Fronius power source
172 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[173**] shows the error code of Fronius power source
173 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[174**] shows the error code of Fronius power source
174 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[175**] shows the error code of Fronius power source
175 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[176**] shows the error code of Fronius power source
176 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[177**] shows the error code of Fronius power source
177 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[178**] shows the error code of Fronius power source
178 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[179**] shows the error code of Fronius power source
179 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[180**] shows the error code of Fronius power source
180 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[81**] shows the error code of Fronius power source
181 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[182**] shows the error code of Fronius power source
182 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[183**] shows the error code of Fronius power source
183 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[184**] shows the error code of Fronius power source
184 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[185**] shows the error code of Fronius power source
185 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[186**] shows the error code of Fronius power source
186 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[187**] shows the error code of Fronius power source
187 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[188**] shows the error code of Fronius power source
188 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[189**] shows the error code of Fronius power source
189 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[190**] shows the error code of Fronius power source
190 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[191**] shows the error code of Fronius power source
191 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[192**] shows the error code of Fronius power source
192 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[193**] shows the error code of Fronius power source
193 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[194**] shows the error code of Fronius power source
194 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[195**] shows the error code of Fronius power source
195 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[196**] shows the error code of Fronius power source
196 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[197**] shows the error code of Fronius power source
197 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[198**] shows the error code of Fronius power source
198 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[199**] shows the error code of Fronius power source
199 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
unknown
Sub code[200**] shows the error code of Fronius power source
200 :main error code
** :sub error code
Remedy:
OR NOT IN USE.
Confirm the Fronius’s manual.
Description:
Sub Code: The duplicated gun number
Remedy:
Check the settings for gun numbers.
Description:
Sub Code: Gun number
Remedy:
Check the following settings.
-ALLOWABLE WIDTH OF ERROR (Is the width too narrow?)
Description:
The setting of the first pressure specified in PRESSURE ERROR DETECT FILE is abnormal.
Remedy:
Set an appropriate value for the first pressure.
Description:
The setting of the second pressure specified in PRESSURE ERROR DETECT FILE is abnormal.
Remedy:
Set the second pressure higher than the first pressure.
Description:
An instruction that does not support high speed multi-move has been executed.
Remedy:
Correct the job so that instructions that do not support high speed multi-move are not executed in the high speed multi-move section.
Description:
Failed to restart the high speed multi-move job.
Remedy:
(1) Reset the alarm, and re-select the job from [select job] window before starting the job again .
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Motion control not compatible with high speed multi-move has been executed.
Remedy:
Correct the job so that motion control not compatible with high speed multi-move is not executed in the high speed multi-move section.
Description:
Speed control that does not support high speed multi-move has been executed.
Remedy:
Correct the job so that high speed multi-move non-compliant speed control is not executed in the high speed multi-move section.
Description:
Control group that does not support high speed multi-move has been executed.
Remedy:
Correct the job so that high speed multi-move non-compliant control group is not executed in the high speed multi-move section.
Description:
Interpolation that does not support high speed multi-move has been executed.
Remedy:
Correct the job so that high speed multi-move non-compliant interpolation is not executed in the high speed multi-move section.
Description:
Function that does not support high speed multi-move has been executed.
Remedy:
Correct the job so that high speed multi-move non-compliant function is not executed in the high speed multi-move section.
Description:
An error occurred in a calculated speed by high speed multi-move
Remedy:
(1) Reset the alarm, and re-select the job from [select job] window before starting the job again .
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Tag that does not support high speed multi-move has been executed.
Remedy:
Correct the job so that high speed multi-move non-compliant tag is not executed in the high speed multi-move section.
Description:
An error occurred in a high speed multi-move data.
Remedy:
(1) Reset the alarm, and re-select the job from [select job] window before starting the job again .
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Checking high speed multi-move has failed.
Remedy:
(1) Reset the alarm, and re-select the job from [select job] window before starting the job again .
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Welder number*1000 + data number(1-400)
Remedy:
(1) Please check the welding bead.
(2) Check welding conditions, welding tip, gas flow rate, workpiece misalignment, jig etc.
(3) If the welding bead is normal and the alarm occurs frequently, please change the threshold value of weld diagnosis function.
Content:
The parameter input value is out of the allowable range.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check whether the setting is within the allowable range.
Description:
Sub Code: Signifies the physical No. of contactor in which the alarm occurred
Before performing a connection check of the wiring, turn OFF the controller power. Make sure that all the LEDs of SERVOPACK and converter are OFF, then verify that no electricity is charged using equipment such as a tester. This process may take a few minutes after shutting off the power.
Remedy:
(1) Reset the alarm.
(2) Check the connection and inserting state of the following cables and connectors.
Content:
This alarm occurs if the brake is not released when the servo turned ON.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the SDCA01 board. Save the CMOS.BIN before replacing the board to be safe.
Description:
Sub Code: Signifies the physical No. of converter in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Sub Code: Signifies the physical No. of converter in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the APU01 unit. Save the CMOS.BIN before replacing the board to be safe.
Description:
Sub Code: Signifies the physical No. of converter in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the Converter-CN556 connectors.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check that the manipulator is not moving when the servo turned ON.
Description:
Sub Code: Signifies the physical No. of converter in which the alarm occurred
Remedy:
Check if the primary power supply voltage is dropping.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
[Robot axis]
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Turn OFF the YRC1000 power for approx. 10 minutes, then turn it ON again.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
[AL-4314 occurred]
Replace the battery of the axis in which the error occurred.
[AL-1327 occurred]
Replace the battery of the axis in which the alarm occurred. If the home position of the corresponding axis is displayed as “***”, register the home position again.
AL-1327 occurs due to the battery disconnection (weak battery), causing undefined alarm data.
If the alarm doesn’t occur after turning the power OFF and then ON, there is no problem.
Content:
Encoder backup battery voltage is too low.
The voltage of the encoder backup battery is below 2.8V.
Remedy:
Replace the battery.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the following settings.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the following settings.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Adjust the gun opening.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
[Robot axis]
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Move the gun axis to another position by manual operation and then turn the servo power on again.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the tools or the mass of the workpieces.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the tools or the mass of the workpieces.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the tools or the mass of the workpieces.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the tools or the mass of the workpieces.
Content:
The total load value of all the motors connected to the converter exceeded the converter rating.
Remedy:
- Confirm that the tool and workpiece in use don’t exceed the permissible load.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
If the alarm occurs for the motor gun, check the following settings.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and insertion of the following cables and connectors.
Motor power cable
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the following settings.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R1)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R1)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R1)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R1)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R2)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R2)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R2)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R2)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R3)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R3)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R3)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R3)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R4)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R4)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R4)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R4)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R5)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R5)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R5)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R5)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R6)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R6)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R6)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R6)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R7)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R7)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R7)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R7)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R8)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the flange exceeded the specified max. speed. (R8)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R8)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Description:
The motion speed at the center of the control point exceeded the specified max. speed. (R8)
Remedy:
If the alarm occurs at the same site, set the lower motion speed around the site where the alarm occurs.
Content:
The read speed monitoring level signal is disconnected.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the speed monitor unit cables and connectors.
Content:
The speed monitor level is incorrect.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the SDCA01 board. Save the CMOS.BIN before replacing the board to be safe.
Description:
Sub Code: Signifies the axis in which the alarm occurred.
Remedy:
Check the tip dresser control parameter.
Description:
Sub Code: Signifies the physical No. of converter in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Sub Code: Signifies the axis in which the alarm occurred.
(If the alarm occurred at an axis which is driven by a common converter, all the subject axes are indicated.)
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Sub Code: Signifies the physical No. of converter in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Sub Code: Signifies the physical No. of converter in which the alarm occurred
Remedy:
Modify the primary breaker voltage to the voltage specified for the power supply on the rated label on the door of the controller.
Description:
Sub Code: Signifies the physical No. of converter in which the alarm occurred
Remedy:
Check that the air inlet or outlet is not blocked.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check if metal pieces getting into dresser blades prevent the dresser from rotating.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check if metal pieces getting into dresser blades prevent the dresser from rotating.
Content:
The deviation of X, Y, and Z-axis exceeded the allowable limit while the linear servo float was in execution.
Remedy:
(1) Check the settings for jobs.
(2) Reset the alarm.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Check the settings for jobs.
(2) Reset the alarm.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Check the limit torque of the link servo float condition file.
(2) Reset the alarm.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Check the limit torque of the link servo float condition file.
(2) Reset the alarm.
Description:
Sub Code: Signifies linear servo float condition file number in which the alarm occurred
Remedy:
(1) Check the setting file of the job and the linear servo float.
(2) Reset the alarm.
Content:
Another request of the linear servo float execution with a different tool orientation control specified was sent to an axis where the linear servo float is executing.
Remedy:
(1) Check the setting file of the job and the linear servo float.
(2) Reset the alarm.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Check the settings for jobs.
(2) Reset the alarm.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Check that the driving belt is not broken.
(2) If the driving belt is broken, replace the driving belt.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the following settings.
Description:
Sub Code: File number
Remedy:
Do not use the collision detection file for exclusive use for the SVSPOT with the SHCKSET instruction.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the settings for jobs.
Content:
The search of motor-gun equalizing function cannot be executed because no observer (including collision detection) is specified.
Remedy:
Check the settings for jobs.
Content:
The manipulator orientation at the execution of search of the motor-gun equalizing function is the orientation for the singular point.
Remedy:
Check the settings for jobs.
Content:
The pressuring instruction was executed again for the axis where pressuring is executing.
Remedy:
End the current pressuring operation, and then execute the pressuring instruction.
Description:
Sub Code: Signifies the physical No. of converter in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Content:
An error occurred in communications with the prealigner.
Remedy:
Check the connection of prealigner.
Content:
The SERVOPACK is not in the state of the acceptance completion when the servo power is ON.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Content:
The servo board is not in the state of the acceptance completion when the servo power is ON.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the following settings.
[Released side] Reset the software limit of released side gun. (Parameter S1CxG800 or 810)
[Closed side] Reset the software limit at the gun closed side. Add the moving amount of tip wear. (Parameter S1CxG800 or 810)
Content:
In comparison to the position, where the gun tip hits the welded target, at the previous wear detection, the position during pressuring exceeded the allowable limit which had been set in “ALLOAWABLE TOUCH RANGE” in the GUN DETAIL SETTING file.
Remedy:
Check the following settings.
Description:
Sub Code: Signifies the group in which the alarm occurred
Remedy:
Check if this model is supported.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Check the teaching position.
(2) In case the alarm occurs at SVSPOT or SVSPOTMOV instruction, if you disable the gun arm bend compensation by specifying the BCOFF tag to the instruction, the alarm won’t occur.
Description:
Robot did not reach the command position within a certain time period.
Remedy:
Check the parameter setting value.
Description:
Automatic test data error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control filter error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control filter error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control filter error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control filter error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The override ratio is invalid.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The override ratio is invalid.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The override ratio is invalid.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The override ratio is invalid.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The override ratio is invalid.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The override ratio is invalid.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The override ratio is invalid.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The override ratio is invalid.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The override ratio is invalid.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Gun Auto-tuning error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The pullback was executed when the shock detection function was invalid.
Remedy:
Check the following settings.
Shock Detection Function. Pullback signal
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The data error of ROBOT DUTY DIAGNOSIS FUNCTION was detected.
(Sub Code: Signifies the data type and the axis in which the alarm occurred)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The servo OFF status was sent from the APU01 unit.
Remedy:
(1) Reset the alarm.
(2) Check the connection and inserting state of the following cables and connectors.
Content:
The pole detection in the linear encoder has not been completed.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the linear encoder.
Content:
The phase information on U-phase in the linear encoder did not agree in the encoder and the parameter.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the linear encoder.
Description:
Multiple axes are specified for hemming axis
Remedy:
Save the CMOS.BIN in maintenance mode, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Torque / Press data in the [PRESS PROOFREADING] file s not specified
Remedy:
(1) Check the [PRESS PROOFREADING] file.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Press unit in the [PRESS PROOFREADING]file is not correct
Remedy:
(1) Check the [PRESS PROOFREADING] file.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Press revision in the [PRESS PROOFREADING] file is not correct
Remedy:
(1) Check the [PRESS PROOFREADING] file.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The torque data set in the [PRESS PROOFREADING] file is not correct
Remedy:
(1) Check the [PRESS PROOFREADING] file.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The press value set in the [PRESS PROOFREADING] file is not correct
Remedy:
(1) Check the [PRESS PROOFREADING] file.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The [PRESS SETTING] file is NOT DONE.
Remedy:
(1) Check the [PRESS SETTING] file.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The press value set in the [PRESS SETTING] file is not correct
Remedy:
(1) Check the [PRESS SETTING] file.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The detect level in the [PRESS SETTING] file is not correct
Remedy:
(1) Check the [PRESS SETTING] file.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The detect delay time in the [PRESS SETTING] file is not correct
Remedy:
(1) Check the [PRESS SETTING] file.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect value has been specified for the hemming axis.
Remedy:
If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Control group of the hemming axis
Remedy:
(1) Check if the hemming axis that was picked up is correct.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the brake connection.
Description:
Sub Code: Signifies the control axis number which detected an error
Remedy:
Check the settings for CONNECTION(STO/CONTACTOR) in maintenance mode
Description:
Sub Code: Control group and axis
Remedy:
Check the following settings.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the following settings.
Description:
The arithmetic process for motion control did not complete within regulated time. No motion command was prepared.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The arithmetic processing section is not ready for JOG operation.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The arithmetic processing section is not ready for the playback operation.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The prereading processing in the arithmetic processing section has not completed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The arithmetic processing section is not ready for the timer follow-up of the conveyor tracking function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The prereading processing in the arithmetic processing section has not completed when specifying the target position.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The prereading processing in the arithmetic processing section has not completed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Unused A_BANK does not exist in the prereading processing of move instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Unused bank priority does not exist in the prereading processing of move instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
A_BANK pointer is not set.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
A_BANK conversion could not be performed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The specified A_BANK number does not exist.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when system number (MSS) was obtained.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in RMS960 system call.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Undefined interrupt command was received.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Job start condition is not defined.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in instruction prefetch queue operation.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Intermediate code is not defined.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Instruction prereading processing has not been completed normally.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in job data change.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The specified sequence number at job execution start is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The added area for interruption command is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
System number (MSS) for interruption command is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred at start of twin synchronous operation.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when SYNC specification was reset.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in occupation control group setting in MOTION section.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in path/trace control.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when waiting for a completion of main system task (job) in SYNC specification.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An attempt was made to execute an instruction that could not be executed at line sequence execution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred while obtaining the instruction information.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The instruction to be executed in the backward direction was not found.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An exceptional error occurred in job execution process.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Main processing command is incorrect in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Subprocessing command is incorrect in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Prereading processing has not been completed at job execution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
A_BANK conversion has not been completed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
System number (MSS) is incorrect in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in instruction prefetch queue operation in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred at IES switching in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
An undefined command or unused command was issued to the path control section.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check the following settings.
Description:
Sub Code: Control group
Remedy:
Register the home position for IOSPDCTRL axis.
Description:
Interpolation such as linear and circular interpolation cannot be performed with this manipulator.
Remedy:
Change the step (move instruction), where the alarm occurred, to MOVJ.
Description:
The setting of the form data for Flip/No Flip is not “B-axis Angle. "
Remedy:
Set “1” to “S2C658: Type data detail settings”.
Description:
An attempt was made to pass the B-axis zero degree position (singular area).
Remedy:
Check the teaching position of the job so that the manipulator does not pass the B-axis zero degree position (singular area).
Description:
An attempt was made to pass the B-axis zero degree position (singular area) during interpolation.
Remedy:
Check the teaching position of the job so that the manipulator does not pass the B-axis zero degree position (singular area).
Description:
Wrist axis tended to rotate to the inverse with the teaching direction.
Remedy:
Check the teaching position of the job so that a wrist axis does not inverse rotation.
Description:
Two robots are attempting to move to a position beyond the specified inter-robot distance.
Remedy:
Check the following settings.
Description:
Designation error for master and slave
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Slave designation error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Slave interpolation error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No designation of master axis
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Master-axis designation error for JOG motion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Slave-axis designation error for JOG motion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Occupation control error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Designation error of occupation control for JOG motion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Designation error of occupation control for Bank position
Remedy:
An instruction that uses reference points (WVON, COMARCON, ACORON instructions, etc.) was executed with a reference point (REFP instruction) in another control group.
(1) Check if@the instructions that use the reference points are operating with the reference points of the same control group.
(2) Register reference points before instructions that use reference points.
Description:
Designation error of occupation control group for tracking motion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No master and slave designated for tracking motion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
Among three taught points in a circular interpolation step, two or three points are on the same point.
Remedy:
Check the settings for teaching position of circular interpolation steps so that each point is different.
Content:
Among three taught points in a spline interpolation step, two or three points are on the same point.
Remedy:
Check the settings for teaching position of spline interpolation step so that each point is different.
Content:
Among three taught points to create an user coordinate system, two or three points are on the same point.
Remedy:
Check the settings for three taught points to create an user coordinate system so that each point is different.
Content:
Among three taught points (start, end, and reference points) to create a weaving coordinate system, two or three points are on the same point.
Remedy:
Check the settings for taught points (start, end, and reference points) so that each point is different.
Content:
The distance between the teaching points in the spline interpolation section is not equidistant.
Remedy:
Check the settings for the teaching position of spline interpolation section so that the distance between the teaching points is even.
Content:
In case the form (folded direction) of L- and U-axes at start point and end point are different except for MOVJ instructions, the manipulator cannot move.
Remedy:
Check the following settings.
Content:
In case the form (folded direction) of S- and L-axes at start point and end point are different except for MOVJ instructions, the manipulator cannot move.
Remedy:
Check the following settings.
Description:
Sub Code: Control group and axis
Remedy:
(1) Reduce the speed in the step where the alarm occurred.
(2) Change the move instruction to joint interpolation (MOVJ).
Description:
Sub Code: Control group and axis
Remedy:
Perform the teaching again to correct positions for manipulators so that the step where the alarm occurred is within the motion range.
Description:
Sub Code: Control group and XYZ
Remedy:
Perform the teaching again to correct positions for manipulators so that the step where the alarm occurred is within the motion range.
Description:
Sub Code: Control group and axis
Remedy:
Perform the teaching again to correct positions for manipulators so that the step where the alarm occurred is within the motion range.
Description:
Sub Code: Control group and axis
Remedy:
Perform the teaching again to correct positions for manipulators so that the step where the alarm occurred is within the motion range.
Description:
Sub Code: Control group and axis
Remedy:
Perform the teaching again to correct positions for manipulators so that the step where the alarm occurred is within the motion range.
Description:
Sub Code: Control group and axis
Remedy:
Perform the teaching again to correct positions for manipulators so that the step where the alarm occurred is within the motion range.
Description:
RT-buffer control command error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Segment-receiving control command error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No bank priority
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Answer error at MOVE simulating
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The value of bank_refresh_flag(x) exceeded its limit.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
RT-buffer tracking option error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The segment was received although the previous segment had not been sent.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control group not designated
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Slave control-group error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Master control-group error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Master and Slave control-group error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for a job file
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for a user coordinate file
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for a calibration file between manipulators
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for a tool calibration file
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for prereading-calculation start point (for adv_st_pos)
Remedy:
(1) Reset the alarm, and re-select the job from [select job] window before starting the job again .
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for the current-value preset position
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for the conveyor prereading-calculation start point
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Occupation control-group error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for servo hand
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for the prereading-calculation start point (for dm_st_pos)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for prereading-calculation start point (for dm_st_pos)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for paint gun
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for the press synchronization prereading-calculation start point
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for HPMMVON
Remedy:
(1) Reset the alarm.
(2) Review the JOB to see if it is a control group that can be executed.
Description:
Control-group error for the controller synchronization prereading-calculation start point
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for the motor gun auto teaching
Remedy:
The motor gun auto teaching function cannot be used in multiple gun control group.
Description:
Control-group error for sealing gun
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control-group error for SMOOTH
Remedy:
(1) Reset the alarm.
(2) Review the JOB to see if it is a control group that can be executed.
Description:
Control-group error for CAPTURE
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Interrupt processing error between MOTION section and system control section
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Interrupt processing error between MOTION section and SL#1
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Interrupt processing error between MOTION section and SL#2
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Interrupt processing error between MOTION section and SL#3
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Interrupt processing error between MOTION section and SL#4
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Interrupt processing error between MOTION section and SL#5
Remedy:
(1) Reset the alarm and then try again.
(2) Turn the power OFF then back ON, and try again.
Description:
Interrupt processing error between MOTION section and SL#6
Remedy:
(1) Reset the alarm and then try again.
(2) Turn the power OFF then back ON, and try again.
Description:
Interrupt processing error between MOTION section and SL#7
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Interrupt processing error between MOTION section and SL#8
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Interrupt processing error between MOTION section and CV#1
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Interrupt processing error between MOTION section and CV#2
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Interrupt processing error between MOTION section and PS#1
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Interrupt processing error between MOTION section and PS#2
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in JMS system call when an attempt was made to open a job.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No space was found in job handle value storage area when an attempt was made to open a job.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No job handle was found.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Job control proprietary is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Job control proprietary could not be changed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in exclusive control.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The intermediate code of the instruction that is to be executed is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Destination (variable) tag arrangement is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Tag data type is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Box number is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in block separation processing of intermediate code.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Box number definition is duplicated.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Undefined instruction was found at block separation of intermediate code.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
IPRM is not set.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in tag data search process.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred move instruction search process.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Variable information does not exist.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred at position file data reading.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Variable data type is not defined.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An instruction is included with incorrect intermediate code in expression instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The syntax in expression instruction is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The tag data length is zero when tag data is read.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The necessary tag data is not set.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The object to be processed was secret variable in position file control process, so it could not be processed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The object to be processed was position type variable in position file control process, so it could not be processed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Job argument settings do not match when a variable is given and/or taken between jobs.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An attempt was made to perform undefined operation at four-rule operation instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic stack used for expression operation exceeded.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Arithmetic stack used for expression operation is empty.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Operation items are lacking in expression operation and operation processing cannot be performed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The number of executing the sub-instruction with EXEC processing exceeded the maximum number.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred by the setting of the character-string type variable in the ARGF instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The intermediate code of IFEXPRESS instruction is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The syntax of IFEXPRESS instruction is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The number of components of the IFEXPRESS instruction exceeded.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The stack used for executing the IFEXPRESS instruction overflowed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The stack used for executing the IFEXPRESS instruction did underflow.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The reinterpretation of the instruction was ordered when executing the instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Tag data (box number) of the instruction that is to be executed is not supported.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
VARGF is not set.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
CAPTURE is not set.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Access mechanism for old parameters is used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An exceptional error occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The set data for byte type variable area is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The set data for integer type variable area is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The set data for double-precision integer-type variable area is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The set data for real type variable area is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The set data for character-string type variable area is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The set data for robot-axis position-type variable area is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The set data for base-axis position-type variable (S1D parameter) area is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The set data for station-axis position-type variable (S1D parameter) area is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The byte type variable is not defined.
Remedy:
Set the number of local variables to be used in the job header.
Description:
The integer type variable is not defined.
Remedy:
Set the number of local variables to be used in the job header.
Description:
The double-precision integer-type variable is not defined.
Remedy:
Set the number of local variables to be used in the job header.
Description:
The real-number type variable is not defined.
Remedy:
Set the number of local variables to be used in the job header.
Description:
The character-string type variable is not defined.
Remedy:
Set the number of local variables to be used in the job header.
Description:
The robot-axis position-type variable is not defined.
Remedy:
Set the number of local variables to be used in the job header.
Description:
The base-axis position-type variable is not defined.
Remedy:
Set the number of local variables to be used in the job header.
Description:
The station-axis position-type variable is not defined.
Remedy:
Set the number of local variables to be used in the job header.
Content:
An error occurred in circular interpolation instruction execution.
There is no continuous three points or more for circular interpolation step.
Remedy:
Perform teaching so that circulation interpolation steps are continuous three points or more.
Content:
An error occurred in spline interpolation instruction execution.
There is no continuous three points or more for spline interpolation step.
Remedy:
Perform teaching so that spline interpolation steps are continuous three points or more.
Content:
The job to be executed is not registered.
Remedy:
Check if the CALL/JUMP destination job is registered. If the job is not registered, delete the JUMP instruction where an alarm occurred.
Content:
An error occurred in label jump execution.
The label for jump destination does not exist in the job.
Remedy:
Check if the JUMP destination label is registered. If the label is not registered, delete the JUMP instruction where alarm occurred.
Content:
Call source job does not exist in the job call stack.
Remedy:
Check the following settings.
Content:
An error occurred when memory area for local variable was obtained.
Memory area is lacking because too many local variables in the job are used.
Remedy:
Reduce the number of local variables to be used.
Description:
Sub Code:
The lowest eight bits -> Bit specification of axis where error occurred.
The highest eight bits -> Bit specification of control group number(0-31) where error occurred.
Remedy:
Move the manipulator by the axis operation, etc. to remove the external force of axis where alarm occurred.
Description:
The token for prereading processing could not be obtained.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The prereading processing has not been completed within the time, and the waiting time for completion exceeded the limit.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The prereading operation processing has not been completed within the time, and the waiting time for completion exceeded the limit.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in prereading operation process.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
A_BANK conversion has not been completed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, turn the main power of controller off and then turn it on. Re-select the job from [select job]window before starting the job again .
(3) If the alarm occurs again even though you do above (2) , save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An exceptional error occurred in job execution process.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The variable value exceeded the limit.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the binary (0/1) data type variable exceeded the limit.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the signed 1-byte data type variable is less than the minimum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the unsigned 1-byte data type variable is less than the minimum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the signed 2-byte data type variable is less than the minimum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the unsigned 2-byte data type variable is less than the minimum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the signed 4-byte data type variable is less than the minimum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the unsigned 4-byte data type variable is less than the minimum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the real-number 4-byte data type variable is less than the minimum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the character-string type variable is less than the minimum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the signed 1-byte data type variable exceeded the maximum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the unsigned 1-byte data type variable exceeded the maximum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the signed 2-byte data type variable exceeded the maximum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the unsigned 2-byte data type variable exceeded the maximum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the signed 4-byte data type variable exceeded the maximum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the unsigned 4-byte data type variable exceeded the maximum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the real-number 4-byte data type variable exceeded the maximum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
The value for the character-string type variable exceeded the maximum value.
Remedy:
Check the settings for variable, and then correct the job to fall within the input range of the tag.
Description:
Starting point and destination point are the same position.
Remedy:
Change the teaching points so that circular interpolation points do not to same.
Description:
Any points of the circular interpolation are the same position.
Remedy:
Change the teaching points so that circular interpolation points do not to same.
Description:
Any points of the circular interpolation are the same position as the center position.
Remedy:
Change the teaching points so that circular interpolation points do not to same as the center point of circular path.
Description:
The three points taught for the circular interpolation points line in a straight line.
Remedy:
Change the teaching points so that circular interpolation points do not line in a straight line.
Description:
The starting point and destination point taught for the circular interpolation points line in a straight line.
Remedy:
Change the teaching points so that circular interpolation points do not line in a straight line.
Description:
Rotation angle of circular interpolation is out of range.
Remedy:
Change the rotation angle of circular interpolation.
Description:
Failed to calculate the circular path.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Circular interpolation different ways in multiple robots are specified.
Remedy:
Specify the same circular interpolation method to all robots.
Description:
Weaving control-group designation error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
When the speed is specified by weaving time in the weaving file, zero or the negative value is set for the weaving time.
Remedy:
Reset the value 0.1 seconds or more.
Description:
When the speed is specified by frequency in the weaving file, zero or the negative value is set for the frequency.
Remedy:
Reset the value 0.1 Hz or more.
Description:
When the timer mode is specified in the weaving file, a negative value is set for the timer value.
Remedy:
Set a positive value for the timer value.
Description:
For triangle or L-type weaving, zero is set for the vertical or horizontal distance.
Remedy:
Set a positive value for the vertical and horizontal distance.
Description:
The coordinate control axis designation for the reference point is different from actual control axis.
Remedy:
Match the control group designation of the wall point and weaving execution.
Description:
The distance between the point P and the TCP could not be calculated in wrist weaving.
Remedy:
Set the correct dimensions in the tool data.
Description:
The distance between the point P and the TCP could not be calculated in circular wrist weaving.
Remedy:
Set the correct dimensions in the tool data.
Description:
The Y-direction element of circular coordinate system for circular wrist weaving could not be calculated.
Remedy:
Check the settings for wall and horizontal direction.
Description:
The X-direction element of circular coordinate system for circular wrist weaving could not be calculated.
Remedy:
Check the settings for wall and horizontal direction.
Description:
Weaving basic-orientation calculation error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Calculation error of horizontal- and wall-direction vector for weaving
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Weaving synchronization file number selection range error
Remedy:
Check the number of the weaving synchronizing file for use.
Description:
Weaving interpolation error
Remedy:
The ELLIPSE weaving can move, when MOVL or MOVC is taught.
Check the job contents.
Description:
Weaving coordinated motion error
Remedy:
The independent motion and coordinated motion are taught in the weaving section. In one weaving section teach the independent motion or coordinated motion only.
Check the job contents.
Description:
WVON instruction execution error while changing weaving conditions
Remedy:
Do not execute the WVON instruction while changing the weaving condition by the WVCHG instruction.
Check the job contents.
Description:
Weaving condition change mode error
Remedy:
The WVCHG instruction cannot be used in weaving mode other than the “ELLIPSE” or “ELLIPSE (TOOL)”.
Check the job contents.
Description:
Weaving condition change speed specification error
Remedy:
If the speed specification of the weaving condition is “time”, the condition cannot be changed by the WVCHG.
Check the weaving condition.
Description:
Weaving condition change groove correction execution error
Remedy:
The weaving groove correction function (WVADJ) and WVCHG cannot be used together.
Check the job contents.
Description:
Weaving condition change COMARC execution error
Remedy:
The COMARC function and the WVCHG cannot be used together.
Check the job contents.
Description:
SLOPE control execution error when changing weaving conditions
Remedy:
The slope control of the weaving condition and the WVCHG cannot be used together.
Check the job contents or the weaving condition.
Content:
The position type variable data type is different.
Remedy:
Match the data type of position type variable.
Description:
An error occurred in tool file number check.
Remedy:
Confirm that the specified tool file number is 0 to 63.
Description:
An error occurred in user coordinate file number check.
Remedy:
Confirm that the specified user coordinate file number is 1 to 63.
Description:
An error occurred in calibration file number check between the manipulators.
Remedy:
Confirm that the specified robot calibration file number is 1 to 32.
Description:
An error occurred in tool calibration file number check.
Remedy:
Confirm that the specified tool file number is 0 to 63.
Description:
An error occurred in reference point number check.
Remedy:
Confirm that the specified robot calibration file number is 1 to 8.
Description:
An error occurred in check for welding start condition file number.
Remedy:
Confirm that the specified welding condition start file number is 1 to 48.
Description:
An error occurred in check for welding end condition file number.
Remedy:
Confirm that the specified welding condition end file number is 1 to 48.
Description:
An error occurred in conveyor characteristic file number check.
Remedy:
Confirm that the specified conveyor condition file number is 1 to 6.
Description:
An error occurred in press characteristic file number check.
Remedy:
Confirm that the specified press characteristic file number is 0 to 3.
Description:
An error occurred in conveyor calibration file number check.
Remedy:
Confirm that the specified conveyor calibration file number is 1 to 6.
Description:
An error occurred in argument number check.
Remedy:
Confirm that the argument number is 1 to 16.
Description:
An error occurred in check for motor gun characteristic file number.
Remedy:
Confirm that the specified servo gun characteristic file number is 1 to 24.
Description:
An error occurred in servofloat condition files check.
Remedy:
The servofloat condition file is “UNUSED”. Specify the servofloat condition file of either “FL#()” or “LFL#()” in detail edit display.
Description:
An error occurred in press condition file number check.
Remedy:
Confirm that the specified press condition file number is 1 to 3.
Description:
An error occurred in press setting file number check.
Remedy:
Confirm that the specified press setting file number is 1 to 128.
Description:
Sub Code: Reference point number in binary
Remedy:
Set the reference point.
Content:
The job call stack exceeded the limit.
An attempt was made to add more than twelve stacks in the job call stack.
Remedy:
Change the job configuration so that the number of nests for CALL instruction is twelve or less.
Description:
The variable number is out of range.
Sub Code: The variable number which an attempt was made to use
Remedy:
Correct the job using the variable number within the range.
Content:
The arc welding characteristic file is not set.
Remedy:
Complete the settings for the arc welding characteristic file.
Content:
The welding start condition file is not set.
Remedy:
Complete the settings for the welding start condition file.
Content:
The welding end condition file is not set.
Remedy:
Complete the settings for the welding end condition file.
Content:
An error occurred in welder type check.
The reference unit for the welding voltage and the welder type (independent/unified) do not match.
Remedy:
Check the settings for the reference unit of the welding voltage.
Content:
An error occurred in expression operation.
The operation is impossible because the expression is too long.
Remedy:
Separate the operation expression, shorten the expression, and then check the settings for the job.
Content:
An error occurred in operation instruction.
Zero division occurred.
Remedy:
Do not divide by zero.
Content:
An error occurred in automatic welding release conditions.
The number of welding release condition is zero for arc auxiliary file.
Remedy:
Check the settings for the number of times of welding release condition.
Description:
The arc retry has been set, but no move instruction exists following ARCON instruction.
Remedy:
Check the settings for the move instruction following ARCON instruction.
Description:
The teaching position before and after the ARCON instruction is the same position.
Remedy:
Check the following settings.
-Check the settings for the move instruction following ARCON instruction.
-Change “Retry mode” from “SHIFT” to “RERPLY”.
Description:
Master control-group doesn’t support Retry mode “SHIFT”.
Remedy:
Change “Retry mode” from “SHIFT” to “RERPLY”.
Content:
The parity check for user I/O group detected the data error.
Remedy:
Check the settings for the parity data of the user I/O group.
Content:
The BCD value exceeded the limit.
An attempt was made to output a value above the maximum value that can be expressed in Binary Coded Decimal: 99 (decimal) when no parity check is specified, and 79 (decimal) when parity check is specified.
An attempt was made to read a data that cannot be expressed in Binary Coded Decimal (a data whose lower or upper 4 bits exceeded 9 in decimal) in the variable.
Remedy:
Correct the BCD data so that it is within the limit.
Content:
The binary data exceeded the limit.
An attempt was made to output a value that exceeded 127 (decimal) to the user I/O when parity check was specified.
Remedy:
Correct the binary data so that it is within the limit.
Description:
An undefined command was issued to the offline position-data preparation section.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
An error occurred at user coordinate creation by a job.
The number of steps was lacking for a job for user coordinate creation.
Remedy:
Correct the JOB that the number of steps will be three or more.
Description:
The calibration between manipulators cannot be executed for this model.
Remedy:
Do not use a coordinated motion with this manipulator.
Description:
The master group and the slave group are set to the same group.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect designation of the control group for master group
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect designation of the control group for slave group
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect designation of the occupation control group for calibration data
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect designation of the enabling control group for calibration data
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Among three points in the master-group’s calibration data, two or three points are on the same point.
Remedy:
Teach the data for calibration so that each point is different.
Description:
Among three points in the slave-group’s calibration data, two or three points are on the same point.
Remedy:
Teach the data for calibration so that each point is different.
Description:
The number of the teaching points for calibration data is insufficient.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The calibration between manipulators cannot be executed for this model.
Remedy:
The calibration function between manipulators cannot be used for this model.
Description:
The master group and the slave group are set to the same group.
Remedy:
Set the different groups for the master group and the slave group.
Description:
Incorrect designation of the control group for master group
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect designation of the control group for slave group
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Calibration data setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
An error occurred at calibration data creation between manipulators.
The number of steps was lacking for a job for calibration data creation between manipulators.
Remedy:
Check the settings for number of the job steps
Description:
Incorrect number of teaching points for tool calibration
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect designation of the occupation control group for calibration data
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect designation of the enabling control group for calibration data
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect designation of the control group for calibration data
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The reference point is not set.
Remedy:
Set the reference point.
Description:
The start point and end point are on the same point.
Remedy:
Change the teaching positions so that the start point and end point are different.
Description:
The straight line which connects the start point and an end point, and the angle which the Z direction of a tool makes are less than 10 degrees.
Remedy:
Correct the teaching positions so that the angle that the Z direction of the tool and the straight line which connects the start point with the end point make becomes 10 degrees or more.
Content:
The alarm occurred in the calculation section could not be reset.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code:The related control-group
Remedy:
Check the following settings.
Content:
The robot axis is not designated for the control-group of the job at execution of a work instruction that uses a manipulator.
Remedy:
Check the following settings.
Description:
An attempt was made to change the tag data.
Remedy:
Release the prohibition.
Description:
An attempt was made to change the speed tag data.
Remedy:
Release the prohibition.
Description:
An attempt was made to change the board thickness tag data.
Remedy:
Release the prohibition.
Description:
An attempt was made to change the MARKER job.
Remedy:
Release the prohibition.
Description:
Sub Code: Application number
Remedy:
Check the following settings.
Content:
MotoPlus application doesn’t response more than stipulated time because MM task has not recovered from unexpected condition.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ACP01 board. save the CMOS.BIN before replacing the board to be safe. After replacement, insert the SD card that has been used for the old ACP01 board to the new one.
(3) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
MM Task cannot run more than stipulated time because of MotoPlus application running. Executing high priority task of MotoPlus application may dominate CPU for a long time, which may be preventing the man machine interface task from running.
Remedy:
Check if there is high priority task of MotoPlus application running long time. Especially, check if there may be the process which waits for a special condition without executing mpTaskDelay in loop process. If such process exists, suitable remedy should be done like putting mpTaskDelay in the loop process.
Description:
Sub Code:Sensor number
Remedy:
Select the option function for the specified robot in the option function selection of maintenance mode.
Description:
Attributes are changed during trajectory adjustment. Cannot be changed during trajectory adjustment of these attributes.
Remedy:
Please change after end of trajectory adjustment.
Description:
The coordinate number is out of range.
Remedy:
Input correct data.
Description:
The tool number is out of range.
Remedy:
Input correct data.
Description:
The unit is out of range.
Remedy:
Input correct data.
Description:
The coordinate system is unsupported.
Remedy:
Input correct data.
Cause:
Software operation error occurred
Remedy:
(1) Reset the alarm and execute again.
(2) )If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Software operation error occurred
Remedy:
(1) Reset the alarm and execute again.
(2) )If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Software operation error occurred
Remedy:
(1) Reset the alarm and execute again.
(2) )If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Software operation error occurred
Remedy:
(1) Reset the alarm and execute again.
(2) )If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Software operation error occurred
Remedy:
(1) Reset the alarm and execute again.
(2) )If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Software operation error occurred
Remedy:
(1) Reset the alarm and execute again.
(2) )If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Software operation error occurred
Remedy:
(1) Reset the alarm and execute again.
(2) )If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Application number
Remedy:
Check the following settings.
Content:
When executing a sensor instruction, the robot specified to use the sensor (system parameter) and the robot specified to use the application (system parameter) are unmatched.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
When executing COM-ARC function, the path was beyond the specified path-over monitor zone.
Remedy:
Set the path over radius within the allowable range.
Description:
R1
Remedy:
Set the path over radius within the allowable range.
Description:
R2
Remedy:
Set the path over radius within the allowable range.
Description:
R3
Remedy:
Set the path over radius within the allowable range.
Description:
R4
Remedy:
Set the path over radius within the allowable range.
Description:
R5
Remedy:
Set the path over radius within the allowable range.
Description:
R6
Remedy:
Set the path over radius within the allowable range.
Description:
R7
Remedy:
Set the path over radius within the allowable range.
Description:
R8
Remedy:
Set the path over radius within the allowable range.
Content:
An error occurred in mechanical parameter for the path control section.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The C- and W-axis position at the cutting start position is not zero pulse.
Remedy:
Check the settings for the cutting start position (zero pulse).
Description:
Zero is set for the cutting radius.
Remedy:
Check the settings for radius (a value bigger than zero).
Description:
The cutting machine axis is not mounted.
Remedy:
The CUT instruction can be used for the manipulator with small-circle cutting axis only.
Description:
This manipulator cannot perform a hexagonal cutting motion.
Remedy:
Select an other cutting form.
Description:
After the Endless rotation completed, an attempt was made to execute an interpolation instruction such as MOVL and MOVC before executing an MRESET instruction.
Remedy:
To perform an interpolation motion such as MOVL and MOVC after an Endless rotation, execute an MRESET instruction beforehand.
Description:
The base axis is set as an Endless rotation axis. The Endless function cannot be used with the base axis.
Remedy:
Check the parameter setting that designates the Endless rotation axis.
Description:
An attempt was made to execute the Endless function although the endless axis was not designated.
Remedy:
Check the parameter setting that designates the Endless rotation axis.
Description:
The Endless axis exceeded the maximum pulse value (plus or minus536870911).
Remedy:
Set the rotation amount so that the Endless axis does not exceed the maximum pulse value.
Description:
Control-group designation error for correcting-direction preparation
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Designation error for the correcting-direction coordinates
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
When “any direction” is set for the correcting direction, the correction coordinates is not prepared.
Remedy:
Check the settings for the correcting direction with the reference point (REFP).
Description:
When “any direction” is set for the correcting direction, the reference points (REFP) are taught on the same point.
Remedy:
Check the settings for the reference points (REFP) so that each point is different.
Description:
Designation error for the coordinated motion control axis at the reference point
Remedy:
Match the control group designation of the wall point and weaving execution.
Description:
Data unmatched between the correction amount data and the job data:
The information about the control groups designated for the series of jobs, which is added to the correction amount data, does not include the valid control-group for the job.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Data unmatched between the correction amount data and the job data:
The valid control-group information that is added to the correction amount data disagrees with the valid control-group for the job.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Tool change err for orientation correction of the tool coordinate
Remedy:
It is not possible to change the tool when correct the orientation by the tool coordinate.
Content:
The tool file number exceeded the limit value.
The tool number for internal control is 65 or more.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The weaving start point and end point are on the same point.
Remedy:
Check the settings for the positions so that the weaving start point and end point are different.
Description:
Among the weaving start point, end point, and reference point, two or three points are on the same point.
Remedy:
Check the settings for the positions so that the weaving start point, end point, and reference point are different.
Description:
Sub Code: Control group which calibration is not completed
Remedy:
Before using the coordinated motion, execute the calibration between manipulators.
Description:
The setting of the manipulator number is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero is set for the resolution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero is set in the feedback pulse parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting of L-axis ball-screw data is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting of U-axis ball-screw data is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or a negative value is set for MAXPPS.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or a negative value is set for the maximum acceleration speed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or a negative value is set for the maximum deceleration speed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or a negative value is set for the play-mode servo averaging time.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting of the manipulator number is incorrect. An undefined type is designated.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The incorrect coordinate system is designated for the cubic interference. An undefined coordinate system is set.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The designation of the user coordinates number is incorrect. A number out of the setting range is set.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The reduction ratio <= 0 is output.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or a negative value is set for the spring constant.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or a negative value is set for the motor inertia.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or a negative value is set for the speed calculation constant.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Dividing number setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting of allowable torque for the speed reducer is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting of allowable torque for the motor is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The manipulator type is not applicable for torque acceleration/deceleration.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or a negative value is set for the balancer.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The angle of hexagon set for the CUT instruction is out of the range “0 degree < angle < 60 degrees.”
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Encoder type designation error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Observer sampling time error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Two-degree-of-freedom system Kp value error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting of torque acceleration/deceleration designation parameter is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Observer polarity setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The inertia value error for the shift value calculation
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Observer attenuation constant error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Torque estimation parameter error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The segment clock error occurred when the PV loop is 1 ms.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Non-robot axis observer selection error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero is set for the response time constant.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Efficiency data error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero is set for the averaging time constant.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Torque limit ratio data error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Coulomb friction data error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Kinematic friction coefficient data error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting in the optimized acceleration/deceleration designation parameter is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An uninstalled function is designated.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The dynamics-model calculation at the optimized acceleration/deceleration is invalid.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero is set for the inertia of dynamics fixed model.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Designation error for dynamics-model calculation type
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The optimized acceleration/deceleration control of speed limit function is disabled.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The axis designation parameter for the speed limit function is not set.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting in the mode designation parameter for the speed limit function is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or negative value is set in the allowable braking torque parameter for the speed limit function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or a negative value is set in the speed adjustment ratio parameter for the speed limit function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or a negative value is set in the torque limit adjustment ratio parameter for the acceleration/deceleration tuning.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or a negative value is set in the parameter that sets the shortest acceleration/deceleration time for when the excessive torque is applied at the optimized acceleration/deceleration.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero is set for the dimension information “a3” for the SKR manipulator.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting of sealer-gun control-group parameter for the servo sealer control is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The parameter setting for the Cartesian manipulator X-axis data is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The parameter setting for the Cartesian manipulator Y-axis data is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting for the Dual-arm manipulator is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or a negative value is set in the FORMCUT maximum acceleration/deceleration time parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting of expanded check-point designating bits for the arm interference check is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or a negative value is set for the sphere at the arm interference check point.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero or a negative value is set for the cylinder at the arm interference check point.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The number of designated check points for the arm interference check is insufficient.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
All of X, Y, and Z value of the expanded check-point 1 for the arm interference check are set to zero.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
All of X, Y, and Z value of the expanded check-point 2 for the arm interference check are set to zero.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting of wrist axis angle for tube-incorporated wrist type manipulators or three-roll wrist type manipulators is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The special link JOG operation cannot be used with this manipulator.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting in the parameter for special angle limit check designation is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting of the deceleration speed for the path-priority control is less than zero.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
A negative value is set in the roundness parameter for the path-priority control.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The link parameter for the cutting device is not set.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The real-time bending correction function is enabled for a control-group other than robot axis.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero is set for the dimension information “a2” for the Arc Cell Torch Arm type manipulators.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Zero is set for the deceleration ratio for double T-axis unit of the V-shaped double T-axis manipulator.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
“alpha” is replaced with “0” in SKR1-5 type robot.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Wrong value in set for backlash correction function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect parameter setting to inertia speed control function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect acceleration/deceleration time setting at tool mass acceleration/deceleration speed correction function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect coefficient/item settings at tool mass acceleration/deceleration speed correction function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No tool mas as the minimum acceleration/deceleration time at tool mass acceleration/deceleration speed correction function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect speed setting at tool mass acceleration/deceleration speed correction function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect coefficient/item settings at tool mass acceleration/deceleration speed control function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No tool mass as the maximum acceleration/deceleration time at tool mass acceleration/deceleration speed control function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error in the standard arithmetical axis number setting for approximation model.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error in the standard expanding point number setting for approximation model.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error in the radius setting for approximation model.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
setting error of arithmetical axis number in D-H method.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
setting error of choosing no / wrong connection base arithmetical axis number in D-H method.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The higher-order acceleration/deceleration is prohibited when using operation acceleration / deceleration
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Base axis control point to Robot coordinate system offset setting prohibited
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Pulse linked JOG function specification error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Dual drive control specification error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Notch filter supported acceleration and deceleration tuning: Notch filter function setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Notch filter supported acceleration and deceleration tuning: Notch filter (z2) setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Other
Remedy:
If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Other
Remedy:
If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Other
Remedy:
If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Other
Remedy:
If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Other
Remedy:
If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Other
Remedy:
If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Other
Remedy:
If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
NON ACTIVATION of Servo Simulation function error
Remedy:
Enable Servo Simulation Function.
Cause:
Other
Remedy:
If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting error of vibration suppression filter for SVSPOTMOV
Remedy:
Confirm that the threshold value for the vibration suppression filter should be larger than the one in previous table.
Description:
the setting error of time constant for the vibration suppression filter for SVSPOTMOV
Remedy:
Confirm that the time constant for vibration suppression filter for SVSPOTMOV must be the different value of Kp.
Cause:
Other
Remedy:
If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
the setting error of the number for vibration suppression filter for SVSPOTMOV
Remedy:
Confirm that the number of the tables activated for vibration filter is less than 5.
Cause:
Other
Remedy:
If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting in the parameter for special mechanical interference is incorrect.
Remedy:
Correct the setting value of the parameter for special mechanical interference.
Description:
Endless function
encoder err
Remedy:
Save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect parameter setting at tool mass acceleration/deceleration speed control function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect parameter setting at tool mass acceleration/deceleration speed limit function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect parameter setting at gun speed limit function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Timing delay control function was invalid
Remedy:
Enable timing delay control function.
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect parameter setting at TCP speed acceleration/deceleration speed limit function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect parameter setting at short pitch interval SPF frequency change function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect parameter setting at press full synchronous shift amount press speed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect parameter setting at speed corresponding position correction amount condition.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect parameter setting at inertia SPF frequency change function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Cause:
Setting error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect parameter setting at short pitch interval SNAP minimum acceleration/deceleration time change function.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Some of the teaching points for master-group are on the same point.
Remedy:
Perform the teaching again so that the teaching points are different from one another.
Description:
Some of the teaching points for slave-group are on the same point.
Remedy:
Perform the teaching again so that the teaching points are different from one another.
Description:
The 2nd-axis positions of C3, C4, and C5 of station axes are not the same.
Remedy:
Perform the teaching again so that the 2ndaxis positions of C3, C4, and C5 of the station axes are the same.
Description:
The 1st-axis positions of C1, C2, and C3 of station axes are not the same.
Remedy:
Perform the teaching again so that the 1staxis positions of C1, C2, and C3 of station axes are the same.
Description:
The 2nd-axis positions of C1, C2, and C3 of station axes are the same.
Remedy:
Perform the teaching again so that the teaching positions are different from one another.
Description:
The 1st-axis rotation direction of C3, C4, and C5 of station axes are not the same.
Remedy:
Perform the teaching again so that the 1staxis rotation direction of C3, C4, and C5 of station axes are the same.
Description:
The 1st-axis (elevation axis) positions of C1, C2, and C3 of station axes are not the same.
Remedy:
Perform the teaching again so that the 1staxis (elevation axis) positions of C1, C2, and C3 of station axes are the same.
Description:
The 1st-axis (elevation axis) positions of C3, C4, and C5 of station axes are not the same.
Remedy:
Perform the teaching again so that the 1staxis (elevation axis) positions of C3, C4, and C5 of station axes are the same.
Description:
An attempt was made to execute an instruction that could not be executed in a job without control group.
Remedy:
Check the settings for the job instruction with control group.
Description:
Sub Code: The variable number
Remedy:
Check the settings for the position type variable.
Description:
Sub Code: User coordinate number
Remedy:
Check the settings for the user coordinate.
Description:
Sub Code: Task number
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The option board was detected not to operate normally at power ON.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
Arc retry could not be executed because there was no step before the ARCON instruction.
Remedy:
Register a step before the ARCON instruction.
Content:
Arc-restart-return could not be executed because there was no restart-return step in the job. (Example: A retry request was made while executing a step of the called job.)
Remedy:
Check the settings for the job.
Content:
Incorrect teaching point for search detection.
The search start point and the motion target point are the same, or the distance between the two points is too short.
Remedy:
Check the following settings.
Description:
The specified coordinate system does not exist.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the master tool coordinate system. This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the tool coordinate system. This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the direction of travel coordinate system (for a shared function). This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the any direction coordinate system (for a shared function). This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the approximation tool coordinate system (for a shared function). This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the conveyor coordinate system. This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the COMARC coordinate system. This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the power sensor coordinate system. This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the cylindrical coordinate system. This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the coordinate system for the external reference point. This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the coordinate system for 3D shifting. This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the KOMATSU tool Z-direction operation coordinate system. This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the KOMATSU tool JOG operation coordinate system. This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the coordinate system at IMOV for 3D shifting. This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the H-LINK type cylindrical coordinate system. This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the FSER_FRAME type cylindrical coordinate system. This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
Designation error of the reference USER_FRAME type cylindrical coordinate system. This coordinate system cannot be used.
Remedy:
Check the settings for the coordinate system which can be used.
Description:
The master-tool user coordinates could not be prepared.
Remedy:
Execute the MFRAME instruction in coordinated job when you make the master tool user coordinate.
Description:
reference user frame cannot be used.
Remedy:
Check the following settings.
Description:
position type variable (P variable) cannot be used.
Remedy:
Check the following settings.
Content:
The SQRT instruction could not be executed.
An attempt was made to calculate the square root of negative value. (The second argument was negative.)
Remedy:
Check the job settings so that the second argument of SQRT instruction does not become negative.
Description:
Sub Code: Control group exceeding the allowable value
Remedy:
Confirm the load setting to the robot.
Content:
In the user coordinates for calibration between manipulators, three or more teaching points are aligned in a straight line.
Remedy:
Check the settings so that the teaching points are not aligned in a straight line.
Description:
Sub Code: Control group and axis
Remedy:
Check the following settings.
Description:
Sub Code: Control group and axis
Remedy:
Check the following settings.
Description:
Sub Code: The related control-group
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: The related control-group
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Control group
Remedy:
Check the settings for the general-purpose input signal set in the parameter.
Description:
Sub Code
0000_0001: A robot job was started from the concurrent job at CALL/JUMP instruction execution.
0000_1001: A concurrent job was started from the robot job at CALL/JUMP instruction execution.
1000_0001: A system job was started from the robot job at CALL/JUMP instruction execution.
Remedy:
Check the settings for the job to be started.
Description:
An attempt was made to change the contents of variable tag data.
Remedy:
The variable tag cannot be changed. Correct the job so as not to use the variable tag.
Description:
An attempt was made to change the tag data for the job prohibited from being edited.
Remedy:
Release the prohibition.
Description:
An error occurred at instruction read-in.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The tag is not registered.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The tag data was variable specification.
Remedy:
The variable tag cannot be changed. Correct the job so as not to use the variable tag.
Description:
The value which it was made to change exceeded the limit of tag data.
Remedy:
Check the contents of changing data.
Description:
An error occurred at tag data change.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The teaching points are incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Robot information for implementing the shared base axes control can not be acquired.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Robot axes, base axis specification error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control number of the main side base axis is abnormal.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Independent control base axis group error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Shared base axes current value creation error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Independent control slave side speed calculation error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Independent control slave side speed check error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Independent control Prohibit command execution error.
Remedy:
In shared base axes control, the robot of slave side MOVS, EIMOVL, EIMOVC can not be used. Please correct the job.
Description:
Independent control slave side coordinated motion specification error.
Remedy:
The independent control slave side, can not be coordinated motion. Please correct the job.
Content:
An error occurred at concurrent job execution.
There was an instruction that cannot be executed such as move instruction in the concurrent job.
Remedy:
Delete an instruction that cannot be executed such as move instruction in the concurrent job.
Description:
An interrupt job (user setting) is started up during the back operation.
Remedy:
Check the job so that the interrupt job will not start-up during the back operation.
Description:
An suspend macro job is started up during the back operation.
Remedy:
Check the job so that the suspend macro job will not start-up during the back operation.
Description:
An interrupt job (inside the system) is started up during the back operation.
Remedy:
Check the job so that the interrupt job will not start-up during the back operation.
Description:
A FOLGE job is started up from a job except the registered master job.
Remedy:
Check the job so that the FOLGE job will start-up from the registered master job.
Content:
Incorrect analog output port number.
The specified analog output port number was not allowed.
Remedy:
Check the settings for the specified analog output port number.
Description:
A syntax error was found in the IF sentence.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
A job without control group was started by SYNC instruction.
Remedy:
Check the control group setting of the job to be started by SYNC.
Description:
A job only with robot axes was started by SYNC instruction.
Remedy:
Check the control group setting of the job to be started by SYNC.
Description:
A job only with master control group axes was started by SYNC instruction.
Remedy:
Check the control group setting of the job to be started by SYNC.
Description:
At full synchronization, the completion timings of move instructions for the master and the slave disagreed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
At full synchronization, no operation request from the master was sent.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
At full synchronization, the execution timings of move instructions for the master and the slave disagreed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The twin synchronous ID number is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An attempt was made to execute triple synchronization when specified Sub-master for the master was different.
Remedy:
Match the system number specification of the master between the job to be started by SYNC.
Description:
Combination of twin coordination, SYNC instruction and TRACK instruction are mixed.
Remedy:
Please unify the combination of twin coordination with SYNC instructionor TRACK instruction.
Description:
The base axis specification is other than 1 or 2 for conveyor characteristic file.
Remedy:
Set the base axis specification of conveyor characteristic file to either 0, 1, or 2.
Description:
No robot axis in the job for robot axis tracking
Remedy:
Correct the job setting so that the robot axis tracking is executed in the job where robot axis exists.
Description:
No base axis in the job for base axis tracking
Remedy:
Correct the job settings so that the base axis tracking is executed in the job where base axis exists.
Description:
The conveyor board number and conveyor characteristic file number used are incorrect.
Remedy:
Check the specification of conveyor condition file number for use.
Description:
There was no conveyor start position data at prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No base axis in the job for arc tracking
Remedy:
Correct the job setting so that the arc tracking is executed in the job where robot axis exists.
Description:
The set value for the TRACKING CORRECTION in a Conveyor condition file is abnormal.
Remedy:
Set a larger value for the TRACKING CORRECTION in the Conveyor condition file to be used.
Description:
Sub Code: Conveyor characteristic file number
Remedy:
Set “Use state” of conveyor characteristic file to “1: Use.”
Description:
Sub Code: Conveyor number
Remedy:
Correct the “Conveyor Lowest Speed” set in the conveyor characteristic file.
Description:
Designation error of the conveyor tracking control-group
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Designation error of the user coordinates for the conveyor tracking
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An attempt was made to use the conveyor tracking function with the slave manipulator at coordinate motion.
Remedy:
The conveyor tracking cannot be executed to the slave manipulator of the coordinate system. Correct the job so that the conveyor tracking perform by the robot unit or without coordinated motion.
Description:
Zero is set for the resolution for the turn-table synchronization.
Remedy:
Check the settings for the resolution.
Content:
The load torque of an axis motor exceeded the allowable value when the manipulator is operating at the specified speed.
Remedy:
Check the following settings.
Description:
An attempt was made to obtain the byte type system variable by the other type variable.
Remedy:
Obtain as the byte type variable.
Description:
An attempt was made to obtain the integer type system variable by the other type variable.
Remedy:
Obtain as the integer type variable.
Description:
An attempt was made to obtain the double-precision integer-type system variable by the other type variable.
Remedy:
Obtain as the double-precision integer-type variable.
Description:
An attempt was made to obtain the real-number type system variable by the other type variable.
Remedy:
Obtain as the real-number type variable.
Description:
An attempt was made to obtain the character-string type system variable by the other type variable.
Remedy:
Obtain as the character-string type variable.
Description:
“SYMOVJ” instruction is executed at robot-axis tracking.
Remedy:
Do not use “SYMOVJ” instruction in robot axis tracking.
Description:
The Corner-R motion cannot be used for coordinated motion.
Remedy:
Do not use the Corner-R motion for coordinated motion.
Description:
An attempt was made to execute the Corner-R motion for the same point.
Remedy:
Check the settings for the teaching so that the start step and end step are not on the same point.
Description:
The Corner-R zone is taught on a straight line.
Remedy:
Check the settings for teaching so that the Corner-R zone is not on a strait line.
Description:
The start position or end position for the Corner-R motion could not be calculated inside the start zone or the end zone.
Remedy:
Check the following settings.
Description:
The Corner-R motion cannot be used for coordinated motion (with master manipulators).
Remedy:
Do not use the Corner-R motion for master manipulators at coordinated motion.
Description:
The Corner-R motion cannot be used for MOVC, MOVS, and EIMOVC instructions.
Remedy:
Use a MOVL instruction when using the Corner-R motion.
Description:
The Corner-R motion is disabled during weaving.
Remedy:
Do not perform weaving when using the Corner-R motion.
Description:
Different tool numbers are set in a Corner-R zone (for the Corner-R middle step and end step).
Remedy:
Use the same tool number in a Corner-R zone.
Description:
The Corner-R motion is disabled when the higher-order acceleration/deceleration is specified.
Remedy:
Disable the higher-order acceleration/deceleration when using the Corner-R motion.
Description:
The Corner-R motion is disabled during conveyor tracking.
Remedy:
Do not perform the conveyor tracking when using the Corner-R motion.
Description:
Arithmetic error occurred when calculating the acceleration and deceleration time for the Corner-R operation
Remedy:
Do not perform the conveyor tracking when using the Corner-R motion.
Description:
Arithmetic error occurred when calculating acceleration and deceleration during test run in consideration of servo delay for the Corner-R motion.
Remedy:
Do not perform the conveyor tracking when using the Corner-R motion.
Content:
No job queue data.
“QUE” is used in CALL or JUMP instruction under the condition that no job queue is used.
Remedy:
Use “CALL QUE” under the condition that the job data is set to the job queue .
Description:
There was no character string representing a constant in character string to be extracted at VAL instruction execution.
Remedy:
Check the settings for the data of the character string to be extracted.
Description:
An MRESET instruction was executed while no endless axis was designated.
Remedy:
Set the endless axis.
Description:
At job return, an attempt was made to fetch a data from an empty job call stack or to stack a data in the job call stack that is full.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The first character of character string to be extracted is null at MID$ instruction execution.
Remedy:
Check the settings for the data of the character string to be extracted.
Description:
The extraction start position exceeds the character string length at MID$ instruction execution.
Remedy:
Check the settings for the data of the character string to be extracted.
Description:
The trajectory calculation couldn’t be performed since the V/T is set to less than 4.
Remedy:
Review tag setting of the FOLLOW2 instruction.
Description:
The trajectory calculation couldn’t be performed since total stroke volume is less than caught volume.
Remedy:
Review the DD= tag of the FOLLOW2 instruction.
Description:
Sub Code: System number
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Error code
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: System number
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: System number
Remedy:
Execute an INIEVNT instruction before executing an event related instruction.
Description:
Sub Code: System number
Remedy:
This instruction cannot be executed in the system job. Correct the job so that the instruction is executed in the user job.
Description:
Sub Code: Gun number
Remedy:
Execute the “SVGUNCL TWC-AE”, and then execute the “SVGUNCL TWC=BE”.
Description:
The multi-layer welding function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The observer function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The TURBO function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The COMARC function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The conveyor/press synchronization function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The shared motion function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The layer motion function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The general sensor function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The servo float function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The laser cutting function (with small circle cutter) is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The motor gun function (for spot welding application) is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The speed control function (VCON/VCOF) is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The servo hand function (for handling application) is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The laser cutting function (for form cutting operation) is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The series communication function between the systems (PSEND/PRECV) is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The motion extension function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The bending function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The ME-NET function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The MEMO-PLAY function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The 3D-SHIFT function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The Equalization function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The press synchronization function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The roller hem function is not used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An attempt was made to execute an undefined instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The teaching points are incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The teaching points for user-coordinate turning are incorrect.
Remedy:
Among three taught points in the teaching position. Teach the three points again so that they do not lie in the straight line.
Description:
The robot axis is not specified for the control group of the job to prepare the user coordinates.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Position data error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Setting error of the slave group for user coordinate conversion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The distance could not be monitored when executing a move instruction.
An attempt was made to execute MOVJ/MOVS instruction in arc retry or restart operation.
Remedy:
Check the following settings.
Description:
Sub Code: Press characteristic file number
Remedy:
Set the status of press characteristic file to be used in the job to “Used State.”
Description:
Sub Code: Press characteristic file number
Remedy:
Set the press resolution data to be used in the job.
Content:
The servo float mode could not be reset when executing a FLOATOF instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The control group for the motor gun is not set.
Remedy:
Set the “motor gun axis” in the control group setting of maintenance mode.
Description:
Sub Code: Welder number
Remedy:
Correct the welder number set in the gun characteristic file.
Description:
Sub Code: Welder number
Remedy:
Check the following settings.
Content:
Incorrect setting of spot welding start timing
For motor gun, the welding timing was set to “After First Pressure” while no 2nd pressure was set.
Remedy:
Check the following settings.
Content:
The gun control mode could not be set at SVSPOT/SVGUNCL instruction execution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The gun control mode could not be released at SVSPOT/SVGUNCL instruction execution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Welder number
Remedy:
Check the settings for the timer conductor where the welding error occurred.
Description:
No availability in anticipation control
Remedy:
Maximum simultaneous execution number of anticipation control is twenty. Correct the settings for the job so that it is within twenty.
Description:
The anticipation data exceeded the maximum length.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
anticipation control did not complete within the setting time.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
Anticipation could not be executed at re-painting.
No return step in re-painting function after emergency stop.
Remedy:
Operate the manipulator to the start position of the step where the alarm occurred, and then re-execute.
Description:
Incorrect setting of OT output number for anticipation output file
Remedy:
Check the setting value of OT output number.
Description:
Incorrect setting of OG output number for anticipation output file
Remedy:
Check the setting value of OG output number.
Content:
An invalid gun type is set.
The mode impossible to control is set for the gun.
Remedy:
Check the settings for the motion mode set to the gun.
Content:
An error occurred when executing a STRWAIT instruction.
No confirmation signal specified in the stroke change confirmation instruction was input within the set time.
Remedy:
Check the cause such as defective limit switch.
Content:
The encoder (PG) power supply could not be turned ON.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
A GUNCHG instruction was executed in the system configuration that did not allow the gun change function.
Remedy:
Validate the gun change parameter.
Description:
A GUNCHG/PICK instruction was executed while the motor gun motor was servo ON.
Remedy:
Execute GUNCHG/PICK instruction when the motor gun motor is servo OFF.
Description:
A GUNCHG/PICK instruction was executed while the ATC was in unchuck status.
Remedy:
Execute GUNCHG/PICK instruction when the ATC is in chuck status.
Description:
A GUNCHG/PLACE instruction was executed while the ATC was in unchuck status.
Remedy:
Execute GUNCHG/PLACE instruction when the ATC is in chuck status.
Description:
The encoder power supply could not be turned ON when executing a GUNCHG/PICK instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The encoder power supply could not be turned OFF when executing a GUNCHG/PLACE instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The gun number specified by the GUNCHG instruction did not agree with the gun identification signal.
Remedy:
Check the following settings.
Description:
The 1st gun axis selection signal is not set when executing the twin-wrist gun change.
Remedy:
Check the 1st gun axis selection signal setting.
Description:
The right and left gun axis selection signals were duplicated when executing the twin-wrist gun change.
Remedy:
Check the setting for the gun axis selection signal.
Description:
The control group for gun axis is not set in the gun change job.
Remedy:
Check the settings for the control-group of the job.
Description:
Multiple manipulators are not set in the gun change job.
Remedy:
Check the settings for the control-group of the job.
Content:
When executing the wear correction operation, the reference position of wear correction was not registered under the condition that “Specific input: overwriting reference position of wear detection” was turned OFF.
Remedy:
Resister the reference position of wear correction.
Content:
The control group was not set for the servo hand control.
Remedy:
Set the “servo hand axis” in the control group setting of maintenance mode.
Content:
The speed control mode could not be set at VCON instruction execution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The speed control mode could not be released at VCON instruction execution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The servo hand control mode could not be set at SHPICK instruction execution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The servo hand control mode could not be set at SHPLACE instruction execution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting for radius is incorrect.
(1) For a circle, it is incorrectly set as: radius <= 0, radius < minimum radius value, or radius > maximum radius value.
(2) For an ellipse, it is incorrectly set as: radius <= 0, radius < minimum radius value/2, or radius > (maximum radius/2 - width/2).
Remedy:
Check the following settings.
Description:
The setting for width is incorrect.
(1) For a rectangle, it is incorrectly set as: width < 1.0, width > sqrt (maximum diameter2 - height2), or width > maximum diameter.
(2) It is incorrectly set as: width < 0, width > maximum diameter -2 * radius.
Remedy:
Check the following settings.
Description:
The setting for height is incorrect.
For a rectangle, it is incorrectly set as: height > maximum diameter, height < minimum diameter/2, or height > sqrt (maximum diameter2 - width2).
Remedy:
Check the following settings.
Description:
The setting for the corner radius is incorrect.
For a rectangle, it is incorrectly set as: corner radius > width/2 or corner radius > height/2.
Remedy:
Check the following settings.
Description:
The setting for overlap is incorrect.
(1) For a rectangle, it is incorrectly set as overlap > width/2.
(2) For a circle, it is incorrectly set as overlap > ABS (2Pi * radius).
(3) For an ellipse, it is incorrectly set as overlap > Pi * radius +ABS (width/2).
Remedy:
Check the following settings.
Description:
The setting for the cutting speed is incorrect. It is set as the cutting speed > maximum linear speed.
Remedy:
Check the following settings.
Description:
Coordinated motion cannot be used with the Form Cutting motion.
Remedy:
Do not use the coordinated motion.
Description:
Zero or a negative value is set in the minimum diameter parameter (S1CxG063) for the Form Cutting motion.
Remedy:
Check the following settings.
Description:
Zero or a negative value is set in the maximum diameter parameter (S1CxG064) for the Form Cutting motion.
Remedy:
Check the following settings.
Description:
Although “PLACEMENT” or “AUTO” is set for the start point designation on the FORM CUT SETTING window, the FORMAPR instruction was not executed.
Remedy:
Execute the FORMAPR instruction.
Description:
The Cut file setting of the FORMAPR instruction is different from that of the FORMCUT instruction.
Remedy:
The Cut file settings of FORMAPR and FORMCUT instructions must be same.
Description:
A FORMAPR instruction was used for the conventional FORMCUT instruction.
Remedy:
Check the following settings.
Description:
A form other than a circle, rectangle, and ellipse was designated for the conventional FORMCUT instruction.
Remedy:
Check the following settings.
Description:
The radius data setting for special circular interpolation is incorrect. It is incorrectly set as the radius <= 0.
Remedy:
Check the following settings.
Description:
The arc center coordinates could not be calculated at special circular interpolation. Incorrect teaching may be the cause.
Remedy:
Check the following settings.
Description:
The averaging time at special circular interpolation motion is too short.
Remedy:
Check the following settings.
Description:
Because the designated plane included reference points at special circular interpolation motion, the arc center coordinates could not be calculated. Incorrect teaching of the reference point 2 may be the cause.
Remedy:
Check the following settings.
Description:
The arc center position is not set for the special circular interpolation motion.
Remedy:
Check the settings for the reference point 1 as the arc center position.
Description:
An attempt was made to re-execute the FORMCUT instruction after interrupting it.
Remedy:
Re-execute the move instruction executed before the FORMCUT instruction, and then execute the FORMCUT instruction again.
Description:
Incorrect information of reference position data for offline position data conversion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect user-coordinate number designation in the standard position data for offline position data conversion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect reference-point data for offline position data conversion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The standard position data for offline position data conversion could not correctly be calculated.
Remedy:
The variable position may be out of the robot motion range. Check if the variable position is within the robot motion range.
Description:
Incorrect pulse incremental value for offline position data conversion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The position data could not correctly be added by the pulse incremental value at the offline position data conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect Cartesian incremental value for offline position data conversion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The position data could not correctly be added by the Cartesian incremental value at the offline position data conversion.
Remedy:
The variable position may be out of the robot motion range. Check if the variable position is within the robot motion range.
Description:
The position conversion could not be done in the designated coordinate system at the offline position data conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect incremental value of angle for offline position data conversion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The position data could not correctly be added by the incremental value of angle at the offline position data conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The reverse shift value for 3D shifting could not correctly be calculated at the offline position data conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The reverse shift value for 3D shifting could not correctly be added at the offline position data conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The reverse shift value could not correctly be calculated at the offline position data conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The reverse shift value could not correctly be calculated at the offline position data conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The 3D shifting value could not correctly be added at the offline position data conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The shift value could not correctly be added at the offline position data conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No reference point is specified for the offline position data conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The positions for the mirror shift function could not correctly be calculated at the offline position data conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The positions could not correctly be converted for the mirror shift function at the offline position data conversion.
Remedy:
The variable position may be out of the robot motion range. Check if the variable position is within the robot motion range.
Description:
The expansion positions for the mirror shift function could not correctly be converted at the offline position data conversion.
Remedy:
The variable position may be out of the robot motion range. Check if the variable position is within the robot motion range.
Description:
Incorrect designation of coordinates for a new mirror-shift conversion function at the offline position data conversion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect designation of the occupation control group for welding path shift function.
Remedy:
(1) Reset the alarm, select [UTILITY]-[ARC SHIFT CANCEL], and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The inverse shift data for welding path shift function could not correctly be calculated.
Remedy:
(1) Reset the alarm, select [UTILITY]-[ARC SHIFT CANCEL], and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The inverse shift data for welding path shift function could not correctly be added.
Remedy:
(1) Reset the alarm, select [UTILITY]-[ARC SHIFT CANCEL], and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The parameter setting for the universal input group number is incorrect.
Remedy:
Check the settings for the AxP011.
Description:
An attempt was made to issue the command while the servo control processing has not completed.
Sub Code: Servo CPU bit number
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Gun condition file number
Remedy:
Complete the gun condition file setting.
Description:
Sub Code: Welder number
Remedy:
Remove the cause of wire stick.
Content:
No home position correction data of specified axis.
Remedy:
Check the following settings.
Description:
The difference between the current tool constant and a new set value exceeded the allowable range (parameter set value).
Remedy:
Check the following settings.
Description:
The difference between the monitoring condition of tool and a new set value exceeded the allowable range (parameter set value).
Remedy:
Check the following settings.
Content:
The memory area of global variable exceeded the limit value.
An error occurred in the value of parameter that defines the number of global (user) variables.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The execution macro job is not set.
Remedy:
Check the settings for execution macro job.
Description:
The suspend macro job is not set.
Remedy:
Check the settings for suspend macro job.
Description:
An attempt was made to start the job that could not be started by the macro instruction.
Remedy:
Check the settings for macro job.
Description:
An error occurred in the operation process of job call stack when the execution of macro instruction was cancelled.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect macro number
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The contents of the macro instruction registered on the line where the alarm occurred do not match the contents of the macro job.
Remedy:
Delete the macro instruction for the line where the alarm occurred and re-register the macro instruction.
Description:
The job argument is not set.
Remedy:
Check the settings for jobs.
Description:
No number of the specified job argument
Remedy:
Check the settings for jobs.
Description:
The data types of job argument disagreed.
Remedy:
Check the settings for jobs.
Description:
The memory play file was being used in another system.
Remedy:
Check the setting of the used memory play file number.
Description:
The control group in the memory play file did not agree with the control group of execution job.
Remedy:
Check the control group setting of the used memory play file.
Description:
An attempt was made to clear the memory play file by a CLEAR instruction before having executed a MEMOF instruction.
Remedy:
Execute the MEMOF instruction, and then execute the CLEAR instruction.
Description:
Failed to read the memory play sampling data.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed to write the memory play sampling data.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed to seek the memory play sampling data.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed to read the memory play file.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect mode setting at memory play sampling
Remedy:
Check the settings for the memory play mode.
Description:
Incorrect designation of the control group at memory play sampling
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Designation of the control group in the memory play file did not agree with the designation of the control
group at MEMON instruction execution (when the start point was specified).
Remedy:
Check the number of the memory play file for use.
Description:
Designation of the control group in the memory play file did not agree with the designation of the control group at MEMON instruction execution (at initialization).
Remedy:
Check the number of the memory play file for use.
Description:
designation of the control group in the memory play file did not agree with the designation of the control
group at MEMON instruction execution (at continue).
Remedy:
Check the number of the memory play file for use.
Description:
It started reproducing though it did not record.
Remedy:
Record and then play.
Description:
Correction amount to record is out of the allowable range.
Remedy:
Correct the position of object workpieces so that the correction amount fall within allowable range.
Description:
The number of recorded correction-amount exceeded the limit.
Remedy:
Correct the job so that the movement section of memory play object is shorter.
Description:
Memoplay file Create error (REC)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Memoplay debug error C_BANK.func_ctrl (initial)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Memoplay debug error C_BANK.func_ctrl (continue)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Memoplay debug error C_BANK RT_BANK.func_ctrl (continue)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Memoplay debug error MOVL, MOVC (continue)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Memoplay debug error Same point, moving amount is zero (continue)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Memoplay debug error Dividing number error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
An error occurred when executing a OPTON instruction.
The number of times that the OPTON instruction was executed exceeded the limit value.
Remedy:
Check the settings for the OPTON instruction. OPTON instruction can use only the function to five simultaneously.
Description:
Sub code: the number of synchronizations of the first executed TSYNC
Remedy:
Check the settings for the number of synchronizations of the TSYNC instruction.
Description:
The function designation parameter is not set.
Remedy:
Check the settings for the function designation parameter.
Description:
No sealer gun axis exists at the job for which the sealer gun control was attempted to be executed.
Remedy:
Check the settings for the control-group of the job.
Description:
No robot axis exists at the job at which an attempt was made to execute sealer gun control.
Remedy:
Check the settings for the control-group of the job.
Description:
Incorrect designation of the control method for sealer gun control
Remedy:
Set either “1” or “2” for PRM1 control method designation of the OPTON instruction.
Description:
Incorrect designation of the control method for sealer gun control
Remedy:
If “1” is set for PRM1 of the OPTON instruction, set the PRM2 needle position designation to a value between 0 and 100.
Description:
Incorrect designation of the sealing width for sealer gun control
Remedy:
If “2” is set for PRM1 of the OPTON instruction, set PRM2 sealing width designation to a value between 0 and 30.
Content:
The servo sealer gun condition file is not set.
Remedy:
Check the settings for servo sealer gun condition file.
Description:
An attempt was made to command a job whose control group was in I/O axis motion.
Remedy:
Check the following settings.
Description:
The file could not be switched because of incorrect start point designation.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The control group with which the axis shifting is performed disagrees with the control group set for the axis shifting function in the calibration file.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The calibration file number for axis shifting function is out of the applicable range.
Remedy:
Correct the settings for the OPTON instruction tag so that value of the file number specification is 1 to 32.
Description:
For the CSL15D manipulator, the motion speed of S- and U-axes exceeded the upper limit.
Remedy:
Check the following settings.
Description:
For the CSL15D manipulator, S- and U-axes were going to move regardless of the limit speed “0” when the positions of L- and R-axes exceeded the upper limit.
Remedy:
Teach the positions of L- and R-axes again so that S- and U-axes can move.
Description:
For the tool shift with Euler angle plus or minus90 degrees, the shift value for axes other than Y-axis is set.
Remedy:
Check if the shift value is setting for Y-axis only.
Description:
Sub Code: Designated registration number
Remedy:
Check the settings for the job registration table.
Description:
Sub Code: Group(Interfering)&Axis(Interfering)&Group(Interfered)&Axis(Interfered)
Remedy:
Check the following settings.
Description:
Sub Code: Welder number
Remedy:
Check the settings for welding completion signal.
Description:
Sub code: Group&Axis(Interfering)&Axis(Interfered)
Remedy:
Check the following settings.
Description:
An attempt was made to obtain the step that used a local position type variable. (The step with local position type variable cannot be fetched. Example: MOVJ LP000 VJ=25.00)
Remedy:
Check the settings for the GETPOS instruction.
Description:
An attempt was made to obtain the step that used a local position type variable. (The step with local position type variable cannot be fetched. Example: MOVJ LP000 VJ=25.00)
Remedy:
Check the settings for the GETPOS instruction.
Description:
The specified step did not exist.
Remedy:
Check the settings for the GETPOS instruction.
Description:
An attempt was made to obtain the step without CTP(CTPP) tag.
Remedy:
Check the settings for the GETPOS instruction.
Description:
An attempt was made to obtain the step with CTP(CTPP) tag of variable specification. (The step with CPT(CTPP) tag of variable specification cannot be fetched.)
Remedy:
Check the settings for the GETPOS instruction.
Content:
Incorrect setting of amount of fillings.
Remedy:
Check the setting for the amount of fillings.
Description:
No file
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No directory
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
There was no directory entry after this point.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No file name
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
File presence error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect file name
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The disk is full.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The directory is full.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
I/O error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Invalid handle
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Handle overflow
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
File has already been opened.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
File attribute error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Open mode error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The hardware disk with large capacity is used.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The door is open.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The disk is write-protected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Card controller access error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No card
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Card drive information readout error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Partition table error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No drive number
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No specified partition number
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Cluster size error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect number of sectors
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sector/byte error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Card not applicable for I/O
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Unsupported version
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting register did not exist.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Card not applicable for ATA
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Double chain error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Media error (not fixed disk)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
ATA command incomplete
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sector read command error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sector write command error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
An error occurred at S-axis high-speed rotation.
The S-axis rotation radius was below the lower limit.
Remedy:
Check the settings for the limit distance for S-axis rotation center motion (S1CG067).
Description:
Sub Code: Gun number
Remedy:
Check the settings for the gun identification signal.
Description:
Sub Code: Duplicated variable number
Remedy:
Check the settings for the written destination variable numbers.
Description:
The group change parameter was invalid.
Remedy:
Validate the group change parameter.
Description:
The GRPCHG instruction was executed while the external axis motor was servo ON.
Remedy:
Execute the GRPCHG instruction when the external axis motor was servo OFF.
Description:
The GRPCHG instruction was executed in unchuck status.
Remedy:
Execute the GRPCHG instruction in chuck status.
Description:
The group identification signal was not received.
Remedy:
Check the settings for group identification signal.
Description:
The specified control group number and the group identification number were unmatched.
Remedy:
Check the settings for the specified control group number.
Description:
The encoder PG power supply was OFF when the GRPCHG was ON.
Remedy:
Turn ON the encoder PG power supply when GRPCHG is ON.
Description:
The encoder PG power supply was ON when the GRPCHG was OFF.
Remedy:
Turn OFF the encoder PG power supply when GRPCHG is OFF.
Description:
The control group that corresponded to the received group identification signal did not exist.
Remedy:
Check the settings for group identification signal.
Description:
Sub Code: The overlapped gun number
Remedy:
Check the settings for gun numbers.
Description:
Sub Code: Control group and axis
Remedy:
Check if the speed is hold down by the speed override and special operations etc.
Description:
Sub Code: Linear scale characteristic file number
Remedy:
Complete the settings for the linear scale condition file.
Description:
An error occurred when executing a FOLLOW instruction.
An attempt was made to re-execute the FOLLOW instruction after interrupting it.
Remedy:
Re-execute the move instruction executed before the FOLLOW instruction, and then execute the FOLLOW instruction again.
Content:
The manipulator motion speed exceeded the limit during the Following motion.
With the specified bending speed, the manipulator motion speed exceeds the maximum speed.
Remedy:
Check the following settings.
Description:
Sub Code: The related control-group
Remedy:
Check the settings for control group specified by the CALL instruction.
Description:
Sub code: Gun number
Remedy:
Weld the spot by thickness within allowable range.
Description:
Sub Code: Conveyor characteristic file number
Remedy:
Check the workpiece presence/absence and data settings for the synchronization section.
Description:
Sub Code: Conveyor characteristic file number
Remedy:
Check the workpiece presence/absence and data settings for the synchronization section.
Description:
The conveyor moving amount is not specified for the SYMOVJ motion.
Remedy:
Set the conveyor moving amount for the SYMOVJ motion.
Description:
An error occurred in the preparation process of the manipulator motion start position for the SYMOVJ motion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the preparation process of the manipulator motion end position for the SYMOVJ motion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
No axis data of control group to be disconnected
Remedy:
Check the settings for PSTART instruction.
Description:
An attempt was made to disconnect a control group other than the occupation control group during prereading processing.
Remedy:
Check the settings for PSTART instruction.
Description:
An attempt was made to disconnect a control group other than the occupation control group when executing a PSTART instruction.
Remedy:
Check the settings for PSTART instruction.
Description:
Sub Code: The disconnected control group used by a move instruction
Remedy:
Correct the teaching so that the control group disconnected by itself is not to operate for move instruction of own system.
Description:
The controller could not send an instruction to the welder because the welder was busy in processing.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Welding current error at welding is completed successfully.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Abnormal code error at welding is completed successfully.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Welding command process exceptional error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The specified welder number (system) could not be found.
Remedy:
Confirm the specified welder number (system) and the setting.
Content:
Hover weaving could not be executed.
The hover weaving is disabled in coordinated motion.
Remedy:
Check the settings for jobs.
Description:
Motion range file transfer error
Remedy:
Check if the motion range file is correctly set.
Description:
Part motion range file transfer error
Remedy:
Check if the part motion range is correctly set.
Description:
Sub Code: Interference control group number & interference axis & interference area number.
Remedy:
Check the setting of the teaching position of the manipulator.
Content:
Couldn’t clear the Max Torque when performing TRQCLS.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The setting of the palletizing condition configuration file is incomplete.
Remedy:
Set the palletizing condition setting file to “Completed.”
Description:
Palletize completion universal output number range exceeds the limit.
Remedy:
Change the palletize completion universal output signal number of the palletizing condition setting file in the user output signal point of contact number.
Description:
During the palletize start instruction execution, the palletize start instruction is executed again (double execution).
Remedy:
Delete the palletize start instruction in the palletize section.
Description:
The value of the palletizing number present value output register (or I variable) is more than the total number output register (or I variable).
Remedy:
Check if the palletizing number of current position output register (or I variable) and total number of output register (or I variable) is not changed by another function.
Description:
Palletize completion universal output signal is turned ON at palletize start instruction execution.
Remedy:
Reset the palletize completion universal output signal.
Description:
Palletize end instruction is not registered.
Remedy:
Register the palletizing end instruction.
Content:
Couldn’t set to Constant speed torque measure mode when performing MEASON TRQ.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
Couldn’t release the Constant speed torque measure mode when performing MEASOF TRQ.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An attempt was made to change the value of the analog input register.
Remedy:
The SETREGM instruction cannot change the analog input register values. Correct the setting of tag that specifies register number of SETREG instruction.
Description:
An attempt was made to change the value of the register currently used by TMR/CNT.
Remedy:
The SETREGM instruction cannot change the register values used in TMR/CNT. Correct the setting of tag that specifies register number of SETREG instruction.
Description:
An attempt was made to change the value of the register currently used by TMR/CNT.
Remedy:
Correct the setting of tag that specifies register number of SETREG instruction.
Description:
An attempt was made to acquire the value of the register not existing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An attempt was made to change a parameter other than the cube-related or the analog output corresponding to speed-related parameter.
Remedy:
The SETPRM instruction cannot change the parameter values other than the parameter related to the cube or the analog output corresponding to speed. Correct the setting of tag that specifies parameter number of SETPRM instruction.
Description:
The SETPRM instruction was executed while another system was in execution.
Remedy:
The SETPRM instruction cannot execute while another system is operating. Correct the job.
Description:
The correction amplitude value did not fall in the limit range.
Remedy:
Correct the settings for “groove width correction limit value” specified for S2C1259 and 1260.
Description:
The taught speed was going to exceed the limit during the multi arm simultaneous operation.
Remedy:
Reduce the teaching speed of the step where the alarm occurred to the speed limit or less.
Description:
An error occurred in the interface with the servo section during chip dress monitoring.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in the interface with the servo section when the chip dress monitoring was canceled.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: File number
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the press characteristic file in maintenance mode, and then load the press characteristic file saved in the external memory device.
Description:
The press synchronous program could not be executed.
Remedy:
Make sure that you are not accessing the same variable in the press synchronous program.
Description:
The target position could not be calculated in correcting the position.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The number of WAIT instructions used in the press synchronous program exceeds the maximum number.
Remedy:
Reduce the WAIT instruction used in the press synchronous program.
Description:
Could not get WAIT instruction information.
Remedy:
Make sure that there is a move instruction with ENC tag before WAIT instruction.
Description:
Unable to set the correction data for the press synchronous control.
Remedy:
The alarm occurs if the MOVE instruction except MOVJ with ENC tag is operated during Press synchronous control.
Reset the press synchronous control by the following operations to operate the MOVE instruction expect MOVJ with ENC tag.
Description:
The number of CHGPRSJOB instructions used in the press synchronous program exceeds the maximum number.
Remedy:
Reduce the CHGPRSJOB instruction used in the press synchronous program.
Description:
Could not get CHGPRSJOB instruction information.
Remedy:
Make sure that there is a move instruction with ENC tag before CHGPRSJOB instruction.
Description:
Could not execute press synchronous program trajectory plan.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Could not get press position.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Update of press position was interrupted during press synchronization operation.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
“WAIT position operation general purpose output number output register number” is invalid.
Remedy:
Please set a value other than 0 for the parameter “SE92”.
Description:
The specified WAIT signal does not exist.
Remedy:
Please check whether the specified WAIT signal exists.
Description:
In the two press synchronous programs that can be switched during press synchronous operation, the number of registered WAIT instructions does not match.
Remedy:
Match the number of WAIT instructions to be registered.
Description:
In the two press synchronous programs that can be switched during press synchronous operation, the registration positions of the WAIT instruction do not match.
Remedy:
Register a WAIT instruction between the same press angle steps
Description:
In the two press synchronous programs that can be switched during press synchronous operation, the registration positions of the CHGPRSJOB instruction do not match.
Remedy:
Register a CHGPRSJOB instruction between the same press angle steps
Description:
Press sync setup is not complete.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ACP02 board. Save the CMOS.BIN before replacing the board to be safe.
Description:
Failed to prepare to perform press synchronization.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Can not communicate with ACP02 board. The response from the segment section and the handler section ceased.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ACP02 board. Save the CMOS.BIN before replacing the board to be safe.
Description:
Can not communicate with ACP02 board. The response from the handler section ceased.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ACP02 board. Save the CMOS.BIN before replacing the board to be safe.
Description:
Can not communicate with ACP02 board. The response from the segment section ceased.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ACP02 board. Save the CMOS.BIN before replacing the board to be safe.
Description:
When correcting the position, the current value of the robot is outside the position range check.
Remedy:
Check the current value of robot at position correction and SxE85: position correctable range (at position correction).
Description:
At the start of synchronous operation, the current value of the robot is outside the position range check.
Remedy:
Check the current value of the robot at the start of synchronous operation and SxE86: position correctable range (during synchronous operation).
Description:
Move instructions other than MOVJ are registered in the synchronization program. Or ENC 1 tag of MOVJ is not used.
Remedy:
Remove moving instructions other than MOVJ from within the synchronization program. Also, please use ENC 1 tag for all MOVJ.
Description:
The move instruction in the synchronous program is one step or more than 361 steps.
Remedy:
Correct the move instruction in the synchronous program from 2 to 360 steps.
Description:
There are steps where the press position registered in MOVJ of press synchronization program is not in ascending order.
Remedy:
Please set the press positions registered in MOVJ of press synchronization program in ascending order.
Description:
The number of robots in the press synchronization program is two or more.
Remedy:
Please set the robot number of press synchronization program to one.
Description:
Press start position exceeded travel amount of 1 cycle(ADV).
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The press position registered in MOVJ of press synchronization program is as follows.
Press position < 0.00
Or
Press position >= 360.00
Remedy:
Please set the press position registered in MOVJ of Press Synchronization Program as follows.
0.00 <= Press position < 360.00
Description:
Press number error(ADV)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
DM_BANK error(ADV)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
ADV Bank Priority Error(ADV)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Last Bank None Error(ADV)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Alarm not occurred error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Search failed error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Bank priority error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Motion command error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
NEXT_CBANK error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Path creation incomplete error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Current position creation error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Position correction alarm not occurring error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Position correction trajectory creation incomplete error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Position correction press number error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Position correction search failure error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Position correction control group specification error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Shift data type error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
At the restart of synchronous operation, the current value of the robot is outside the position range check.
Remedy:
Check the current value of the robot at restarting the synchronous operation and SxE 91: the synchronous operation restartable range.
Description:
Memory access error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Number of steps displayed(ADV)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Number of steps displayed
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The weld length check file is not set.
Remedy:
Complete the settings for the weld length check condition file.
Description:
Sub Code: Gun pressure file number
Remedy:
Match the number of “END WAIT” in the gun pressure file, and the number of “Welding Conditions(WTM)” in the instruction.
Content:
An error was detected at memory check.
The memory for the maintenance prevention file is damaged.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the maintenance prevention file in maintenance mode, and then load the maintenance prevention file saved in the external memory device.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the motor.
(3) If the alarm of “external brake” is occurred. , replace the external brake.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) Lengthen the measurement section.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) Shorten the measurement section.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) Increase the speed specification value of a measurement job or set a small value for BASICV.
Or set a small value for BASICT, or lengthen the measurement section.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) Set a large value for the BASICT, and then check again.
Description:
An attempt was made to set tool for base/station-axis position-type variable.
Remedy:
Check the settings for jobs.
Description:
Sub Code: Signifies the servo board in which the alarm occurred
0000_0001 SV#1
0000_0010 SV#2
0000_0100 SV#3
0000_1000 SV#4
0001_0000 SV#5
0010_0000 SV#6
0100_0000 SV#7
1000_0000 SV#8
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check if there is a ground fault or short circuit in the fan power line.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check if there is a ground fault or short circuit in the fan power line.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check if there is a ground fault or short circuit in the fan power line.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check if there is a ground fault or short circuit in the fan power line.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check if there is a ground fault or short circuit in the fan power line.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check if there is a ground fault or short circuit in the fan power line.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check if there is a ground fault or short circuit in the fan power line.
Description:
Sub Code 1to 8: Signifies the SDCA01 board No. in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check if there is a ground fault or short circuit in the fan power line.
Description:
Sub Code: Control group and axis
Remedy:
Check the following settings.
Description:
Sub Code: Internal control error in software
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, initialize the database of spot weld history.
(3) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control group
Remedy:
Set the operation area of the specified robot correctly.
Description:
The previous command was not completed.
Sub Code: Functional safety board station number.
Remedy:
Reset the alarm, and then try again.
Description:
Sub Code: Control group and axis
Remedy:
Check the following settings.
Description:
Group no., axis and line segment No.
Remedy:
Check the following settings.
Description:
Sub code: Control group and axis
Remedy:
Check the following settings.
Description:
Sub Code: Control group
Remedy:
Check the following settings.
Description:
An error occurred in the parameter write operation.
Remedy:
(1) Reset the alarm.
(2) Try the write operation again.
Description:
An error occurred in the file write operation.
Remedy:
(1) Reset the alarm.
(2) Try the write operation again.
Description:
Write request has timed out.
Remedy:
(1) Reset the alarm.
(2) Try the write operation again.
Content:
An error occurred when recording the data in the ASF01 board.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
An error occurred when recording the data in the ASF01 board.
Remedy:
(1) Select [ROBOT] to open [AXIS RANGE] screen. Set the item to “INVALID” and then cycle the power.
(2) Move the manipulator into the specified range.
(3) Select [ROBOT] to open [AXIS RANGE] screen. Set the item to “VALID” and then cycle the power.
Cause:
ASF01 board failure
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The ASF01 board has detected the manipulator is about to exceed the specified operation area.
Remedy:
(1) Select [ROBOT] to open [AXIS RANGE] screen. Set the item to “INVALID” and then cycle the power.
(2) Move the manipulator into the specified range.
(3) Select [ROBOT] to open [AXIS RANGE] screen. Set the item to “VALID” and then cycle the power.
Cause:
ASF01 board failure
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The ASF01 board has detected a decrease in encoder battery.
Remedy:
(1) Reset the alarm.
(2) Check the operation area.
Content:
The ASF01 board has detected a decrease in encoder battery.
Remedy:
(1) Reset the alarm.
(2) If AL4311 occurred simultaneously with this alarm, execute the trouble shooting for the AL4311.
Description:
Readback value of CPU1 and CPU2 mismatch.
Remedy:
(1) Reset the alarm.
(2) Try the write operation again.
Description:
Another readback request was issued to the readback process. (Parameter)
Remedy:
(1) Reset the alarm.
(2) Try the write operation again.
Description:
Another readback request was issued to the readback process. (File)
Remedy:
(1) Reset the alarm.
(2) Try the write operation again.
Description:
Incorrect file type.
Remedy:
(1) Reset the alarm.
(2) Try the write operation again.
Description:
Incorrect file number.
Remedy:
(1) Reset the alarm.
(2) Try the write operation again.
Description:
Incorrect write data.
Remedy:
(1) Reset the alarm.
(2) Try the write operation again.
Description:
Process order error.
Remedy:
(1) Reset the alarm.
(2) Try the write operation again.
Content:
The manipulator was about to move at the speed faster than specified safety speed (250mm/sec) for TCP.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The manipulator was about to move at the speed faster than specified safety speed (250mm/sec) for flange.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
There was the same point in three points where the calibration had been executed.
Remedy:
Correct the calibration position so that each point is different.
Description:
The three points where the calibration had been executed lie in a straight line.
Remedy:
Check the calibration position so that the three taught points are not aligned in a straight line.
Description:
The three points where the calibration had been executed lie in a straight line.
Remedy:
Check the calibration position so that the three taught points are not aligned in a straight line.
Description:
Incorrect information of standard position data for offline arm bend position data conversion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect user-coordinate number in the standard position data for offline arm bend position data conversion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Incorrect reference-point data offline arm bend position data conversion
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The position data could not be converted correctly/conversely for the standard position data at the offline arm bend position data conversion.
Remedy:
The variable position may be out of the robot motion range. Check if the variable position is within the robot motion range.
Description:
Incorrect pulse incremental value for offline arm bend position data conversion
Remedy:
The variable position may be out of the robot motion range. Check if the variable position is within the robot motion range.
Description:
The position data could not be converted correctly for the pulse incremental value at the offline arm bend position data conversion.
Remedy:
The variable position may be out of the robot motion range. Check if the variable position is within the robot motion range.
Description:
Incorrect Cartesian incremental value for offline arm bend position data conversion
Remedy:
The variable position may be out of the robot motion range. Check if the variable position is within the robot motion range.
Description:
The position data could not be converted correctly for the Cartesian incremental value at the offline arm bend position data conversion.
Remedy:
The variable position may be out of the robot motion range. Check if the variable position is within the robot motion range.
Description:
The position conversion could not be done in the conversion data for offline arm bend position data conversion.
Remedy:
The variable position may be out of the robot motion range. Check if the variable position is within the robot motion range.
Description:
Incorrect incremental value of angle for offline arm bend position data conversion
Remedy:
The variable position may be out of the robot motion range. Check if the variable position is within the robot motion range.
Description:
The position data could not be converted correctly for the incremental value of angle at the offline arm bend position data conversion.
Remedy:
The variable position may be out of the robot motion range. Check if the variable position is within the robot motion range.
Description:
The gravity moment for offline arm bend position data conversion could not be calculated.
Remedy:
The variable position may be out of the robot motion range. Check if the variable position is within the robot motion range.
Description:
The position data could not be converted correctly for the revised conversion data at the offline arm bend position data conversion.
Remedy:
The variable position may be out of the robot motion range. Check if the variable position is within the robot motion range.
Description:
Reference position and target position occupation control-group error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Reference position and target position enabling control-group error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The position data type is not applicable.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Coordinated control-group error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
User coordinates number on the specified tag side error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code
Internal control error in software
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code
Internal control error in software
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
Use memory is lacking and the area could not be obtained.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
Cannot change the mode to PLAY under ENCODER BACK-UP ERROR in ASF01 system.
Remedy:
(1) Change the teach mode.
(2) Reset the alarm, and then try again.
(3) If the alarm occurs again, set to home position.
Content:
ASF01 board has detected that the manipulator has operated when Stopping position monitoring function is enabled.
Remedy:
(1) Check the connection of CNGS1.0 of the NSU.
(2) Turn the power OFF then back ON.
(3) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
PPESP inconsistent
Remedy:
(1) Check the connection of CNGS1.0 of the NSU.
(2) Turn the power OFF then back ON.
(3) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
PPDSW inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
PBESP inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
EXESP inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, check or replace the CNIFA connector and then cycle the power again.
Description:
EXDSW inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, check or replace the CNIFA connector and then cycle the power again.
Description:
SAFF inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, check or replace the CNIFA connector and then cycle the power again.
Description:
FST inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
UNUSED_1 inconsistent
UNUSED_1 is not used. Therefore, in this case, the board is damaged.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SON inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
BON inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SVMAIN inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
MODE0 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
MODE1 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SSP inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
WDGER_1 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
WDGER_2 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SFRDY1 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SFRFB1 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
KMMB1 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
UNUSED_3 inconsistent
UNUSED_3 is not used. Therefore, in this case, the board is damaged.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SFRDY2 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SFRFB2 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
KMMB2 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
UNUSED_2 inconsistent
UNUSED_2 is not used. Therefore, in this case, the board is damaged.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SFRDY3 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SFRFB3 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
KMMB3 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
UNUSED_5 inconsistent
UNUSED_5 is not used. Therefore, in this case, the board is damaged.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SFRDY4 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SFRFB4 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
KMMB4 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
UNUSED_4 inconsistent
UNUSED_4 is not used. Therefore, in this case, the board is damaged.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
GSIN0 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, check or replace the CNGS1/CNGS2 connector and then cycle the power again.
(3) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
GSIN1 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, check or replace the CNGS1/CNGS2 connector and then cycle the power again.
Description:
SFSMDOFB0 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SFSMDOFB1 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SFSMDI0 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SFSMDI1 inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replace the unit to be safe.
Description:
SFULI inconsistent
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, check the short plug S1 to S8 on the board and then cycle the power.
Description:
SFULFB inconsistent
This may occur in accordance with other alarms.
Remedy:
Execute the trouble shooting for the alarms which simultaneously occurred with this alarm.
Description:
Control data error occurred at prereading. (Function the timing control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control data error occurred. (Function the timing control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Index number of the target does not exist.
(Function the timing control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Bank number of the target does not exist. (Function the timing control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control data size over. (Function the timing control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control index overflow. (Function the timing control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The control-group of surveillance does not exist. (Function the timing control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Instruction index overflow. (Function the timing control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when calculate a feedback position. (Function the timing control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The control-group of the target which supervises a position does not exist. (Function the timing control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Waiting time exceeded the limit. (Function the timing control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
watching information settings incomplete
(Function the timing control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Delay control impossible
(Function the timing control)
Remedy:
Please change the settings so as not to delay control.
Description:
Execution control request settings incomplete
(Function the timing control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Instruction that can not coexist with FPL/+DOUT/+PULSE was used
Remedy:
(1) Check the following settings.
Description:
Monitor error occurred. (Function the timing control)
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Executed step designation error
Remedy:
(1) Check the following settings.
Description:
Sub Code: Gun number
Remedy:
Please complete the setting of MOTOR GUN AUTO TUNING FILE as the following operations.
Description:
Sub Code: Welder number
Remedy:
(1) Reset the alarm, and then try again.
NOTE) When trying the job again, the manipulator returns to the previous welding point where the spot welding wasn’t completed normally and welds again there.
(2) If the alarm occurs again, check the following setting of the timer.
Content:
Arc failure signal was input from the welder even though ARCON is not performed.
Remedy:
It will be automatically reset after 10 seconds. Then, start again.
Content:
24V fuse blown is detected in the AEW01
Remedy:
Replace the fuse on the AEW board.
Description:
Sub Code: AEW board number
Remedy:
Replace the AEW board.
Content:
External power (24V) for welding board (AEW01) is OFF
Remedy:
Check if the 24V line that is input for AEW board is correctly wired.
Description:
Sub Code: AEW board number
Remedy:
Replace the AEW board.
Description:
Failed in the generation of the CIP server task.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the ID take of the CIP server task.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the generation of the class entry table.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Library initialize error.
Remedy:
Check the following settings.
Description:
Failed in the generation of the access process.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect undefined error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect sever function started processing.
Remedy:
Check the following settings.
Description:
Detect request error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect memory error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect mail send error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect CIP answer error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect CIP server task mail receive error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect CIP server task request data error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect CIP server task send error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
IP address duplicated.
Remedy:
(1) Reset the alarm, and then try again.
(2) The IP address is duplicated with the YRC1000 controller. Confirm the IP address of the communication target.
(3) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the generation of the RC connect management task.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the generation of the RC server task.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the generation of the file server task.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the generation of the command backup task.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ACP01 board. Save the CMOS.BIN before replace the board to be safe. Replace the ACP01 board, and then remove the SD CARD from the failure ACP01 board to insert it into the new ACP01 board.
Description:
Failed in the Initializing process of HIGH-SPEED ethernet server log.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ACP01 board. Save the CMOS.BIN before replace the board to be safe. Replace the ACP01 board, and then remove the SD CARD from the failure ACP01 board to insert it into the new ACP01 board.
Description:
Failed in the generation of the command relay function server task.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the request take of the RC connect management task.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the endian conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Received data area overflow.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the request error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the request error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC connect management task, undefine error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the ID take of the RC server task.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the mail take of the RC server task.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC server task, request mail data error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Answer data area overflow.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC server task, receive data area overflow.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC server task, undefined error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file server task, mail receive error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file server task, request mail data error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
IP address duplicated.
Remedy:
(1) Reset the alarm, and then try again.
(2) The IP address is duplicated with the YRC1000 controller. Confirm the IP address of the communication target.
(3) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the endian conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file server task, receive data area overflow.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC connect management task , send error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the endian conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect RC server task send error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the endian conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect file server task send error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the endian conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file server task, answer data error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the endian conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file server task, answer data area overflow.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the status error occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file server task, undefined error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file sever task, file close error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the task ID acquisition from HIGH-SPEED ethernet server log.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the semaphore acquisition from HIGH-SPEED ethernet server log.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the data acquisition from HIGH-SPEED ethernet server log.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect message library initialize error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the generation of the file function task.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the generation of the RC function task.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect I/F data error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect undefined error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file task, undefined error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, undefined error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, request command error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In RC task, there is not the class entry of the request command.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In RC task, there is not the service entry of the request command.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a high speed Ethernet task, request mail error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a high speed Ethernet task, request command error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file task, mail receive error occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file task, file reading error occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file task, file writing error occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file task, request send error occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the endian conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file task, reply packet clear error occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the take of the reply packet data error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the endian conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file task, time out occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file task, receive data area overflow occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file task, received data unmatched.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file task, receive data size overflow occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file task, received data size set to zero occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file task, reply head error occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a file task, reply status error occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, interface request error occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, interface answer error occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, interface data area overflow occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, interface data writing error occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, time out occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect data error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect exclusive process error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect time out.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Setting error
Remedy:
Reset the alarm, and confirm whether the following parameter is set to zero.
Description:
Detect exclusive process error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, request send error occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the endian conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, reply packet error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, reply take error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in the endian conversion.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detect time out.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, receive data area overflow detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, received data unmatched.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, received data size over.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, receive data size zero detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, reply head error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
In a RC task, reply status error detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
vibration suppression filter did not complete within the specified time.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The tool number specified by the safety signal does not match the tool number of robot.
Remedy:
(1) Reset the alarm.
(2) Set the tool number of robot as the same one specified by the safety signal.
Description:
Sub Code: Control group number & tool data & tool number.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
TM variable number exceeded the limit.
Remedy:
Check the TM variable number used in the job, and then correct the job to fall within the range of TM variable number(0-59).
Description:
Same TM variable set up as “LOCAL” was used in different tasks.
Remedy:
Correct the job not to use the same TM variable set up as “LOCAL” in different tasks.
Description:
The I/O signal number set up in the “SETTM SETUP FILE” cannot be carried out.
Remedy:
Check the I/O signal number set in the “SETTM SETUP FILE”, and then correct it within the effective setting range.
Description:
Conveyor condition support file(WORK ID shift) is not set.
Remedy:
Set “Use state” of conveyor condition support file(WORK ID shift) to “1: Use.”
Description:
Conveyor condition support file(WORK IN/OUT shift) is not set.
Remedy:
Set “USED STATUS” of conveyor condition support file(WORK IN/OUT shift) to “1: Use.”
Description:
Conveyor condition file is not set.
Remedy:
Set “USED STATUS” of conveyor condition file to “1: Use.”
Description:
Conveyor condition support file(Start shift) is not set.
Remedy:
Set “USED STATUS” of conveyor condition support file(Start shift) to “1: Use.”
Description:
“WORK ID signal” of the Conveyor condition support file(WORK ID shift) is not set
Remedy:
Set “WORK ID signal” of Conveyor condition support file(WORK ID shift)
Description:
“WORK IN/OUT signal” of the Conveyor condition support file(WORK IN/OUT shift)is not set
Remedy:
Set “WORK IN/OUT signal” of Conveyor condition support file(WORK IN/OUT shift)
Description:
“WORK ID signal” of the Conveyor condition support file(WORK ID shift)is not set
Remedy:
Set “WORK ID signal” of Conveyor condition support file(WORK ID shift)
Description:
“WORK IN/OUT signal” of the Conveyor condition support file(WORK IN/OUT shift)is not set
Remedy:
Set “WORK IN/OUT signal” of Conveyor condition support file(WORK IN/OUT shift)
Description:
The file number is wrong.
An attempt was made to record again the file being recorded by IBGNSTART instruction.
Remedy:
Set a number of the file in IBGNSTART instruction, so that the file being recorded does not repeat.
Description:
The number of robot in the JOB is wrong.
An attempt was made to record the file in the JOB including robots more than two.
Remedy:
Correct the JOB, so that IBGNSTART instruction is used in the JOB of one robot.
Description:
The number of external axis(STATION or BASE) in the JOB is wrong.
An attempt was made to record the file in the JOB including external axis(STATION or BASE) more than two.
Remedy:
Correct the JOB, so that IBGNSTART instruction is used in the JOB of one external axis(STATION or BASE).
Description:
IBGNEND instruction is not registered.
Remedy:
Register IBGNEND instruction in the same job after the line where IBGNSTART instruction was registered.
Description:
IBGNEND signal is not turned OFF before a specified time at the time of IBGNSTART instruction executed.
Remedy:
Turn off IBGNEND signal by executing mpNoticeIBGNRecordRefEnd() in the MotoPlus application before IBGNSTART instruction is executed.
Description:
The setting of the playback file is not completed at the time of IBGNSTART PLAYBACK=ON instruction executed.
Remedy:
Complete the setting of the playback file by executing mpNoticeIBGNPlaybackSetEnd() in the MotoPlus application before IBGNSTART PLAYBACK=ON instruction is executed.
Description:
Job name in the playback file is wrong at the time of IBGNSTART PLAYBACK=ON instruction executed.
Remedy:
Set the job name in which IBGNSTART PLAYBACK=ON instruction is executed in the playback file.
Description:
The setting of interpolation clock in the playback file is wrong at the time of IBGNSTART PLAYBACK=ON instruction executed.
Remedy:
Set the interpolation clock acquired in the record file in the playback file.
Description:
The start/end step number in the playback file is wrong at the time of IBGNSTART PLAYBACK=ON instruction executed.
Remedy:
Set the start/end step number of the job in which the record file was made in the playback file.
Description:
IBGNSTART PLAYBACK=ON instruction was executed in a forward direction, before a robot arrives at the start step of the playback file in a backward direction.
Remedy:
Execute IBGNSTART PLAYBACK=ON instruction in a forward direction, after a robot arrives at the start step of the playback file in a backward direction, when IBGNSTART PLAYBACK=ON instruction was executed in a backward direction.
Description:
An error occurred when IBGNSTART PLAYBACK=ON instruction was executed in a backward direction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Brake slip detection was commanded to be executed while another optional function was in execution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If another optional function was commanded to be executed, cannot execute brake slip detection. Correct the job.
Description:
Brake slip detection could not be executed in the specified axis.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Holding torque data which is calculated by the brake slip detection is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Detection torque data which is calculated by the brake slip detection is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The torque value for the brake slip detection device is not set.
Remedy:
(1) Reset the alarm.
(2) Check the check torque value settings.
Description:
Holding torque data which is calculated by the brake slip detection exceeds the limit.
Remedy:
(1) Reset the alarm.
(2) Check the check torque value settings.
Description:
The parameter of the pulse operation exceeds the limit.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
The parameter of the error detection value parameter is incorrect.
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
An attempt was made to pass the B-axis zero degree position (singular area).
Remedy:
Check the teaching position of the job so that the manipulator does not pass the B-axis zero degree position (singular area).
Description:
The setting of the form data for Flip/No Flip is not “B-axis Angle.
Remedy:
Set “1” to “S2C658: Type data detail settings”.
Description:
Learning control table setting error.
Remedy:
(1) Reset the alarm, and then try again.
(2) If another optional function was commanded to be executed, cannot execute brake slip detection. Correct the job.
Description:
Learning control table ID is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Multiple task execution error
Remedy:
The Learning control cannot execute the same time by multiple tasks.
Correct the job.
Description:
Setting of “START” in the user group I/O setting file is 0.
Remedy:
Set a value of 1-4096 at “START” in the user group I/O setting file.
Description:
Setting of “LENGTH” in the user group I/O setting file is abnormal.
Remedy:
Set a value of 1-32 at “LENGTH” in the user group I/O setting file.
Description:
The number of I/O signals in the definition of the user group I/O is out of a range.
Remedy:
Set “START” or “LENGTH” in the user group I/O setting file, so that the number of I/O signals in the definition of the user group I/O is within a range.
Description:
A number of the user group I/O is abnormal.
Remedy:
Set a number of the user group I/O to 1-64 used in the JOB.
Description:
Sub Code: Control group
Remedy:
Check the following settings.
(2) Check the following setting in case of the robot with the special range of motion.
Description:
Sub Code: Control group
Remedy:
Check the following settings.
(2) Check the following setting in case of the robot with the special range of motion.
Description:
Setting of “START” in the user analog I/O setting file is 0.
Remedy:
Set a value of 1-4096 at “START” in the user analog I/O setting file.
Description:
The number of I/O signals in the definition of the user analog I/O is out of a range.
Remedy:
Set “START” or “LENGTH” in the user analog I/O setting file, so that the number of I/O signals in the definition of the user analog I/O is within a range.
Description:
The number of the user analog I/O setting file is abnormal.
Remedy:
Set the number of the user analog I/O setting file to 1-16 used in the JOB.
Description:
Overrun limit switch control group that is displayed in the sub code has tripped.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, overrun limit switch is released. Select “OVERRUN&SHOCK SENSOR” under sub menu “ROBOT” to reset the limit switch.
Description:
Emergency stop signal of programming pendant was unmatched longer than a certain time.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Emergency stop signal of the panel box was unmatched for a certain time.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
External emergency stop signal was unmatched for a certain time.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The enable switch signal of Programming Pendant was unmatched for a certain time.
Remedy:
(1) Reset the alarm.
(2) There are two contact points for an enable switch, and only one point may be turned on by how to squeeze it or when putting it on the place where it is not a plane such as on the knee etc.
Check how to squeeze or put the programming pendant on flat.
Description:
External Enable signal was unmatched for a certain time.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board. In a system where a plurality of ASF01 boards are connected, replace the board, which is connected to the ON_ENABLE signal on which the alarm occurred.
Description:
Safety fence signal is unmatched for a certain time.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The meaning of each sub code is as follows:
1:OT1
2:OT2
3:OT3
4:OT4
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, overrun limit switch is released. Select “OVERRUN&SHOCK SENSOR” under sub menu “ROBOT” to reset the limit switch.
Description:
The meaning of each sub code is as follows:
1:ON_ENABLE1
2:ON_ENABLE2
3:ON_ENABLE3
4:ON_ENABLE4
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Full speed test signal was unmatched for a certain time.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board.
Description:
The meaning of each sub code is as follows:
1:GSIN1
2:GSIN2
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The meaning of each sub code is as follows:
D01:XIN01
D02:XIN02
D03:XIN03
D04:XIN04
D05:XIN05
D06:XIN06
D07:XIN07
D08:XIN08
D09:XIN09
D10:XIN10
D11:XIN11
D12:XIN12
D13:XIN13
D14:XIN14
D15:XIN15
D16:XIN16
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Sub code indicates the process that the software of CPU1 or CPU2 detected an error.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board.
In a system where a plurality of ASF01 boards are connected, replace the ASF01 board which is connected to the first SDCA01 board.
Description:
Sub code indicates the process that the software of CPU1 or CPU2 detected an error.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board.
In a system where a plurality of ASF01 boards are connected, replace the ASF01 board which is connected to the first SDCA01 board.
Description:
Sub code indicates the process that the software of CPU1 or CPU2 detected an error.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board.
In a system where a plurality of ASF01 boards are connected, replace the ASF01 board which is connected to the first SDCA01 board.
Description:
Sub code indicates the process that the software of CPU1 or CPU2 detected an error.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board.
In a system where a plurality of ASF01 boards are connected, replace the ASF01 board which is connected to the first SDCA01 board.
Description:
Sub code indicates the process that the software of CPU1 or CPU2 detected an error.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board.
In a system where a plurality of ASF01 boards are connected, replace the ASF01 board which is connected to the first SDCA01 board.
Description:
Sub code indicates the process that the software of CPU1 or CPU2 detected an error.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board.
In a system where a plurality of ASF01 boards are connected, replace the ASF01 board which is connected to the first SDCA01 board.
Description:
An error is detected by ASF01 board.
The error is occurred in the signal that is inverted representation.
CPU1 1:OT1
CPU1 2:OT2
CPU1 3:OT3
CPU1 4:OT4
CPU2 1:OT1 CPU2 2:OT2 CPU2 3:OT3 CPU2 4:OT4
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board.
In a system where a plurality of ASF01 boards are connected, replace the board, which is connected to the overrun signal on which the alarm occurred.
Description:
An error is detected by ASF01 board.
The meaning of each sub code is as follows:
CPU1 1:ON_ENABLE1
CPU1 2:ON_ENABLE2
CPU1 3:ON_ENABLE3
CPU1 4:ON_ENABLE4
CPU2 1:ON_ENABLE1 CPU2 2:ON_ENABLE2 CPU2 3:ON_ENABLE3 CPU2 4:ON_ENABLE4
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board.
In a system where a plurality of ASF01 boards are connected, replace the board, which is connected to the ON_ENABLE signal on which the alarm occurred.
Description:
Sub code indicates the process that the software of CPU1 or CPU2 detected an error.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board.
In a system where a plurality of ASF01 boards are connected, replace the board, which is connected to the ON_ENABLE signal on which the alarm occurred.
Description:
The meaning of each sub code is as follows:
CPU1 1:GSIN1
CPU1 2:GSIN2
CPU2 1:GSIN1 CPU2 2:GSIN2
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The meaning of each sub code is as follows:
D01:XIN01
D02:XIN02
D03:XIN03
D04:XIN04
D05:XIN05
D06:XIN06
D07:XIN07
D08:XIN08
D09:XIN09
D10:XIN10
D11:XIN11
D12:XIN12
D13:XIN13
D14:XIN14
D15:XIN15
D16:XIN16
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The meaning of each sub code is as follows:
1:KMMB1
2:KMMB2
3:KMMB3
4:KMMB4
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The meaning of each sub code is as follows:
CPU1 1:EDM1
CPU1 2:EDM2
CPU1 3:EDM3
CPU1 4:EDM4
CPU2 1:EDM1 CPU2 2:EDM2 CPU2 3:EDM3 CPU2 4:EDM4
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Content:
An feedback error of the output of brake signal is detected by ASF01 board in diagnosis process.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board.
In a system where a plurality of ASF01 boards are connected, replace the board on which the alarm occurred.
Content:
An feedback error of the output of contactor control signal is detected by ASF01 board in diagnosis process.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The meaning of each sub code is as follows:
CPU1 1:GSEDM1
CPU1 2:GSEDM2
CPU2 1:GSEDM1 CPU2 2:GSEDM2
Remedy:
This alarm can occur after the software update.
If feedback signals of GSOUTs are not necessary in the system, change settings about ‘GSOUT Feedback SETTING’ in SAFETY LOGICAL CIRCUIT SETTING on maintenance mode.
Description:
The meaning of each sub code is as follows:
D01:XOUT01
D02:XOUT02
D03:XOUT03
D04:XOUT04
D05:XOUT05
D06:XOUT06
D07:XOUT07
D08:XOUT08
D09:XOUT09
D10:XOUT10
D11:XOUT11
D12:XOUT12
D13:XOUT13
D14:XOUT14
D15:XOUT15
D16:XOUT16
Remedy:
This alarm can occur after the software update.
If feedback signals of FSBOUTs(XOUTs) are not necessary in the system, change settings about ‘XOUT Feedback SETTING’ in SAFETY LOGICAL CIRCUIT SETTING on maintenance mode.
Description:
The meaning of each sub code is as follows:
CPU1 1:SFRON1
CPU1 2:SFRON2
CPU1 3:SFRON3
CPU1 4:SFRON4
CPU2 1:SFRON1 CPU2 2:SFRON2 CPU2 3:SFRON3 CPU2 4:SFRON4
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The meaning of each sub code is as follows:
CPU1 1:STO1
CPU1 2:STO2
CPU1 3:STO3
CPU1 4:STO4
CPU2 1:STO1 CPU2 2:STO2 CPU2 3:STO3 CPU2 4:STO4
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board.
In a system where a plurality of ASF01 boards are connected, replace the board, which is connected to the signal on which the alarm occurred.
Description:
The meaning of each sub code is as follows:
CPU1 1:GSOUT1
CPU1 2:GSOUT2
CPU2 1:GSOUT1 CPU2 2:GSOUT2
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The meaning of each sub code is as follows:
D01:XOUT01
D02:XOUT02
D03:XOUT03
D04:XOUT04
D05:XOUT05
D06:XOUT06
D07:XOUT07
D08:XOUT08
D09:XOUT09
D10:XOUT10
D11:XOUT11
D12:XOUT12
D13:XOUT13
D14:XOUT14
D15:XOUT15
D16:XOUT16
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The meaning of each sub code is as follows:
1:KMMB1
2:KMMB2
3:KMMB3
4:KMMB4
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Sub-code indicates the circuit number that detected the error.
Remedy:
Please display the screen of the “safety function” - “safety logical circuit”, and check the value of a “signal”, “logic”, and a “timer.”
When a value is inaccurate, please set up the right value and perform “writing.”
Description:
Safe logic circuit information transmission error was detected.
Remedy:
Please display the screen of the “safety function” - “safe logic circuit”, and check the value of a “signal”, “logic”, and a “timer.”
When a value is inaccurate, please set up the right value and perform “writing.”
Description:
Timer delay information transmission error was detected.
Remedy:
Please display the screen of the “safety function” - “safe logic circuit”, and check the value of a “signal”, “logic”, and a “timer.”
When a value is inaccurate, please set up the right value and perform “writing.”
Description:
M-safety signal alloc information transmission error was detected.
Remedy:
Please display the screen of the “safety function” - “safe logic circuit”, and check the value of a “signal”, “logic”, and a “timer.”
When a value is inaccurate, please set up the right value and perform “writing.”
Description:
Safety signal board alloc information transmission error was detected.
Remedy:
Please display the screen of the “safety function” - “safe logic circuit”, and check the value of a “signal”, “logic”, and a “timer.”
When a value is inaccurate, please set up the right value and perform “writing.”
Description:
M-safety command reception time out was detected.
Remedy:
Please display the screen of the “safety function” - “safe logic circuit”, and check the value of a “signal”, “logic”, and a “timer.”
When a value is inaccurate, please set up the right value and perform “writing.”
Description:
Safe logic circuit information write error was detected.
Remedy:
Please display the screen of the “safety function” - “safe logic circuit”, and check the value of a “signal”, “logic”, and a “timer.”
When a value is inaccurate, please set up the right value and perform “writing.”
Description:
Safe logic circuit information cancel error was detected.
Remedy:
Please display the screen of the “safety function” - “safe logic circuit”, and check the value of a “signal”, “logic”, and a “timer.”
When a value is inaccurate, please set up the right value and perform “writing.”
Content:
ASF01 board detected an error of the 24V power supply for SERVO I/O( DIRECTIN ) signals.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors. Check the insertion, connection, Short circuit , ground or 24V power line (DIRECTIN signals) fault of the followings.
Description:
When P-PLC instruction was executed, there was not PLCSTPON instruction or PLCSTPOF instruction.
Remedy:
(1) Reset the alarm.
(2) Check whether PLCSTPON instruction and PLCSTPOF instruction is registered. When unregistered, register PLCSTPON instruction and PLCSTPOF instruction.
Description:
PLCSTPON instruction or PLCSTPOF instruction is duplicated in the PointPLC program.
Remedy:
(1) Reset the alarm.
(2) delete duplicate PLCSTPON instruction or PLCSTPOF instruction
Description:
An attempt was made to execute an instruction that could not be executed in the PointPLC program.
Remedy:
(1) Reset the alarm.
(2) delete the instruction which cannot be executed in the PointPLC program.
Description:
PointPLC Program could not be executed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PointPLC Program could not be executed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PointPLC Program execution result is err.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PointPLC Program execution result is err.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PointPLC Program execution result is err.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PointPLC function is invalid.
Remedy:
Enable PointPLC function.
Description:
Sub Code: Signifies the file number, control group and axis in which the alarm occurred.
Remedy:
Check the following settings.
Description:
Sub Code: Signifies the file number, control group and axis in which the alarm occurred.
Remedy:
Check the following settings.
Description:
Sub Code: Signifies the file number, control group, axis and error type in which the alarm occurred.
Remedy:
Check the following settings.
Description:
Sub Code: Signifies the file number, control group and axis in which the alarm occurred.
Remedy:
Check the following settings.
Description:
Sub Code: Signifies the file number, control group and axis in which the alarm occurred.
Remedy:
Check the following settings.
Description:
Sub Code: Signifies the file number, control group and error type in which the alarm occurred.
Remedy:
Check the speed limit condition file that is indicated in the sub code is set correctly.
Description:
Sub Code: Signifies the control group and error type in which the alarm occurred.
Remedy:
Check the speed limit condition file that is indicated in the sub code is set correctly.
Description:
Sub Code: Signifies the file number and control group in which the alarm occurred.
Remedy:
Check the speed limit condition file that is indicated in the sub code is set correctly.
Description:
Sub Code: Signifies the file number, control group and axis in which the alarm occurred.
Remedy:
Check the speed limit condition file that is indicated in the sub code is set correctly.
Description:
Sub Code: Signifies the file number, control group and error type in which the alarm occurred.
Error type means: 1:All tool change monitoring condition files is invalid. 2:It detects a mismatch of monitoring tool number and the selection tool file number. 3:Multiple tool change monitoring condition files is enabled. 4:Monitoring tool model(tool interference file) is not set.
Remedy:
Check the following settings.
Description:
Sub Code: Signifies the file number and control group in which the alarm occurred.
Remedy:
Check the following settings.
Description:
Sub Code: Signifies the file number, control group and axis in which the alarm occurred.
Remedy:
Check the following settings.
Description:
Sub Code: Signifies the file number and control group in which the alarm occurred.
Remedy:
Check the following settings.
Description:
Sub Code:
Code [X _ _ _ ] indicates the abnormal content.
1000:Input/output signal number in condition file is abnormal.
2000:General safety input signal that is not available is set in condition file.
3000:General safety output signal that is not available is set in condition file.
4000:Safety fieldbus input signal that is not available is set in condition file.
5000:Safety fieldbus output signal that is not available is set in condition file.
6000:File valid condition data is abnormal.
Code [ _ Y _ _ ] indicates the type of condition file abnormality occurs. 100:Axis range limit function 200:Axis speed monitor function 300:Speed limit function 400:Robot range limit function 500:Tool angle monitor function 600:Tool change monitor function
Code [ _ _ Z Z] indicates the number of condition file abnormality occurs.
Remedy:
(1) Check the configuration of condition file abnormality occurs.
(2) Reset the alarm, and then try again.
Content:
Execution time of the safety monitoring process has exceeded the specified value.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, reduce the number of robot range limit condition files validated at the same time.
Content:
Can not change the play mode, when function disable mode is ON in temporary,
Remedy:
(1) Change the teach mode.
(2) Reset the alarm, and then try again.
Description:
Sub Code: Signifies the file kind in which the alarm occurred.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which it is going to load is surely saved as data of functional safety.
Content:
The ASF01 board has detected a range combine function.
Remedy:
Reset the alarm, and then try again.
Description:
Sub Code:
Code [X _ _ _ ] indicates the abnormal content.
1000:Input/output signal number in condition file is abnormal.
4000:Safety fieldbus input signal that is not available is set in condition file.
5000:Safety fieldbus output signal that is not available is set in condition file.
6000:File valid condition data is abnormal.
Code [ _ Y _ _ ] indicates the type of condition file abnormality occurs. 100:Axis range limit function 200:Axis speed monitor function 300:Speed limit function 400:Robot range limit function 500:Tool angle monitor function 600:Tool change monitor function
Code [ _ _ Z Z] indicates the number of condition file abnormality occurs.
Remedy:
(1) Check the configuration of condition file abnormality occurs.
(2) Reset the alarm, and then try again.
Description:
Sub Code:
Code [X _ _ _ ] indicates the abnormal content.
1000:Input/output signal number in condition file is abnormal.
4000:Safety logical circuit input signal that is not available is set in condition file.
5000:Safety logical circuit output signal that is not available is set in condition file.
6000:File valid condition data is abnormal.
Code [ _ Y _ _ ] indicates the type of condition file abnormality occurs. 100:Axis range limit function 200:Axis speed monitor function 300:Speed limit function 400:Robot range limit function 500:Tool angle monitor function 600:Tool change monitor function
Code [ _ _ Z Z] indicates the number of condition file abnormality occurs.
Remedy:
(1) Check the configuration of condition file abnormality occurs.
(2) Reset the alarm, and then try again.
Description:
Sub Code: Signifies the physical No. of converter in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Content:
An error of the feedback signal is detected by ASF01 board in feedback diagnosis.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board. Save the CMOS.BIN before replacing the board to be safe.
Description:
Sub Code: Signifies the control axis number which detected an error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the ASF01-CN205 connectors.
Description:
Sub Code: Signifies the control axis number which detected an error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the ASF01-CN205 connectors.
Description:
Sub Code: Signifies the control axis number which detected an error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the ASF01-CN205 connectors.
Description:
Sub Code: Signifies the control axis number which detected an error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Sub Code: Signifies the control axis number which detected an error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the APU01 unit. Save the CMOS.BIN before replacing the unit to be safe.
Description:
Sub Code: Signifies the control axis number which detected an error
Remedy:
Turn ON the servo power for the servo dresser axis to be operated.
Description:
Sub Code: Signifies the control axis number which detected an error
Remedy:
Check if metal pieces getting into dresser blades prevent the dresser from rotating.
Content:
An error occurred in MotoLogix.
Remedy:
(1) Reset the alarm and execute again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Failed in Move command.
Undefined Move command has been set.
Remedy:
Input correct data.
Description:
Failed in Move command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in Move command.
Move command is received while multi move motion after MultiMoveOff.
Remedy:
(1) Reset the alarm.
(2) Send move command after multi move motion completed.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
Undefined speed unit has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
Undefined rotational speed has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
The VMAX speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
The VMAX and search can not be specified to the same target.
Remedy:
(1) Reset the alarm
(2) Specify other than 2 to speedUnits or, Reset search by executing ResetSearch command.
(3) Then try again.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
The VMAX and multi move cannot be used.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group1)
Multi move with searching is not allowed.
Remedy:
(1) Reset the alarm
(2) Execute ResetSearch and MultiMoveOff command.
(3) Execute either SetSearch or MultiMoveOn command.
(4) Execute MoveLinearAbsolute command.
Description:
Failed in MoveLinearRelative command. (Control group1)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
Undefined speed unit has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
Undefined rotational speed has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
The VMAX speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveLinearRelative command. (Control group1)
The VMAX and search can not be specified to the same target.
Remedy:
(1) Reset the alarm
(2) Specify other than 2 to speedUnits or, Reset search by executing ResetSearch command.
(3) Then try again.
Description:
Failed in MoveLinearRelative command. (Control group1)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveLinearRelative command. (Control group1)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
The VMAX and multi move cannot be used.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group1)
Multi move with searching is not allowed.
Remedy:
(1) Reset the alarm
(2) Execute ResetSearch and MultiMoveOff command.
(3) Execute either SetSearch or MultiMoveOn command.
(4) Execute MoveLinearRelative command.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
Search is not available for axis motion.
Remedy:
Search can be used linear motion.
(1) Reset the alarm.
(2) Execute linear move command.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group1)
Multi move motion is not available for axis motion.
Remedy:
(1) Reset the alarm
(2) Use linear move command.
Description:
Failed in MoveAxisRelative command. (Control group1)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group1)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group1)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group1)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group1)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group1)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group1)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group1)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group1)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group1)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group1)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group1)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveAxisRelative command. (Control group1)
Search is not available for axis motion.
Remedy:
Search can be used linear motion.
(1) Reset the alarm.
(2) Execute linear move command.
Description:
Failed in MoveAxisRelative command. (Control group1)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveAxisRelative command. (Control group1)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group1)
Multi move motion is not available for axis motion.
Remedy:
(1) Reset the alarm.
(2) Execute linear move command.
Description:
Failed in Jog command.
Incorrect command index has been set.
Remedy:
Input correct data.
Description:
Failed in Jog command.
Undefined Jog command has been set.
Remedy:
Input correct data.
Description:
Failed in JogAxes command. (Control group1)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogAxes command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in JogAxes command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in JogTcp command. (Control group1)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogTcp command. (Control group1)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in JogTcp command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in JogTcp command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in JogAxesToPoint command. (Control group1)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogAxesToPoint command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in JogAxesToPoint command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in JogTcpToPoint command. (Control group1)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogTcpToPoint command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in JogTcpToPoint command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
Undefined coordinate system has been set.
Remedy:
(1) Reset the alarm
(2) Set correct coordinate system and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
The speed is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct speed and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
Undefined speed unit has been set.
Remedy:
(1) Reset the alarm
(2) Set correct speed unit and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
The blend factor is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct blend factor and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
Undefined blend type has been set.
Remedy:
(1) Reset the alarm
(2) Set correct blend type and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
Incorrect number of user coordinate has been set.
Remedy:
(1) Reset the alarm
(2) Set correctuser coordinate and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
Incorrect value of frame shift has been set.
Remedy:
(1) Reset the alarm
(2) Set correct value of frame shift and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
Remedy:
Reset the alarm and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
Incorrect parameter of +DOUT has been set.
Remedy:
(1) Reset the alarm
(2) Set correct +DOUT and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
The acceleration is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct acceleration and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
The deceleration is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct deceleration and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
Failed in search motion.
Remedy:
(1) Reset the alarm
(2) Reset search and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
Search function is not available for this command.
Remedy:
(1) Reset the alarm
(2) Reset search and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
Failed in multi move motion.
Remedy:
Reset the alarm and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
Incorrect control group is specified for multi move motion.
Remedy:
(1) Reset the alarm
(2) Set robot axis and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group1)
Multi move with searching is not allowed.
Remedy:
(1) Reset the alarm
(2) Reset mutli move and then execute command again.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
Undefined speed unit has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
Undefined rotational speed has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
The VMAX speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
The VMAX and search can not be specified to the same target.
Remedy:
(1) Reset the alarm
(2) Specify other than 2 to speedUnits or, Reset search by executing ResetSearch command.
(3) Then try again.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
The VMAX and multi move cannot be used.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group2)
Multi move with searching is not allowed.
Remedy:
(1) Reset the alarm
(2) Execute ResetSearch and MultiMoveOff command.
(3) Execute either SetSearch or MultiMoveOn command.
(4) Execute MoveLinearAbsolute command.
Description:
Failed in MoveLinearRelative command. (Control group2)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
Undefined speed unit has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
Undefined rotational speed has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
The VMAX speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveLinearRelative command. (Control group2)
The VMAX and search can not be specified to the same target.
Remedy:
(1) Reset the alarm
(2) Specify other than 2 to speedUnits or, Reset search by executing ResetSearch command.
(3) Then try again.
Description:
Failed in MoveLinearRelative command. (Control group2)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveLinearRelative command. (Control group2)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
The VMAX and multi move cannot be used.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group2)
Multi move with searching is not allowed.
Remedy:
(1) Reset the alarm
(2) Execute ResetSearch and MultiMoveOff command.
(3) Execute either SetSearch or MultiMoveOn command.
(4) Execute MoveLinearRelative command.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
Search is not available for axis motion.
Remedy:
Search can be used linear motion.
(1) Reset the alarm.
(2) Execute linear move command.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group2)
Multi move motion is not available for axis motion.
Remedy:
(1) Reset the alarm
(2) Use linear move command.
Description:
Failed in MoveAxisRelative command. (Control group2)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group2)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group2)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group2)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group2)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group2)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group2)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group2)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group2)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group2)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group2)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group2)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveAxisRelative command. (Control group2)
Search is not available for axis motion.
Remedy:
Search can be used linear motion.
(1) Reset the alarm.
(2) Execute linear move command.
Description:
Failed in MoveAxisRelative command. (Control group2)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveAxisRelative command. (Control group2)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group2)
Multi move motion is not available for axis motion.
Remedy:
(1) Reset the alarm.
(2) Execute linear move command.
Description:
Failed in JogAxes command. (Control group2)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogAxes command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in JogTcp command. (Control group2)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogTcp command. (Control group2)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in JogTcp command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in JogAxesToPoint command. (Control group2)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogAxesToPoint command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in JogTcpToPoint command. (Control group2)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogTcpToPoint command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
Undefined coordinate system has been set.
Remedy:
(1) Reset the alarm
(2) Set correct coordinate system and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
The speed is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct speed and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
Undefined speed unit has been set.
Remedy:
(1) Reset the alarm
(2) Set correct speed unit and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
The blend factor is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct blend factor and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
Undefined blend type has been set.
Remedy:
(1) Reset the alarm
(2) Set correct blend type and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
Incorrect number of user coordinate has been set.
Remedy:
(1) Reset the alarm
(2) Set correctuser coordinate and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
Incorrect value of frame shift has been set.
Remedy:
(1) Reset the alarm
(2) Set correct value of frame shift and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
Remedy:
Reset the alarm and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
Incorrect parameter of +DOUT has been set.
Remedy:
(1) Reset the alarm
(2) Set correct +DOUT and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
The acceleration is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct acceleration and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
The deceleration is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct deceleration and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
Failed in search motion.
Remedy:
(1) Reset the alarm
(2) Reset search and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
Search function is not available for this command.
Remedy:
(1) Reset the alarm
(2) Reset search and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
Failed in multi move motion.
Remedy:
Reset the alarm and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
Incorrect control group is specified for multi move motion.
Remedy:
(1) Reset the alarm
(2) Set robot axis and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group2)
Multi move with searching is not allowed.
Remedy:
(1) Reset the alarm
(2) Reset mutli move and then execute command again.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
Undefined speed unit has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
Undefined rotational speed has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
The VMAX speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
The VMAX and search can not be specified to the same target.
Remedy:
(1) Reset the alarm
(2) Specify other than 2 to speedUnits or, Reset search by executing ResetSearch command.
(3) Then try again.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
The VMAX and multi move cannot be used.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group3)
Multi move with searching is not allowed.
Remedy:
(1) Reset the alarm
(2) Execute ResetSearch and MultiMoveOff command.
(3) Execute either SetSearch or MultiMoveOn command.
(4) Execute MoveLinearAbsolute command.
Description:
Failed in MoveLinearRelative command. (Control group3)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
Undefined speed unit has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
Undefined rotational speed has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
The VMAX speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveLinearRelative command. (Control group3)
The VMAX and search can not be specified to the same target.
Remedy:
(1) Reset the alarm
(2) Specify other than 2 to speedUnits or, Reset search by executing ResetSearch command.
(3) Then try again.
Description:
Failed in MoveLinearRelative command. (Control group3)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveLinearRelative command. (Control group3)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
The VMAX and multi move cannot be used.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group3)
Multi move with searching is not allowed.
Remedy:
(1) Reset the alarm
(2) Execute ResetSearch and MultiMoveOff command.
(3) Execute either SetSearch or MultiMoveOn command.
(4) Execute MoveLinearRelative command.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
Search is not available for axis motion.
Remedy:
Search can be used linear motion.
(1) Reset the alarm.
(2) Execute linear move command.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group3)
Multi move motion is not available for axis motion.
Remedy:
(1) Reset the alarm
(2) Use linear move command.
Description:
Failed in MoveAxisRelative command. (Control group3)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group3)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group3)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group3)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group3)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group3)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group3)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group3)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group3)
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group3)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group3)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group3)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group3)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveAxisRelative command. (Control group3)
Search is not available for axis motion.
Remedy:
Search can be used linear motion.
(1) Reset the alarm.
(2) Execute linear move command.
Description:
Failed in MoveAxisRelative command. (Control group3)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveAxisRelative command. (Control group3)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group3)
Multi move motion is not available for axis motion.
Remedy:
(1) Reset the alarm.
(2) Execute linear move command.
Description:
Failed in JogAxes command. (Control group3)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogAxes command. (Control group3)
Remedy:
Input correct data.
Description:
Failed in JogTcp command. (Control group3)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogTcp command. (Control group3)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in JogTcp command. (Control group3)
Remedy:
Input correct data.
Description:
Failed in JogAxesToPoint command. (Control group3)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogAxesToPoint command. (Control group3)
Remedy:
Input correct data.
Description:
Failed in JogTcpToPoint command. (Control group3)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogTcpToPoint command. (Control group3)
Remedy:
Input correct data.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
Undefined coordinate system has been set.
Remedy:
(1) Reset the alarm
(2) Set correct coordinate system and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
The speed is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct speed and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
Undefined speed unit has been set.
Remedy:
(1) Reset the alarm
(2) Set correct speed unit and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
The blend factor is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct blend factor and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
Undefined blend type has been set.
Remedy:
(1) Reset the alarm
(2) Set correct blend type and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
Incorrect number of user coordinate has been set.
Remedy:
(1) Reset the alarm
(2) Set correctuser coordinate and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
Incorrect value of frame shift has been set.
Remedy:
(1) Reset the alarm
(2) Set correct value of frame shift and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
Remedy:
Reset the alarm and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
Incorrect parameter of +DOUT has been set.
Remedy:
(1) Reset the alarm
(2) Set correct +DOUT and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
The acceleration is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct acceleration and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
The deceleration is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct deceleration and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
Failed in search motion.
Remedy:
(1) Reset the alarm
(2) Reset search and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
Search function is not available for this command.
Remedy:
(1) Reset the alarm
(2) Reset search and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
Failed in multi move motion.
Remedy:
Reset the alarm and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
Incorrect control group is specified for multi move motion.
Remedy:
(1) Reset the alarm
(2) Set robot axis and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group3)
Multi move with searching is not allowed.
Remedy:
(1) Reset the alarm
(2) Reset mutli move and then execute command again.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
Undefined speed unit has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
Undefined rotational speed has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
The VMAX speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
The VMAX and search can not be specified to the same target.
Remedy:
(1) Reset the alarm
(2) Specify other than 2 to speedUnits or, Reset search by executing ResetSearch command.
(3) Then try again.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
The VMAX and multi move cannot be used.
Remedy:
Input correct data.
Description:
Failed in MoveLinearAbsolute command. (Control group4)
Multi move with searching is not allowed.
Remedy:
(1) Reset the alarm
(2) Execute ResetSearch and MultiMoveOff command.
(3) Execute either SetSearch or MultiMoveOn command.
(4) Execute MoveLinearAbsolute command.
Description:
Failed in MoveLinearRelative command. (Control group4)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
Undefined speed unit has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
Undefined rotational speed has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
The VMAX speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveLinearRelative command. (Control group4)
The VMAX and search can not be specified to the same target.
Remedy:
(1) Reset the alarm
(2) Specify other than 2 to speedUnits or, Reset search by executing ResetSearch command.
(3) Then try again.
Description:
Failed in MoveLinearRelative command. (Control group4)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveLinearRelative command. (Control group4)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
The VMAX and multi move cannot be used.
Remedy:
Input correct data.
Description:
Failed in MoveLinearRelative command. (Control group4)
Multi move with searching is not allowed.
Remedy:
(1) Reset the alarm
(2) Execute ResetSearch and MultiMoveOff command.
(3) Execute either SetSearch or MultiMoveOn command.
(4) Execute MoveLinearRelative command.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
Search is not available for axis motion.
Remedy:
Search can be used linear motion.
(1) Reset the alarm.
(2) Execute linear move command.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveAxisAbsolute command. (Control group4)
Multi move motion is not available for axis motion.
Remedy:
(1) Reset the alarm
(2) Use linear move command.
Description:
Failed in MoveAxisRelative command. (Control group4)
Undefined target position type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group4)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group4)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group4)
The blend factor is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group4)
Undefined blend type has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group4)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group4)
Incorrect number of position variable has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group4)
Incorrect value of frame shift has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group4)
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group4)
Incorrect parameter of +DOUT has been set.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group4)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group4)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group4)
Failed in search motion.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in MoveAxisRelative command. (Control group4)
Search is not available for axis motion.
Remedy:
Search can be used linear motion.
(1) Reset the alarm.
(2) Execute linear move command.
Description:
Failed in MoveAxisRelative command. (Control group4)
Failed in multi move motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in MoveAxisRelative command. (Control group4)
Incorrect control group is specified for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MoveAxisRelative command. (Control group4)
Multi move motion is not available for axis motion.
Remedy:
(1) Reset the alarm.
(2) Execute linear move command.
Description:
Failed in JogAxes command. (Control group4)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogAxes command. (Control group4)
Remedy:
Input correct data.
Description:
Failed in JogTcp command. (Control group4)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogTcp command. (Control group4)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in JogTcp command. (Control group4)
Remedy:
Input correct data.
Description:
Failed in JogAxesToPoint command. (Control group4)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogAxesToPoint command. (Control group4)
Remedy:
Input correct data.
Description:
Failed in JogTcpToPoint command. (Control group4)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in JogTcpToPoint command. (Control group4)
Remedy:
Input correct data.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
Undefined coordinate system has been set.
Remedy:
(1) Reset the alarm
(2) Set correct coordinate system and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
The speed is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct speed and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
Undefined speed unit has been set.
Remedy:
(1) Reset the alarm
(2) Set correct speed unit and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
The blend factor is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct blend factor and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
Undefined blend type has been set.
Remedy:
(1) Reset the alarm
(2) Set correct blend type and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
Incorrect number of user coordinate has been set.
Remedy:
(1) Reset the alarm
(2) Set correctuser coordinate and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
Incorrect value of frame shift has been set.
Remedy:
(1) Reset the alarm
(2) Set correct value of frame shift and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
Remedy:
Reset the alarm and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
Incorrect parameter of +DOUT has been set.
Remedy:
(1) Reset the alarm
(2) Set correct +DOUT and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
The acceleration is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct acceleration and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
The deceleration is out of range.
Remedy:
(1) Reset the alarm
(2) Set correct deceleration and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
Failed in search motion.
Remedy:
(1) Reset the alarm
(2) Reset search and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
Search function is not available for this command.
Remedy:
(1) Reset the alarm
(2) Reset search and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
Failed in multi move motion.
Remedy:
Reset the alarm and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
Incorrect control group is specified for multi move motion.
Remedy:
(1) Reset the alarm
(2) Set robot axis and then execute command again.
Description:
Failed in MoveCircularOutBorder command. (Control group4)
Multi move with searching is not allowed.
Remedy:
(1) Reset the alarm
(2) Reset mutli move and then execute command again.
Description:
Failed in Config command.
Incorrect command index has been set.
Remedy:
Input correct data.
Description:
Failed in Config command.
Undefined Config command has been set.
Remedy:
Input correct data.
Description:
Failed in Config command.
The size of command buffer is out of range.
Remedy:
Input correct data.
Description:
Failed in GetModuleInfo command.
Remedy:
Input correct data.
Description:
Failed in GetModuleInfo command.
The number of step is out of range.
Remedy:
Input correct data.
Description:
Failed in GetModuleInfo command.
The size of command buffer is out of range. (IP address)
Remedy:
Input correct data.
Description:
Failed in GetModuleInfo command.
The size of command buffer is out of range. (MAC address)
Remedy:
Input correct data.
Description:
Failed in GetModuleInfo command.
The size of command buffer is out of range. (Module type)
Remedy:
Input correct data.
Description:
Failed in GetModuleInfo command.
The size of command buffer is out of range. (Version)
Remedy:
Input correct data.
Description:
Failed in GetProperties command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in GetProperties command. (Control group1)
The number of step is out of range.
Remedy:
Input correct data.
Description:
Failed in GetProperties command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group1)
Invalid data of tool has been set.
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group1)
Incorrect number of tool has been set.
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group1)
Failed to write tool file.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group1)
Invalid data of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group1)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group1)
Failed to write user coordinate file.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group1)
Failed to make user coordinate.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group1)
Failed to convert user coordinate.
Remedy:
Input correct data.
Description:
Failed in SetFrameShift command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in SetFrameShift command. (Control group1)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in SetFrameShift command. (Control group1)
Failed to set frame shift.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group1)
Undefined IZ action has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group1)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group1)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group1)
Incorrect ID number has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group1)
Failed to write cube file.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group1)
Undefined IZ action has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group1)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group1)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group1)
Incorrect ID number has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group1)
Failed to write cube file.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Undefined transform type has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert Axis coordinates to TCP coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert Axis coordinates to TCP coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert TCP coordinates to Axis coordinates.
Incorrect number of tool has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert TCP coordinates to Axis coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert TCP in World frame to User frame.
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert TCP in World frame to User frame.
Failed to convert Input coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert TCP in World frame to User frame.
Failed to convert User coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert TCP in World frame to User frame.
Failed to create inverse matrix of user coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert TCP in World frame to User frame.
Failed in multiplication of coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert TCP in World frame to User frame.
Failed to convert Output coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert TCP in User frame to World frame.
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert TCP in User frame to World frame.
Failed to convert Input coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert TCP in User frame to World frame.
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert TCP in User frame to World frame.
Failed in multiplication of coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group1)
Failed to convert TCP in User frame to World frame.
Failed to convert Output coordinates.
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStart command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStart command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStart command. (Control group1)
Incorrect number of conveyor has been set.
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStart command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStop command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStop command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStop command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group1)
The size of command buffer is out of range.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group1)
Failed to read position variable file.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group1)
Failed to convert Pulse coordinates to Axis coordinates.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group1)
Failed to convert Axis coordinates to TCP coordinates.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group1)
Failed to convert TCP coordinates to Axis coordinates.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group1)
Failed to convert TCP in User frame to World frame.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group1)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group1)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command. (Control group1)
Undefined position type has been set.
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command. (Control group1)
Failed to write position variable file.
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command. (Control group1)
Failed to convert Axis coordinates to Pulse coordinates.
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in SetBasePose command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in SetBasePose command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in SetBasePose command. (Control group1)
Failed to write file.
Remedy:
Input correct data.
Description:
Failed in SetBasePose command.
You can not use this command for the robot of control group1.
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command. (Control group1)
Failed to get current position of pulse type.
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command. (Control group1)
Failed to write file.
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command. (Control group1)
Undefined offset type has been set.
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command. (Control group1)
Failed to get current position of pulse type.
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command. (Control group1)
Failed to read file.
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command. (Control group1)
Undefined offset type has been set.
Remedy:
Input correct data.
Description:
Failed in VarsGet command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in VarsGet command. (Control group1)
Undefined variable type has been set.
Remedy:
Input correct data.
Description:
Failed in VarsGet command. (Control group1)
Incorrect number of variable has been set.
Remedy:
Input correct data.
Description:
Failed in VarsGet command. (Control group1)
Incorrect number of getting has been set.
Remedy:
Input correct data.
Description:
Failed in VarsSet command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in VarsSet command. (Control group1)
Undefined variable type has been set.
Remedy:
Input correct data.
Description:
Failed in VarsSet command. (Control group1)
Incorrect number of variable has been set.
Remedy:
Input correct data.
Description:
Failed in VarsSet command. (Control group1)
Incorrect number of setting has been set.
Remedy:
Input correct data.
Description:
Failed in WriteApplicationData command.
Remedy:
Input correct data.
Description:
Failed in WriteApplicationData command.
Failed to write user frame file.
Remedy:
Input correct data.
Description:
Failed in SetProperties command. (Control group1)
Remedy:
Input correct data.
Description:
Failed in SetProperties command. (Control group1)
The number of step is out of range.
Remedy:
Input correct data.
Description:
Failed in SetProperties command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in SetProperties command. (Control group1)
The axis index is out of range.
Remedy:
Input correct data.
Description:
Failed in SetGlobalPrm command.
Remedy:
Input correct data.
Description:
Failed in SetGlobalPrm command.
Incorrect value of command type has been set.
Remedy:
Input correct data.
Description:
Failed in SetGlobalPrm command.
The speed override value is out of range.
Remedy:
Input correct data.
Description:
Failed in ToolCalib command.(Control group1)
Remedy:
Reset the alarm and execute again.
Description:
Failed in ToolCalib command.
Incorrect number of control group has been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in ToolCalib command.(Control group1)
Incorrect number of tool has been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct tool number and execute again.
Description:
Failed in ToolCalib command.(Control group1)
Incorrect number of calibration method has been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct calibration method and execute again.
Description:
Failed in ToolCalib command.(Control group1)
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in ToolCalib command.(Control group1)
The teaching points include the same points.
Remedy:
(1) Reset the alarm.
(2) Set the teaching point to a different point and execute again.
Description:
Failed in ToolCalib command.(Control group1)
An alarm or error is occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in ToolCalib command.(Control group1)
Editing is prohibited.
Remedy:
Reset the alarm and execute again.
Description:
Failed in ToolCalib command.(Control group1)
Specified group is not supported .
Remedy:
(1) Reset the alarm.
(2) Specify robot control group and execute again.
Description:
Failed in ToolCalib command.(Control group1)
The tool calibration function is running.
Remedy:
(1) Reset the alarm.
(2) Stop tool calibration and execute again.
Description:
Failed in ReleaseBrake command. (Control group1)
Remedy:
Reset the alarm and execute again.
Description:
Failed in ReleaseBrake command. (Control group1)
Failed to stop manual brake release.
Remedy:
Reset the alarm and execute again.
Description:
Failed in ReleaseBrake command.
Incorrect number of control group has been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in ReleaseBrake command. (Control group1)
Incorrect axes have been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct axes information and execute again.
Description:
Failed in ReleaseBrake command. (Control group1)
ReleaseBrake command was executed when the servo power was ON.
Remedy:
(1) Reset the alarm.
(2) Turn off the servo power and execute again.
Description:
Failed in ReleaseBrake command. (Control group1)
ReleaseBrake command was executed when in emergency stop condition.
Remedy:
(1) Reset the alarm.
(2) Releasing the emergency stop and execute again.
Description:
Failed in ReleaseBrake command. (Control group1)
ReleaseBrake command was executed when the BRK_EN signal was in the release prohibition condition.
Remedy:
(1) Reset the alarm.
(2) Set the BRK_EN signal to release permission condition and execute again.
Description:
Failed in ReleaseBrake command. (Control group1)
Specified axes are lacked.
Remedy:
(1) Reset the alarm.
(2) Check the brake group information.
(3) Specify correct axes and execute again.
Description:
Failed in ReleaseBrake command. (Control group1)
Manual release brake function is invalid.
Remedy:
(1) Reset the alarm.
(2) Enable manual release brake function and execute again.
Description:
Failed in servofloat ON.
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat ON.
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in servofloat ON.
Specified servofloat type is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
(3) If the alarm occurs again, confirm that specified servofloat type function is enabled.
Description:
Failed in servofloat ON.
Specified servofloat condition file number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
Description:
Failed in servofloat ON.
Specified group is not supported axis servofloat.
Remedy:
(1) Reset the alarm.
(2) Base axes control group is not supported. Specify robot or station axes control group and execute again.
Description:
Failed in servofloat ON.
Specified group is not supported linear servofloat.
Remedy:
(1) Reset the alarm.
(2) Base and station axes control group is not supported. Specify Robot axes control group and execute again.
Description:
Failed in servofloat ON.
Specified group is different from specified one in a servofloat condition file.
Remedy:
(1) Reset the alarm.
(2) Confirm the group number specified in a servofloat condition file.
(3) Specify that group number and execute again.
Description:
Failed in servofloat ON.
Failed in referring servofloat condition file.
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat ON.
User frame number is not active.
Remedy:
(1) Reset the alarm.
(2) Set active user frame number and execute again.
Description:
Failed in servofloat ON.
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in servofloat ON.
Alarm occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat ON.
Servo power is down.
Remedy:
(1) Reset the alarm.
(2) Turn on the servo power and execute again.
Description:
Failed in servofloat OFF.
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat OFF.
Specified control group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in servofloat OFF.
Specified control group is not supported.
Remedy:
(1) Reset the alarm.
(2) Base axes control group is not supported. Specify robot or station axes control group and execute again.
Description:
Failed in servofloat OFF.
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in servofloat OFF.
Alarm occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat OFF.
Servo power is down.
Remedy:
(1) Reset the alarm.
(2) Turn on the servo power and execute again.
Description:
Failed in writing servofloat condition file.
Remedy:
Reset the alarm and execute again.
Description:
Failed in writing servofloat condition file.
Specified control group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in writing servofloat condition file.
Specified servofloat type is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
(3) If the alarm occurs again, confirm that specified servofloat type function is enabled.
Description:
Failed in writing servofloat condition file.
Specified servofloat condition file number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat condition file number and execute again.
Description:
Failed in writing servofloat condition file.
Specified control group is not supported axis servofloat.
Remedy:
(1) Reset the alarm.
(2) Base axes control group is not supported. Specify robot or station axes control group and execute again.
Description:
Failed in writing servofloat condition file.
Specified control group is not supported linear servofloat.
Remedy:
(1) Reset the alarm.
(2) Base and station axes control group is not supported. Specify Robot axes control group and execute again.
Description:
Failed in writing servofloat condition file.
Specified coordinate frame is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct coordinate frame and execute again.
Description:
Failed in writing servofloat condition file.
Specified max/min torque is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct max/min torque and execute again.
Description:
Failed in writing servofloat condition file.
Specified max/min force is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct max/min force and execute again.
Description:
Failed in writing servofloat condition file.
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in writing servofloat condition file.
Alarm occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in writing servofloat condition file.
Edit inhibited.
Remedy:
(1) Reset the alarm.
(2) Release editlock and execute again.
Description:
Failed in reading servofloat condition file.
Remedy:
Reset the alarm and execute again.
Description:
Failed in reading servofloat condition file.
Specified control group is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in reading servofloat condition file.
Specified servofloat type is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
(3) If the alarm occurs again, confirm that specified servofloat type function is enabled.
Description:
Failed in reading servofloat condition file.
Specified servofloat condition file is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat condition file number and execute again.
Description:
Failed in reading servofloat condition file.
Specified control group is different from specified one in a servofloat condition file.
Remedy:
(1) Reset the alarm.
(2) Change control group number and execute again.
Description:
Failed in reading servofloat condition file.
Instruction buffer size is not enough to read.
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetCollisionDetectionStatus command. (Control group 1)
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetCollisionDetectionStatus command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionStatus command. (Control group 1)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionStatus command. (Control group 1)
Incorrect status has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 1)
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetCollisionDetectionLevels command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 1)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 1)
Incorrect resource type has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 1)
Incorrect number of file has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 1)
Incorrect value of levels has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 1)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 1)
Remedy:
Reset the alarm and execute again.
Description:
Failed in WriteCollisionDetectionFile command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 1)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 1)
Incorrect number of file has been set.
Remedy:
Input correct data.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 1)
Incorrect value of levels has been set.
Remedy:
Input correct data.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 1)
The function parameter has not been set.
Remedy:
Enable Teach Mode Each Axis Setting Function
Description:
Failed in WriteCollisionDetectionFile command. (Control group 1)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in GetCollisionDetectionStatus command. (Control group 1)
Remedy:
Reset the alarm and execute again.
Description:
Failed in GetCollisionDetectionStatus command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in GetCollisionDetectionStatus command. (Control group 1)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in GetCollisionDetectionTorque command. (Control group 1)
Remedy:
Reset the alarm and execute again.
Description:
Failed in GetCollisionDetectionTorque command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in GetCollisionDetectionTorque command. (Control group 1)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in ResetCollisionDetectionTorque command.
Remedy:
Reset the alarm and execute again.
Description:
Failed in WriteLimitStatus command.
Remedy:
Reset the alarm and execute again.
Description:
Failed in WriteLimitStatus command.
Specified limit type is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct limit type and execute again.
Description:
Failed in WriteLimitStatus command.
All limit have been released.
Remedy:
(1) Reset the alarm.
(2) Confirm the setting of all limit release.
Cancel the all limit release and execute again.
Description:
Failed in WriteLimitStatus command.
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in WriteLimitStatus command.
Arm interference check function is invalid.
Remedy:
(1) Reset the alarm.
(2) Check whether the arm interference check function is valid and execute again.
Description:
Failed in WriteLimitStatus command.
Self interference check function is invalid.
Remedy:
(1) Reset the alarm.
(2) Check whether the self interference check function is valid and execute again.
Description:
Failed in WriteLimitStatus command.
Cube/Axis interference check function is invalid.
Remedy:
(1) Reset the alarm.
(2) Check whether the Cube/Axis interference check function is valid and execute again.
Description:
Failed in ReadLimitStatus command.
Remedy:
Reset the alarm and execute again.
Description:
Failed in ReadLimitStatus command.
Specified limit type is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct limit type and execute again.
Description:
Failed in BrakeGroupInfoGet command. (Control group1)
Remedy:
Reset the alarm and execute again.
Description:
Failed in BrakeGroupInfoGet command.
Incorrect number of control group has been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in SetSearch command.(Control Group1)
Remedy:
(1) Confirm option function: “Search function” is enabled.
(2) Reset the alarm and then try again.
Description:
Failed in SetSearch command.(Control Group1)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in SetSearch command.(Control Group1)
Specified control group is not supported search function.
Remedy:
Search function supports only robot.
(1) Reset the alarm.
(2) Specify robot and execute again.
Description:
Failed in SetSearch command.(Control Group1)
Specified InputSignalBits is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct RIN signal and then try again. Incorrect specification is shown below.
(a) It can not be specified 0.
(b) If SearchAction is specified 0, it can not be specified multiple RIN signals.
(c) It can not be specified RIN signal which number is out of range.
Description:
Failed in SetSearch command.(Control Group1)
Specified SearchAction is invalid.
Remedy:
SearchAction can be specified only 0.
(1) Reset the alarm.
(2) Specify 0 to SearchAction and execute again.
Description:
Failed in ResetSearch command.(Control Group1)
Remedy:
(1) Confirm option function: “Search function” is enabled.
(2) Reset the alarm and then try again.
Description:
Failed in ResetSearch command.(Control Group1)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in ResetSearch command.(Control Group1)
Specified control group is not supported search function.
Remedy:
Search function supports only robot.
(1) Reset the alarm.
(2) Specify robot and execute again.
Description:
Failed in GetSearchResult command.(Control Group1)
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchResult command.(Control Group1)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in GetSearchResult command.(Control Group1)
Specified control group is not supported search function.
Remedy:
Station group can not be specified.
(1) Reset the alarm.
(2) Specify robot or base axes group number and execute again.
Description:
Failed in GetSearchResult command.(Control Group1)
Memory to store result is not enough.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchResult command.(Control Group1)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in GetSearchPosition command.(Control Group1)
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group1)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in GetSearchResult command.(Control Group1)
Specified control group is not supported search function.
Remedy:
Station group can not be specified.
(1) Reset the alarm.
(2) Specify robot or base axes group number and execute again.
Description:
Failed in GetSearchPosition command.(Control Group1)
Memory to store result is not enough.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group1)
Specified coordinate system is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify world or user coordinate system and execute again.
Description:
Failed in GetSearchPosition command.(Control Group1)
Specified detected number is out of range.
Remedy:
If using search motion with SearchAction is 0, detected number must be 0.
(1) Reset the alarm.
(2) Specify 0 to detected number and execute again.
Description:
Failed in GetSearchPosition command.(Control Group1)
RIN signal has not been detected.
Remedy:
(1) Reset the alarm.
(2) Verify detected count by executing GetSearchResult command.
(3) Execute instruction again if it’s more than 0.
Description:
Failed in GetSearchPosition command.(Control Group1)
Failed in getting detected TCP position.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group1)
Failed in getting detected TCP position in User coordinate system because, user frame had been inactive when search motion was enqueued.
Remedy:
Set active user frame number when execute linear move command with search.
Description:
Failed in GetSearchPosition command.(Control Group1)
Failed in getting detected TCP position in user coordinate system..
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group1)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in MultiMoveOn command. (Control group 1)
Remedy:
Reset the alarm and execute again.
Description:
Failed in MultiMoveOn command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 1)
Specified control group is not supported.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 1)
The system state is illegal.
Remedy:
(1) Reset the alarm
(2) Confirm the system state and execute again.
Description:
Failed in MultiMoveOn command. (Control group 1)
Multiple control group is not supported.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 1)
The VMAX is not supported for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 1)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 1)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 1)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOff command. (Control group 1)
Remedy:
Reset the alarm and execute again.
Description:
Failed in MultiMoveOff command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOff command. (Control group 1)
Specified control group is not supported.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOff command. (Control group 1)
Failed to start motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 1)
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetMultiMoveMinimumBuffer command.
Incorrect number of control group has been set.
Remedy:
Input correct data.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 1)
Specified control group is not supported.
Remedy:
Input correct data.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 1)
The minimum buffer is out of range.
Remedy:
Input correct data.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 1)
The robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop the robot and execute again.
Description:
Failed in GetSafetyCRC command.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in GetSafetyCRC command.
The size of command buffer is out of range.
Remedy:
Input correct data.
Description:
Failed in GetSafetyCRC command.
The number is out of range.
Remedy:
Input correct data.
Description:
Failed in GetSafetyCRC command.
The filetype is out of range.
Remedy:
Input correct data.
Description:
Failed in MLxGetConfigLog command.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in MLxGetConfigLog command.
The size of command buffer is out of range.
Remedy:
Input correct data.
Description:
Failed in MLxGetConfigLog command.
The number is out of range.
Remedy:
Input correct data.
Description:
Failed in MLxGetConfigLog command.
The configlogtype is out of range.
Remedy:
Input correct data.
Description:
Failed in GetProperties command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in GetProperties command. (Control group2)
The number of step is out of range.
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group2)
Invalid data of tool has been set.
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group2)
Incorrect number of tool has been set.
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group2)
Failed to write tool file.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group2)
Invalid data of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group2)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group2)
Failed to write user coordinate file.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group2)
Failed to make user coordinate.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group2)
Failed to convert user coordinate.
Remedy:
Input correct data.
Description:
Failed in SetFrameShift command. (Control group2)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in SetFrameShift command. (Control group2)
Failed to set frame shift.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group2)
Undefined IZ action has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group2)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group2)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group2)
Incorrect ID number has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group2)
Failed to write cube file.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group2)
Undefined IZ action has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group2)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group2)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group2)
Incorrect ID number has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group2)
Failed to write cube file.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Undefined transform type has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert Axis coordinates to TCP coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert Axis coordinates to TCP coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert TCP coordinates to Axis coordinates.
Incorrect number of tool has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert TCP coordinates to Axis coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert TCP in World frame to User frame.
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert TCP in World frame to User frame.
Failed to convert Input coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert TCP in World frame to User frame.
Failed to convert User coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert TCP in World frame to User frame.
Failed to create inverse matrix of user coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert TCP in World frame to User frame.
Failed in multiplication of coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert TCP in World frame to User frame.
Failed to convert Output coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert TCP in User frame to World frame.
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert TCP in User frame to World frame.
Failed to convert Input coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert TCP in User frame to World frame.
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert TCP in User frame to World frame.
Failed in multiplication of coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group2)
Failed to convert TCP in User frame to World frame.
Failed to convert Output coordinates.
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStart command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStart command. (Control group2)
Incorrect number of conveyor has been set.
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStart command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStop command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStop command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group2)
The size of command buffer is out of range.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group2)
Failed to read position variable file.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group2)
Failed to convert Pulse coordinates to Axis coordinates.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group2)
Failed to convert Axis coordinates to TCP coordinates.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group2)
Failed to convert TCP coordinates to Axis coordinates.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group2)
Failed to convert TCP in User frame to World frame.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group2)
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group2)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command. (Control group2)
Undefined position type has been set.
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command. (Control group2)
Failed to write position variable file.
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command. (Control group2)
Failed to convert Axis coordinates to Pulse coordinates.
Remedy:
Input correct data.
Description:
Failed in SetBasePose command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in SetBasePose command. (Control group2)
Failed to write file.
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command. (Control group2)
Failed to get current position of pulse type.
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command. (Control group2)
Failed to write file.
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command. (Control group2)
Undefined offset type has been set.
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command. (Control group2)
Failed to get current position of pulse type.
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command. (Control group2)
Failed to read file.
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command. (Control group2)
Undefined offset type has been set.
Remedy:
Input correct data.
Description:
Failed in VarsGet command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in VarsGet command. (Control group2)
Undefined variable type has been set.
Remedy:
Input correct data.
Description:
Failed in VarsGet command. (Control group2)
Incorrect number of variable has been set.
Remedy:
Input correct data.
Description:
Failed in VarsGet command. (Control group2)
Incorrect number of getting has been set.
Remedy:
Input correct data.
Description:
Failed in VarsSet command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in VarsSet command. (Control group2)
Undefined variable type has been set.
Remedy:
Input correct data.
Description:
Failed in VarsSet command. (Control group2)
Incorrect number of variable has been set.
Remedy:
Input correct data.
Description:
Failed in VarsSet command. (Control group2)
Incorrect number of setting has been set.
Remedy:
Input correct data.
Description:
Failed in SetProperties command. (Control group2)
Remedy:
Input correct data.
Description:
Failed in SetProperties command. (Control group2)
The number of step is out of range.
Remedy:
Input correct data.
Description:
Failed in SetProperties command. (Control group2)
The axis index is out of range.
Remedy:
Input correct data.
Description:
Failed in ToolCalib command.(Control group2)
Remedy:
Reset the alarm and execute again.
Description:
Failed in ToolCalib command.(Control group2)
Incorrect number of tool has been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct tool number and execute again.
Description:
Failed in ToolCalib command.(Control group2)
Incorrect number of calibration method has been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct calibration method and execute again.
Description:
Failed in ToolCalib command.(Control group2)
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in ToolCalib command.(Control group2)
The teaching points include the same points.
Remedy:
(1) Reset the alarm.
(2) Set the teaching point to a different point and execute again.
Description:
Failed in ToolCalib command.(Control group2)
An alarm or error is occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in ToolCalib command.(Control group2)
Editing is prohibited.
Remedy:
Reset the alarm and execute again.
Description:
Failed in ToolCalib command.(Control group2)
Specified group is not supported .
Remedy:
(1) Reset the alarm.
(2) Specify robot control group and execute again.
Description:
Failed in ToolCalib command.(Control group2)
The tool calibration function is running.
Remedy:
(1) Reset the alarm.
(2) Stop tool calibration and execute again.
Description:
Failed in ReleaseBrake command(Control group2) .
Remedy:
Reset the alarm and execute again.
Description:
Failed in ReleaseBrake command. (Control group2)
Failed to stop manual brake release.
Remedy:
Reset the alarm and execute again.
Description:
Failed in ReleaseBrake command. (Control group2)
Incorrect axes have been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct axes information and execute again.
Description:
Failed in ReleaseBrake command. (Control group2)
ReleaseBrake command was executed when the servo power was ON.
Remedy:
(1) Reset the alarm.
(2) Turn off the servo power and execute again.
Description:
Failed in ReleaseBrake command. (Control group2)
ReleaseBrake command was executed when in emergency stop condition.
Remedy:
(1) Reset the alarm.
(2) Releasing the emergency stop and execute again.
Description:
Failed in ReleaseBrake command. (Control group2)
ReleaseBrake command was executed when the BRK_EN signal was in the release prohibition condition.
Remedy:
(1) Reset the alarm.
(2) Set the BRK_EN signal to release permission condition and execute again.
Description:
Failed in ReleaseBrake command. (Control group2)
Specified axes are lacked.
Remedy:
(1) Reset the alarm.
(2) Check the brake group information.
(3) Specify correct axes and execute again.
Description:
Failed in ReleaseBrake command. (Control group2)
Manual release brake function is invalid.
Remedy:
(1) Reset the alarm.
(2) Enable manual release brake function and execute again.
Description:
Failed in servofloat ON (Control Group No.2).
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat ON (Control Group No.2).
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in servofloat ON (Control Group No.2).
Specified servofloat type is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
(3) If the alarm occurs again, confirm that specified servofloat type function is enabled.
Description:
Failed in servofloat ON (Control Group No.2).
Specified servofloat condition file number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
Description:
Failed in servofloat ON (Control Group No.2).
Specified group is not supported axis servofloat.
Remedy:
(1) Reset the alarm.
(2) Base axes control group is not supported. Specify robot or station axes control group and execute again.
Description:
Failed in servofloat ON (Control Group No.2).
Specified group is not supported linear servofloat.
Remedy:
(1) Reset the alarm.
(2) Base and station axes control group is not supported. Specify Robot axes control group and execute again.
Description:
Failed in servofloat ON (Control Group No.2).
Specified group is different from specified one in a servofloat condition file.
Remedy:
(1) Reset the alarm.
(2) Confirm the group number specified in a servofloat condition file.
(3) Specify that group number and execute again.
Description:
Failed in servofloat ON (Control Group No.2).
Failed in referring servofloat condition file.
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat ON (Control Group No.2).
User frame number is not active.
Remedy:
(1) Reset the alarm.
(2) Set active user frame number and execute again.
Description:
Failed in servofloat ON (Control Group No.2).
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in servofloat ON (Control Group No.2).
Alarm occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat ON (Control Group No.2).
Servo power is down.
Remedy:
(1) Reset the alarm.
(2) Turn on the servo power and execute again.
Description:
Failed in servofloat OFF (Control Group No.2).
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat OFF (Control Group No.2).
Specified control group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in servofloat OFF (Control Group No.2).
Specified control group is not supported.
Remedy:
(1) Reset the alarm.
(2) Base axes control group is not supported. Specify robot or station axes control group and execute again.
Description:
Failed in servofloat OFF (Control Group No.2).
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in servofloat OFF (Control Group No.2).
Alarm occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat OFF (Control Group No.2).
Servo power is down.
Remedy:
(1) Reset the alarm.
(2) Turn on the servo power and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.2).
Remedy:
Reset the alarm and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.2).
Specified control group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.2).
Specified servofloat type is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
(3) If the alarm occurs again, confirm that specified servofloat type function is enabled.
Description:
Failed in writing servofloat condition file (Control Group No.2).
Specified servofloat condition file number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat condition file number and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.2).
Specified control group is not supported axis servofloat.
Remedy:
(1) Reset the alarm.
(2) Base axes control group is not supported. Specify robot or station axes control group and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.2).
Specified control group is not supported linear servofloat.
Remedy:
(1) Reset the alarm.
(2) Base and station axes control group is not supported. Specify Robot axes control group and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.2).
Specified coordinate frame is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct coordinate frame and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.2).
Specified max/min torque is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct max/min torque and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.2).
Specified max/min force is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct max/min force and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.2).
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.2).
Alarm occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.2).
Edit inhibited.
Remedy:
(1) Reset the alarm.
(2) Release editlock and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.2).
Remedy:
Reset the alarm and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.2).
Specified control group is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.2).
Specified servofloat type is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
(3) If the alarm occurs again, confirm that specified servofloat type function is enabled.
Description:
Failed in reading servofloat condition file (Control Group No.2).
Specified servofloat condition file is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat condition file number and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.2).
Specified control group is different from specified one in a servofloat condition file.
Remedy:
(1) Reset the alarm.
(2) Change control group number and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.2).
Instruction buffer size is not enough to read.
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetCollisionDetectionStatus command (Control group 2).
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetCollisionDetectionStatus command. (Control group 2)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionStatus command. (Control group 2)
Incorrect status has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command (Control group 2).
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 2)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 2)
Incorrect resource type has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 2)
Incorrect number of file has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 2)
Incorrect value of levels has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 2)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in WriteCollisionDetectionFile command (Control group 2).
Remedy:
Reset the alarm and execute again.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 2)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 2)
Incorrect number of file has been set.
Remedy:
Input correct data.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 2)
Incorrect value of levels has been set.
Remedy:
Input correct data.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 2)
The function parameter has not been set.
Remedy:
Enable Teach Mode Each Axis Setting Function.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 2)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in GetCollisionDetectionStatus command (Control group 2).
Remedy:
Reset the alarm and execute again.
Description:
Failed in GetCollisionDetectionStatus command. (Control group 2)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in GetCollisionDetectionTorque command (Control group 2).
Remedy:
Reset the alarm and execute again.
Description:
Failed in GetCollisionDetectionTorque command. (Control group 2)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in BrakeGroupInfoGet command (Control group2).
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetSearch command (Control Group2).
Remedy:
(1) Confirm option function: “Search function” is enabled.
(2) Reset the alarm and then try again.
Description:
Failed in SetSearch command.(Control Group2)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in SetSearch command.(Control Group2)
Specified control group is not supported search function.
Remedy:
Search function supports only robot.
(1) Reset the alarm.
(2) Specify robot and execute again.
Description:
Failed in SetSearch command.(Control Group2)
Specified InputSignalBits is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct RIN signal and then try again. Incorrect specification is shown below.
(a) It can not be specified 0.
(b) If SearchAction is specified 0, it can not be specified multiple RIN signals.
(c) It can not be specified RIN signal which number is out of range.
Description:
Failed in SetSearch command.(Control Group2)
Specified SearchAction is invalid.
Remedy:
SearchAction can be specified only 0.
(1) Reset the alarm.
(2) Specify 0 to SearchAction and execute again.
Description:
Failed in ResetSearch command (Control Group2).
Remedy:
(1) Confirm option function: “Search function” is enabled.
(2) Reset the alarm and then try again.
Description:
Failed in ResetSearch command.(Control Group2)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in ResetSearch command.(Control Group2)
Specified control group is not supported search function.
Remedy:
Search function supports only robot.
(1) Reset the alarm.
(2) Specify robot and execute again.
Description:
Failed in GetSearchResult command (Control Group2).
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchResult command.(Control Group2)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in GetSearchResult command.(Control Group2)
Specified control group is not supported search function.
Remedy:
Station group can not be specified.
(1) Reset the alarm.
(2) Specify robot or base axes group number and execute again.
Description:
Failed in GetSearchResult command.(Control Group2)
Memory to store result is not enough.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchResult command.(Control Group2)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in GetSearchPosition command (Control Group2).
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group2)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in GetSearchResult command.(Control Group2)
Specified control group is not supported search function.
Remedy:
Station group can not be specified.
(1) Reset the alarm.
(2) Specify robot or base axes group number and execute again.
Description:
Failed in GetSearchPosition command.(Control Group2)
Memory to store result is not enough.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command (Control Group2).
Specified coordinate system is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify world or user coordinate system and execute again.
Description:
Failed in GetSearchPosition command.(Control Group2)
Specified detected number is out of range.
Remedy:
If using search motion with SearchAction is 0, detected number must be 0.
(1) Reset the alarm.
(2) Specify 0 to detected number and execute again.
Description:
Failed in GetSearchPosition command.(Control Group2)
RIN signal has not been detected.
Remedy:
(1) Reset the alarm.
(2) Verify detected count by executing GetSearchResult command.
(3) Execute instruction again if it’s more than 0.
Description:
Failed in GetSearchPosition command.(Control Group2)
Failed in getting detected TCP position.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group2)
Failed in getting detected TCP position in User coordinate system because, user frame had been inactive when search motion was enqueued.
Remedy:
Set active user frame number when execute linear move command with search.
Description:
Failed in GetSearchPosition command.(Control Group2)
Failed in getting detected TCP position in user coordinate system..
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group2)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in MultiMoveOn command (Control group 2).
Remedy:
Reset the alarm and execute again.
Description:
Failed in MultiMoveOn command. (Control group 2)
Specified control group is not supported.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 2)
The system state is illegal.
Remedy:
(1) Reset the alarm.
(2) Confirm the system state and execute again.
Description:
Failed in MultiMoveOn command. (Control group 2)
Multiple control group is not supported.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 2)
The VMAX is not supported for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 2)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 2)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 2)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOff command (Control group 2).
Remedy:
Reset the alarm and execute again.
Description:
Failed in MultiMoveOff command. (Control group 2)
Specified control group is not supported.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOff command. (Control group 2)
Failed to start motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetMultiMoveMinimumBuffer command (Control group 2).
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 2)
Specified control group is not supported.
Remedy:
Input correct data.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 2)
The minimum buffer is out of range.
Remedy:
Input correct data.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 2)
The robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop the robot and execute again.
Description:
Failed in GetProperties command (Control group3).
Remedy:
Input correct data.
Description:
Failed in GetProperties command. (Control group3)
The number of step is out of range.
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command (Control group3).
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group3)
Invalid data of tool has been set.
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group3)
Incorrect number of tool has been set.
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group3)
Failed to write tool file.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command (Control group3).
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group3)
Invalid data of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group3)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group3)
Failed to write user coordinate file.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group3)
Failed to make user coordinate.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group3)
Failed to convert user coordinate.
Remedy:
Input correct data.
Description:
Failed in SetFrameShift command (Control group3).
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in SetFrameShift command. (Control group3)
Failed to set frame shift.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command (Control group3).
Undefined IZ action has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command (Control group3).
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group3)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command (Control group3).
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group3)
Incorrect ID number has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group3)
Failed to write cube file.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command (Control group3).
Undefined IZ action has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command (Control group3).
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group3)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command (Control group3).
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group3)
Incorrect ID number has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group3)
Failed to write cube file.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command (Control group3).
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command (Control group3).
Undefined transform type has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert Axis coordinates to TCP coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert Axis coordinates to TCP coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert TCP coordinates to Axis coordinates.
Incorrect number of tool has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert TCP coordinates to Axis coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert TCP in World frame to User frame.
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert TCP in World frame to User frame.
Failed to convert Input coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert TCP in World frame to User frame.
Failed to convert User coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert TCP in World frame to User frame.
Failed to create inverse matrix of user coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert TCP in World frame to User frame.
Failed in multiplication of coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert TCP in World frame to User frame.
Failed to convert Output coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert TCP in User frame to World frame.
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert TCP in User frame to World frame.
Failed to convert Input coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert TCP in User frame to World frame.
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert TCP in User frame to World frame.
Failed in multiplication of coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group3)
Failed to convert TCP in User frame to World frame.
Failed to convert Output coordinates.
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStart command (Control group3).
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStart command. (Control group3)
Incorrect number of conveyor has been set.
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStart command (Control group3).
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStop command (Control group3).
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStop command (Control group3).
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command (Control group3).
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group3)
The size of command buffer is out of range.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group3)
Failed to read position variable file.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group3)
Failed to convert Pulse coordinates to Axis coordinates.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group3)
Failed to convert Axis coordinates to TCP coordinates.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group3)
Failed to convert TCP coordinates to Axis coordinates.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group3)
Failed to convert TCP in User frame to World frame.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command (Control group3).
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group3)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command (Control group3).
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command (Control group3).
Undefined position type has been set.
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command. (Control group3)
Failed to write position variable file.
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command. (Control group3)
Failed to convert Axis coordinates to Pulse coordinates.
Remedy:
Input correct data.
Description:
Failed in SetBasePose command (Control group3).
Remedy:
Input correct data.
Description:
Failed in SetBasePose command. (Control group3)
Failed to write file.
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command (Control group3).
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command. (Control group3)
Failed to get current position of pulse type.
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command. (Control group3)
Failed to write file.
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command (Control group3).
Undefined offset type has been set.
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command (Control group3).
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command. (Control group3)
Failed to get current position of pulse type.
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command. (Control group3)
Failed to read file.
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command (Control group3).
Undefined offset type has been set.
Remedy:
Input correct data.
Description:
Failed in VarsGet command (Control group3).
Remedy:
Input correct data.
Description:
Failed in VarsGet command (Control group3).
Undefined variable type has been set.
Remedy:
Input correct data.
Description:
Failed in VarsGet command. (Control group3)
Incorrect number of variable has been set.
Remedy:
Input correct data.
Description:
Failed in VarsGet command. (Control group3)
Incorrect number of getting has been set.
Remedy:
Input correct data.
Description:
Failed in VarsSet command (Control group3).
Remedy:
Input correct data.
Description:
Failed in VarsSet command (Control group3).
Undefined variable type has been set.
Remedy:
Input correct data.
Description:
Failed in VarsSet command. (Control group3)
Incorrect number of variable has been set.
Remedy:
Input correct data.
Description:
Failed in VarsSet command. (Control group3)
Incorrect number of setting has been set.
Remedy:
Input correct data.
Description:
Failed in SetProperties command (Control group3).
Remedy:
Input correct data.
Description:
Failed in SetProperties command. (Control group3)
The number of step is out of range.
Remedy:
Input correct data.
Description:
Failed in SetProperties command. (Control group3)
The axis index is out of range.
Remedy:
Input correct data.
Description:
Failed in ToolCalib command (Control group3).
Remedy:
Reset the alarm and execute again.
Description:
Failed in ToolCalib command.(Control group3)
Incorrect number of tool has been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct tool number and execute again.
Description:
Failed in ToolCalib command.(Control group3)
Incorrect number of calibration method has been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct calibration method and execute again.
Description:
Failed in ToolCalib command.(Control group3)
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in ToolCalib command.(Control group3)
The teaching points include the same points.
Remedy:
(1) Reset the alarm.
(2) Set the teaching point to a different point and execute again.
Description:
Failed in ToolCalib command.(Control group3)
An alarm or error is occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in ToolCalib command.(Control group3)
Editing is prohibited.
Remedy:
Reset the alarm and execute again.
Description:
Failed in ToolCalib command.(Control group3)
Specified group is not supported .
Remedy:
(1) Reset the alarm.
(2) Specify robot control group and execute again.
Description:
Failed in ToolCalib command.(Control group3)
The tool calibration function is running.
Remedy:
(1) Reset the alarm.
(2) Stop tool calibration and execute again.
Description:
Failed in ReleaseBrake command (Control group3).
Remedy:
Reset the alarm and execute again.
Description:
Failed in ReleaseBrake command. (Control group3)
Failed to stop manual brake release.
Remedy:
Reset the alarm and execute again.
Description:
Failed in ReleaseBrake command. (Control group3)
Incorrect axes have been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct axes information and execute again.
Description:
Failed in ReleaseBrake command. (Control group3)
ReleaseBrake command was executed when the servo power was ON.
Remedy:
(1) Reset the alarm.
(2) Turn off the servo power and execute again.
Description:
Failed in ReleaseBrake command. (Control group3)
ReleaseBrake command was executed when in emergency stop condition.
Remedy:
(1) Reset the alarm.
(2) Releasing the emergency stop and execute again.
Description:
Failed in ReleaseBrake command. (Control group3)
ReleaseBrake command was executed when the BRK_EN signal was in the release prohibition condition.
Remedy:
(1) Reset the alarm.
(2) Set the BRK_EN signal to release permission condition and execute again.
Description:
Failed in ReleaseBrake command. (Control group3)
Specified axes are lacked.
Remedy:
(1) Reset the alarm.
(2) Check the brake group information.
(3) Specify correct axes and execute again.
Description:
Failed in ReleaseBrake command. (Control group3)
Manual release brake function is invalid.
Remedy:
(1) Reset the alarm.
(2) Enable manual release brake function and execute again.
Description:
Failed in servofloat ON (Control Group No.3).
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat ON (Control Group No.3).
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in servofloat ON (Control Group No.3).
Specified servofloat type is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
(3) If the alarm occurs again, confirm that specified servofloat type function is enabled.
Description:
Failed in servofloat ON (Control Group No.3).
Specified servofloat condition file number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
Description:
Failed in servofloat ON (Control Group No.3).
Specified group is not supported axis servofloat.
Remedy:
(1) Reset the alarm.
(2) Base axes control group is not supported. Specify robot or station axes control group and execute again.
Description:
Failed in servofloat ON (Control Group No.3).
Specified group is not supported linear servofloat.
Remedy:
(1) Reset the alarm.
(2) Base and station axes control group is not supported. Specify Robot axes control group and execute again.
Description:
Failed in servofloat ON (Control Group No.3).
Specified group is different from specified one in a servofloat condition file.
Remedy:
(1) Reset the alarm.
(2) Confirm the group number specified in a servofloat condition file.
(3) Specify that group number and execute again.
Description:
Failed in servofloat ON (Control Group No.3).
Failed in referring servofloat condition file.
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat ON (Control Group No.3).
User frame number is not active.
Remedy:
(1) Reset the alarm.
(2) Set active user frame number and execute again.
Description:
Failed in servofloat ON (Control Group No.3).
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in servofloat ON (Control Group No.3).
Alarm occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat ON (Control Group No.3).
Servo power is down.
Remedy:
(1) Reset the alarm.
(2) Turn on the servo power and execute again.
Description:
Failed in servofloat OFF (Control Group No.3).
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat OFF (Control Group No.3).
Specified control group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in servofloat OFF (Control Group No.3).
Specified control group is not supported.
Remedy:
(1) Reset the alarm.
(2) Base axes control group is not supported. Specify robot or station axes control group and execute again.
Description:
Failed in servofloat OFF (Control Group No.3).
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in servofloat OFF (Control Group No.3).
Alarm occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat OFF (Control Group No.3).
Servo power is down.
Remedy:
(1) Reset the alarm.
(2) Turn on the servo power and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.3).
Remedy:
Reset the alarm and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.3).
Specified control group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.3).
Specified servofloat type is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
(3) If the alarm occurs again, confirm that specified servofloat type function is enabled.
Description:
Failed in writing servofloat condition file (Control Group No.3).
Specified servofloat condition file number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat condition file number and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.3).
Specified control group is not supported axis servofloat.
Remedy:
(1) Reset the alarm.
(2) Base axes control group is not supported. Specify robot or station axes control group and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.3).
Specified control group is not supported linear servofloat.
Remedy:
(1) Reset the alarm.
(2) Base and station axes control group is not supported. Specify Robot axes control group and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.3).
Specified coordinate frame is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct coordinate frame and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.3).
Specified max/min torque is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct max/min torque and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.3).
Specified max/min force is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct max/min force and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.3).
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.3).
Alarm occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.3).
Edit inhibited.
Remedy:
(1) Reset the alarm.
(2) Release editlock and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.3).
Remedy:
Reset the alarm and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.3).
Specified control group is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.3).
Specified servofloat type is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
(3) If the alarm occurs again, confirm that specified servofloat type function is enabled.
Description:
Failed in reading servofloat condition file (Control Group No.3).
Specified servofloat condition file is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat condition file number and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.3).
Specified control group is different from specified one in a servofloat condition file.
Remedy:
(1) Reset the alarm.
(2) Change control group number and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.3).
Instruction buffer size is not enough to read.
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetCollisionDetectionStatus command (Control group 3).
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetCollisionDetectionStatus command. (Control group 3)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionStatus command. (Control group 3)
Incorrect status has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command (Control group 3).
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 3)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 3)
Incorrect resource type has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 3)
Incorrect number of file has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 3)
Incorrect value of levels has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 3)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in WriteCollisionDetectionFile command (Control group 3).
Remedy:
Reset the alarm and execute again.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 3)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 3)
Incorrect number of file has been set.
Remedy:
Input correct data.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 3)
Incorrect value of levels has been set.
Remedy:
Input correct data.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 3)
The function parameter has not been set.
Remedy:
Enable Teach Mode Each Axis Setting Function.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 3)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in GetCollisionDetectionStatus command. (Control group 3).
Remedy:
Reset the alarm and execute again.
Description:
Failed in GetCollisionDetectionStatus command. (Control group 3)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in GetCollisionDetectionTorque command. (Control group 3).
Specified control group is not a robot.
Remedy:
Reset the alarm and execute again.
Description:
Failed in GetCollisionDetectionTorque command. (Control group 3)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in BrakeGroupInfoGet command. (Control group3).
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetSearch command.(Control Group3).
Remedy:
(1) Confirm option function: “Search function” is enabled.
(2) Reset the alarm and then try again.
Description:
Failed in SetSearch command.(Control Group3)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in SetSearch command.(Control Group3)
Specified control group is not supported search function.
Remedy:
Search function supports only robot.
(1) Reset the alarm.
(2) Specify robot and execute again.
Description:
Failed in SetSearch command.(Control Group3)
Specified InputSignalBits is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct RIN signal and then try again. Incorrect specification is shown below.
(a) It can not be specified 0.
(b) If SearchAction is specified 0, it can not be specified multiple RIN signals.
(c) It can not be specified RIN signal which number is out of range.
Description:
Failed in SetSearch command.(Control Group3)
Specified SearchAction is invalid.
Remedy:
SearchAction can be specified only 0.
(1) Reset the alarm.
(2) Specify 0 to SearchAction and execute again.
Description:
Failed in ResetSearch command.(Control Group3).
Remedy:
(1) Confirm option function: “Search function” is enabled.
(2) Reset the alarm and then try again.
Description:
Failed in ResetSearch command.(Control Group3)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in ResetSearch command.(Control Group3)
Specified control group is not supported search function.
Remedy:
Search function supports only robot.
(1) Reset the alarm.
(2) Specify robot and execute again.
Description:
Failed in GetSearchResult command.(Control Group3).
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchResult command.(Control Group3)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in GetSearchResult command.(Control Group3)
Specified control group is not supported search function.
Remedy:
Station group can not be specified.
(1) Reset the alarm.
(2) Specify robot or base axes group number and execute again.
Description:
Failed in GetSearchResult command.(Control Group3)
Memory to store result is not enough.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchResult command.(Control Group3)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in GetSearchPosition command.(Control Group3).
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group3)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in GetSearchResult command.(Control Group3)
Specified control group is not supported search function.
Remedy:
Station group can not be specified.
(1) Reset the alarm.
(2) Specify robot or base axes group number and execute again.
Description:
Failed in GetSearchPosition command.(Control Group3)
Memory to store result is not enough.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group3).
Specified coordinate system is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify world or user coordinate system and execute again.
Description:
Failed in GetSearchPosition command.(Control Group3)
Specified detected number is out of range.
Remedy:
If using search motion with SearchAction is 0, detected number must be 0.
(1) Reset the alarm.
(2) Specify 0 to detected number and execute again.
Description:
Failed in GetSearchPosition command.(Control Group3)
RIN signal has not been detected.
Remedy:
(1) Reset the alarm.
(2) Verify detected count by executing GetSearchResult command.
(3) Execute instruction again if it’s more than 0.
Description:
Failed in GetSearchPosition command.(Control Group3)
Failed in getting detected TCP position.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group3)
Failed in getting detected TCP position in User coordinate system because, user frame had been inactive when search motion was enqueued.
Remedy:
Set active user frame number when execute linear move command with search.
Description:
Failed in GetSearchPosition command.(Control Group3)
Failed in getting detected TCP position in user coordinate system..
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group3)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in MultiMoveOn command. (Control group 3).
Remedy:
Reset the alarm and execute again.
Description:
Failed in MultiMoveOn command. (Control group 3)
Specified control group is not supported.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 3)
The system state is illegal.
Remedy:
(1) Reset the alarm.
(2) Confirm the system state and execute again.
Description:
Failed in MultiMoveOn command. (Control group 3)
Multiple control group is not supported.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 3)
The VMAX is not supported for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 3)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 3)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 3)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOff command. (Control group 3).
Remedy:
Reset the alarm and execute again.
Description:
Failed in MultiMoveOff command. (Control group 3)
Specified control group is not supported.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOff command. (Control group 3)
Failed to start motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 3).
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 3)
Specified control group is not supported.
Remedy:
Input correct data.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 3)
The minimum buffer is out of range.
Remedy:
Input correct data.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 3)
The robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop the robot and execute again.
Description:
Failed in GetProperties command. (Control group4).
The number of step is out of range.
Remedy:
Input correct data.
Description:
Failed in GetProperties command. (Control group4)
The number of step is out of range.
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group4)
Invalid data of tool has been set.
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group4)
Incorrect number of tool has been set.
Remedy:
Input correct data.
Description:
Failed in SetToolProperties command. (Control group4)
Failed to write tool file.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group4)
Invalid data of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group4)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group4)
Failed to write user coordinate file.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group4)
Failed to make user coordinate.
Remedy:
Input correct data.
Description:
Failed in SetUserFrame command. (Control group4)
Failed to convert user coordinate.
Remedy:
Input correct data.
Description:
Failed in SetFrameShift command. (Control group4).
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in SetFrameShift command. (Control group4)
Failed to set frame shift.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group4).
Undefined IZ action has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group4).
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group4)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group4)
Incorrect ID number has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByCenterPoint command. (Control group4)
Failed to write cube file.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group4).
Undefined IZ action has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group4).
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group4)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group4)
Incorrect ID number has been set.
Remedy:
Input correct data.
Description:
Failed in SetCubicIZByTwoCorners command. (Control group4)
Failed to write cube file.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4).
Undefined transform type has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert Axis coordinates to TCP coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert Axis coordinates to TCP coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert TCP coordinates to Axis coordinates.
Incorrect number of tool has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert TCP coordinates to Axis coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert TCP in World frame to User frame.
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert TCP in World frame to User frame.
Failed to convert Input coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert TCP in World frame to User frame.
Failed to convert User coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert TCP in World frame to User frame.
Failed to create inverse matrix of user coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert TCP in World frame to User frame.
Failed in multiplication of coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert TCP in World frame to User frame.
Failed to convert Output coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert TCP in User frame to World frame.
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert TCP in User frame to World frame.
Failed to convert Input coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert TCP in User frame to World frame.
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert TCP in User frame to World frame.
Failed in multiplication of coordinates.
Remedy:
Input correct data.
Description:
Failed in CoordinateTransform command. (Control group4)
Failed to convert TCP in User frame to World frame.
Failed to convert Output coordinates.
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStart command. (Control group4).
Incorrect number of conveyor has been set.
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStart command. (Control group4)
Incorrect number of conveyor has been set.
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStart command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStop command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in ConveyorSyncStop command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group4)
The size of command buffer is out of range.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group4)
Failed to read position variable file.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group4)
Failed to convert Pulse coordinates to Axis coordinates.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group4)
Failed to convert Axis coordinates to TCP coordinates.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group4)
Failed to convert TCP coordinates to Axis coordinates.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group4)
Failed to convert TCP in User frame to World frame.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group4).
Undefined coordinate system has been set.
Remedy:
Input correct data.
Description:
Failed in PositionVariableGet command. (Control group4)
Incorrect number of user coordinate has been set.
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command. (Control group4).
Undefined position type has been set.
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command. (Control group4)
Failed to write position variable file.
Remedy:
Input correct data.
Description:
Failed in PositionVariableSet command. (Control group4)
Failed to convert Axis coordinates to Pulse coordinates.
Remedy:
Input correct data.
Description:
Failed in SetBasePose command. (Control group4).
Failed to write file.
Remedy:
Input correct data.
Description:
Failed in SetBasePose command. (Control group4)
Failed to write file.
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command. (Control group4)
Failed to get current position of pulse type.
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command. (Control group4)
Failed to write file.
Remedy:
Input correct data.
Description:
Failed in SetHomeOffsets command. (Control group4).
Undefined offset type has been set.
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command. (Control group4)
Failed to get current position of pulse type.
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command. (Control group4)
Failed to read file.
Remedy:
Input correct data.
Description:
Failed in GetHomeOffsets command. (Control group4).
Undefined offset type has been set.
Remedy:
Input correct data.
Description:
Failed in VarsGet command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in VarsGet command. (Control group4).
Undefined variable type has been set.
Remedy:
Input correct data.
Description:
Failed in VarsGet command. (Control group4)
Incorrect number of variable has been set.
Remedy:
Input correct data.
Description:
Failed in VarsGet command. (Control group4)
Incorrect number of getting has been set.
Remedy:
Input correct data.
Description:
Failed in VarsSet command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in VarsSet command. (Control group4).
Undefined variable type has been set.
Remedy:
Input correct data.
Description:
Failed in VarsSet command. (Control group4)
Incorrect number of variable has been set.
Remedy:
Input correct data.
Description:
Failed in VarsSet command. (Control group4)
Incorrect number of setting has been set.
Remedy:
Input correct data.
Description:
Failed in SetProperties command. (Control group4).
Remedy:
Input correct data.
Description:
Failed in SetProperties command. (Control group4)
The number of step is out of range.
Remedy:
Input correct data.
Description:
Failed in SetProperties command. (Control group4)
The axis index is out of range.
Remedy:
Input correct data.
Description:
Failed in ToolCalib command.(Control group4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in ToolCalib command.(Control group4)
Incorrect number of tool has been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct tool number and execute again.
Description:
Failed in ToolCalib command.(Control group4)
Incorrect number of calibration method has been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct calibration method and execute again.
Description:
Failed in ToolCalib command.(Control group4)
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in ToolCalib command.(Control group4)
The teaching points include the same points.
Remedy:
(1) Reset the alarm.
(2) Set the teaching point to a different point and execute again.
Description:
Failed in ToolCalib command.(Control group4)
An alarm or error is occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in ToolCalib command.(Control group4)
Editing is prohibited.
Remedy:
Reset the alarm and execute again.
Description:
Failed in ToolCalib command.(Control group4)
Specified group is not supported .
Remedy:
(1) Reset the alarm.
(2) Specify robot control group and execute again.
Description:
Failed in ToolCalib command.(Control group4)
The tool calibration function is running.
Remedy:
(1) Reset the alarm.
(2) Stop tool calibration and execute again.
Description:
Failed in ReleaseBrake command. (Control group4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in ReleaseBrake command. (Control group4)
Failed to stop manual brake release.
Remedy:
Reset the alarm and execute again.
Description:
Failed in ReleaseBrake command. (Control group4)
Incorrect axes have been set.
Remedy:
(1) Reset the alarm.
(2) Specify correct axes information and execute again.
Description:
Failed in ReleaseBrake command. (Control group4)
ReleaseBrake command was executed when the servo power was ON.
Remedy:
(1) Reset the alarm.
(2) Turn off the servo power and execute again.
Description:
Failed in ReleaseBrake command. (Control group4)
ReleaseBrake command was executed when in emergency stop condition.
Remedy:
(1) Reset the alarm.
(2) Releasing the emergency stop and execute again.
Description:
Failed in ReleaseBrake command. (Control group4)
ReleaseBrake command was executed when the BRK_EN signal was in the release prohibition condition.
Remedy:
(1) Reset the alarm.
(2) Set the BRK_EN signal to release permission condition and execute again.
Description:
Failed in ReleaseBrake command. (Control group4)
Specified axes are lacked.
Remedy:
(1) Reset the alarm.
(2) Check the brake group information.
(3) Specify correct axes and execute again.
Description:
Failed in ReleaseBrake command. (Control group4)
Manual release brake function is invalid.
Remedy:
(1) Reset the alarm.
(2) Enable manual release brake function and execute again.
Description:
Failed in servofloat ON (Control Group No.4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat ON (Control Group No.4).
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in servofloat ON (Control Group No.4).
Specified servofloat type is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
(3) If the alarm occurs again, confirm that specified servofloat type function is enabled.
Description:
Failed in servofloat ON (Control Group No.4).
Specified servofloat condition file number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
Description:
Failed in servofloat ON (Control Group No.4).
Specified group is not supported axis servofloat.
Remedy:
(1) Reset the alarm.
(2) Base axes control group is not supported. Specify robot or station axes control group and execute again.
Description:
Failed in servofloat ON (Control Group No.4).
Specified group is not supported linear servofloat.
Remedy:
(1) Reset the alarm.
(2) Base and station axes control group is not supported. Specify Robot axes control group and execute again.
Description:
Failed in servofloat ON (Control Group No.4).
Specified group is different from specified one in a servofloat condition file.
Remedy:
(1) Reset the alarm.
(2) Confirm the group number specified in a servofloat condition file.
(3) Specify that group number and execute again.
Description:
Failed in servofloat ON (Control Group No.4).
Failed in referring servofloat condition file.
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat ON (Control Group No.4).
User frame number is not active.
Remedy:
(1) Reset the alarm.
(2) Set active user frame number and execute again.
Description:
Failed in servofloat ON (Control Group No.4).
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in servofloat ON (Control Group No.4).
Alarm occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat ON (Control Group No.4).
Servo power is down.
Remedy:
(1) Reset the alarm.
(2) Turn on the servo power and execute again.
Description:
Failed in servofloat OFF (Control Group No.4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat OFF (Control Group No.4).
Specified control group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in servofloat OFF (Control Group No.4).
Specified control group is not supported.
Remedy:
(1) Reset the alarm.
(2) Base axes control group is not supported. Specify robot or station axes control group and execute again.
Description:
Failed in servofloat OFF (Control Group No.4).
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in servofloat OFF (Control Group No.4).
Alarm occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in servofloat OFF (Control Group No.4).
Servo power is down.
Remedy:
(1) Reset the alarm.
(2) Turn on the servo power and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.4).
Specified control group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.4).
Specified servofloat type is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
(3) If the alarm occurs again, confirm that specified servofloat type function is enabled.
Description:
Failed in writing servofloat condition file (Control Group No.4).
Specified servofloat condition file number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat condition file number and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.4).
Specified control group is not supported axis servofloat.
Remedy:
(1) Reset the alarm.
(2) Base axes control group is not supported. Specify robot or station axes control group and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.4).
Specified control group is not supported linear servofloat.
Remedy:
(1) Reset the alarm.
(2) Base and station axes control group is not supported. Specify Robot axes control group and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.4).
Specified coordinate frame is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct coordinate frame and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.4).
Specified max/min torque is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct max/min torque and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.4).
Specified max/min force is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct max/min force and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.4).
Robot moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.4).
Alarm occurring.
Remedy:
Reset the alarm and execute again.
Description:
Failed in writing servofloat condition file (Control Group No.4).
Edit inhibited.
Remedy:
(1) Reset the alarm.
(2) Release editlock and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.4).
Specified control group is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct control group number and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.4).
Specified servofloat type is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat type and execute again.
(3) If the alarm occurs again, confirm that specified servofloat type function is enabled.
Description:
Failed in reading servofloat condition file (Control Group No.4).
Specified servofloat condition file is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct servofloat condition file number and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.4).
Specified control group is different from specified one in a servofloat condition file.
Remedy:
(1) Reset the alarm.
(2) Change control group number and execute again.
Description:
Failed in reading servofloat condition file (Control Group No.4).
Instruction buffer size is not enough to read.
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetCollisionDetectionStatus command. (Control group 4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetCollisionDetectionStatus command. (Control group 4)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionStatus command. (Control group 4)
Incorrect status has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 4)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 4)
Incorrect resource type has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 4)
Incorrect number of file has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 4)
Incorrect value of levels has been set.
Remedy:
Input correct data.
Description:
Failed in SetCollisionDetectionLevels command. (Control group 4)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 4)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 4)
Incorrect number of file has been set.
Remedy:
Input correct data.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 4)
Incorrect value of levels has been set.
Remedy:
Input correct data.
Description:
Failed in WriteCollisionDetectionFile command. (Control group 4)
The function parameter has not been set.
Remedy:
Enable Teach Mode Each Axis Setting Function
Description:
Failed in WriteCollisionDetectionFile command. (Control group 4)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in GetCollisionDetectionStatus command. (Control group 4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in GetCollisionDetectionStatus command. (Control group 4)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in GetCollisionDetectionTorque command. (Control group 4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in GetCollisionDetectionTorque command. (Control group 4)
Specified control group is not a robot.
Remedy:
Input correct data.
Description:
Failed in BrakeGroupInfoGet command. (Control group4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetSearch command.(Control Group4).
Remedy:
(1) Confirm option function: “Search function” is enabled.
(2) Reset the alarm and then try again.
Description:
Failed in SetSearch command.(Control Group4)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in SetSearch command.(Control Group4)
Specified control group is not supported search function.
Remedy:
Search function supports only robot.
(1) Reset the alarm.
(2) Specify robot and execute again.
Description:
Failed in SetSearch command.(Control Group4)
Specified InputSignalBits is invalid.
Remedy:
(1) Reset the alarm.
(2) Specify correct RIN signal and then try again. Incorrect specification is shown below.
(a) It can not be specified 0.
(b) If SearchAction is specified 0, it can not be specified multiple RIN signals.
(c) It can not be specified RIN signal which number is out of range.
Description:
Failed in SetSearch command.(Control Group4)
Specified SearchAction is invalid.
Remedy:
SearchAction can be specified only 0.
(1) Reset the alarm.
(2) Specify 0 to SearchAction and execute again.
Description:
Failed in ResetSearch command.(Control Group4).
Remedy:
(1) Confirm option function: “Search function” is enabled.
(2) Reset the alarm and then try again.
Description:
Failed in ResetSearch command.(Control Group4)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in ResetSearch command.(Control Group4)
Specified control group is not supported search function.
Remedy:
Search function supports only robot.
(1) Reset the alarm.
(2) Specify robot and execute again.
Description:
Failed in GetSearchResult command.(Control Group4).
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchResult command.(Control Group4)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in GetSearchResult command.(Control Group4)
Specified control group is not supported search function.
Remedy:
Station group can not be specified.
(1) Reset the alarm.
(2) Specify robot or base axes group number and execute again.
Description:
Failed in GetSearchResult command.(Control Group4)
Memory to store result is not enough.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchResult command.(Control Group4)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in GetSearchPosition command.(Control Group4).
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group4)
Specified group number is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify correct group number and execute again.
Description:
Failed in GetSearchResult command.(Control Group4)
Specified control group is not supported search function.
Remedy:
Station group can not be specified.
(1) Reset the alarm.
(2) Specify robot or base axes group number and execute again.
Description:
Failed in GetSearchPosition command.(Control Group4)
Memory to store result is not enough.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group4).
Specified coordinate system is out of range.
Remedy:
(1) Reset the alarm.
(2) Specify world or user coordinate system and execute again.
Description:
Failed in GetSearchPosition command.(Control Group4)
Specified detected number is out of range.
Remedy:
If using search motion with SearchAction is 0, detected number must be 0.
(1) Reset the alarm.
(2) Specify 0 to detected number and execute again.
Description:
Failed in GetSearchPosition command.(Control Group4)
RIN signal has not been detected.
Remedy:
(1) Reset the alarm.
(2) Verify detected count by executing GetSearchResult command.
(3) Execute instruction again if it’s more than 0.
Description:
Failed in GetSearchPosition command.(Control Group4)
Failed in getting detected TCP position.
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group4)
Failed in getting detected TCP position in User coordinate system because, user frame had been inactive when search motion was enqueued.
Remedy:
Set active user frame number when execute linear move command with search.
Description:
Failed in GetSearchPosition command.(Control Group4)
Failed in getting detected TCP position in user coordinate system..
Remedy:
Reset the alarm, and then try again.
Description:
Failed in GetSearchPosition command.(Control Group4)
Robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop robot and execute again.
Description:
Failed in MultiMoveOn command. (Control group 4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in MultiMoveOn command. (Control group 4)
Specified control group is not supported.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 4)
The system state is illegal.
Remedy:
(1) Reset the alarm.
(2) Confirm the system state and execute again.
Description:
Failed in MultiMoveOn command. (Control group 4)
Multiple control group is not supported.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 4)
The VMAX is not supported for multi move motion.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 4)
The speed is out of range.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 4)
The acceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOn command. (Control group 4)
The deceleration is out of range.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOff command. (Control group 4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in MultiMoveOff command. (Control group 4)
Specified control group is not supported.
Remedy:
Input correct data.
Description:
Failed in MultiMoveOff command. (Control group 4)
Failed to start motion.
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 4).
Remedy:
Reset the alarm and execute again.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 4)
Specified control group is not supported.
Remedy:
Input correct data.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 4)
The minimum buffer is out of range.
Remedy:
Input correct data.
Description:
Failed in SetMultiMoveMinimumBuffer command. (Control group 4)
The robot is moving.
Remedy:
(1) Reset the alarm.
(2) Stop the robot and execute again.
Description:
Connection failed.
Remedy:
(1) Check connector of the cable is inserted correctly.
(2) Check the checksum value. If the checksum value is not correct, send data will be ignored.
(3) Change limit time parameter (S3C[1381]). The unit is [sec]. If set to 0, limit time will be infinite.
Description:
Disconnected.
Remedy:
(1) Check connector of the cable is inserted correctly.
(2) Check the checksum value. If the checksum value is not correct, send data will be ignored
(3) Change watchdog timer parameter (S3C[1380]). The unit is [msec]. If set to 0, watchdog timer will be default time.
Description:
Checksum value is incorrect.
Remedy:
Check the checksum value in send data.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Content:
Disconnection of the regenerative resistor cable and failure of the regenerative transistor are suspected.
Remedy:
Check the connection of regenerative resistor cable.
Content:
The regenerative energy at motor deceleration exceeded the allowable limit.
Remedy:
Check the following settings.
Content:
The SERVOPACK main circuit DC voltage is incorrect.
Remedy:
Check the SERVOPACK Primary supply voltage.
Content:
The SERVOPACK main circuit DC voltage is incorrect.
Remedy:
Check the SERVOPACK Primary supply voltage.
Content:
The rotation speed of the servo motor is incorrect.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Content:
The motor become overloading.
The motor torque greatly exceeded the rated torque.
Remedy:
Check the settings for manipulator motion condition (influence by external force, load condition).
Content:
The motor torque continuously exceeded the rated torque for a certain period.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the SERVOPACK.
Content:
The energy has been when the DB (the dynamic brake) suspended exceeded the capacity of the DB resistor.
Remedy:
Check the settings for manipulator motion condition (influence by external force, load condition).
Content:
There is a possibility of frequently repeating ON/OFF in the main circuit power supply.
Remedy:
Reduce the frequency of the main circuit power supply ON/OFF.
Content:
The temperatures of the SERVOPACK heat sink exceeds 100 degrees.
Remedy:
Check the settings for manipulator motion condition (influence by external force, load condition).
Content:
The voltage drop of encoder backup battery is suspected.
Remedy:
Check the connection of encoder backup battery.
Content:
The internal temperature of the encoder is incorrect.
Remedy:
Check the settings for manipulator motion condition (influence by external force, load condition).
Content:
The A/D converter for speed instruction inputting or the variable data is incorrect.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the SERVOPACK.
Content:
The A/D converter of torque command input error.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the SERVOPACK.
Content:
The direction of the torque and the speed was detected as being the opposite of what it was supposed to be.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Content:
The position deviation pulse exceeds the threshold.
Remedy:
Check the settings for manipulator motion condition (influence by external force, load condition).
Content:
Either of voltage to the SERVOPACK of the three phase input power supply has decreased.
Remedy:
Modify the primary breaker voltage to the voltage specified for the power supply on the rated label on the door of the controller.
Content:
The motor become overloading.
Remedy:
Check the settings for manipulator motion condition (influence by external force, load condition).
Content:
The regenerative energy at motor deceleration exceeded the allowable limit.
Remedy:
Check the following settings.
Content:
MECHATROLINK communications data setting error
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Content:
MECHATROLINK communications command is incorrect.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Content:
MECHATROLINK communications is incorrect.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Content:
The voltage drop is occurred.
Remedy:
Correct the primary power supply.
Content:
The warning sign of voltage reduction of battery for absolute encoder.
Remedy:
Check the battery connection.
Content:
The three phase power supply to the SERVOPACK is not input.
Remedy:
Correct the primary power supply.
Content:
The positioning has not completed.
Remedy:
Check the settings for manipulator motion condition (influence by external force, load condition).
Content:
The position deviation pulse exceeded the allowable limit.
Remedy:
Check the setting of the manipulator’s operation condition such as external force, load condition and so on
Content:
The pole detection in the linear encoder has not been completed.
Remedy:
Replace the linear encoder.
Content:
Speed control could not be executed in the specified axis.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
Force control system detected the excessive external force.
Remedy:
(1) Reset the alarm, and then check the direction of the external force looking at subcode(the direction is based on the sensor coordinate system), and operate robot to move in the direction releasing external force.
(2) If the alarm occurs again, save the CMOS.BIN in maintenance mode, and then contact your YASKAWA representative about occurrence status (operating procedure)
Content:
Force control system detected the excessive axis angular velocity correction.
Remedy:
(1) Reset the alarm, and then make the reference force smaller or operate robot to move in the direction releasing external force.
(2) If the alarm occurs again, save the CMOS.BIN in maintenance mode, and then contact your YASKAWA representative about occurrence status (operating procedure)
Content:
Force control system detected the singular posture.
Remedy:
(1) Reset the alarm, and then modify the toughed robot posture avoiding singularity points.
(2) If the alarm occurs again, save the CMOS.BIN in maintenance mode, and then contact your YASKAWA representative about occurrence status (operating procedure)
Description:
Sub Code: channel
Remedy:
(1) Reset the alarm and decrease the motion speed in JOB.
(2) If the alarm occurs again, save the CMOS.BIN in the maintenance mode and contact your YASKAWA representative about occurrence status (operating procedure).
Content:
YASKAWA force control function is unavailable.
Remedy:
(1) Reset the alarm, and purchase the YASKAWA force control function.
(2) If the alarm occurs again, save the CMOS.BIN in maintenance mode, and then contact your YASKAWA representative about occurrence status (operating procedure)
Description:
Sub Code: channel
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN in the maintenance mode and contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The specified force control file is for other manipulator.
Remedy:
Reset the alarm and check the force control file. The robot of instruction does not match the robot of force control file. Change the file number or the settings of force control file.
Description:
Sub Code: wrong condition
D0:tool number error
D1:coordinate type error
D2:singularity area error
D3:inertia coefficient error
D4:viscosity coefficient error
D5:stifness coefficient error
D6:position limit error
D7:velocity limit error
D8:angular velocity limit error
D9:angular velocity alarm error
D10:contact stabilizing parameter error
Remedy:
(1) Reset the alarm, and then modify the parameter in the referred motoplus application program.
(2) If the alarm occurs again, save the CMOS.BIN in maintenance mode, and then contact your YASKAWA representative about occurrence status (operating procedure)
Description:
Force sensor output error
Remedy:
(1) Reset the alarm, and then release external forces applied to force sensor if the forces are excessive.
(2) If the alarm occurs again, force sensor is faulty.
Please contact your Yaskawa representative.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Reset the alarm, and then check the relationship between the set force command value and the valid axial direction.
Description:
Argument error occurs in mpFcsForceConvScale().
Sub Code:erroneous argument value
Remedy:
Reset the alarm, and then check the argument value related to scale.
Description:
Force control parameter error
Remedy:
Reset the alarm and check the tags of the instruction.
Description:
Excessive force detected
Remedy:
(1) Reset the alarm and check the force sensor. Too large force has detected in force sensor.
(2) If the alarm occurs again, save the CMOS.BIN in the maintenance mode and contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Overspeed
Remedy:
Reset the alarm and decrease the motion speed in JOB.
Description:
Singular point error
Remedy:
Reset the alarm and check the posture of the robot. Change the JOB to avoid the singular point.
Description:
Board / cable error
Remedy:
(1) Check the force sensor, the sensor board, and the cable of force sensor.
(2) If the alarm occurs again, check the connection of sensor board to the controller.
(3) If the alarm occurs again, save the CMOS.BIN in the maintenance mode and contact your YASKAWA representative about occurrence status (operating procedure).
Content:
Force control system detected the overspeed.
Remedy:
(1) Reset the alarm, and then ease the velocity or check whether the posture is singular .
(2) If the alarm occurs again, save the CMOS.BIN in maintenance mode, and then contact your YASKAWA representative about occurrence status (operating procedure)
Content:
Force control system detected the overspeed.
Remedy:
(1) Reset the alarm, and then ease the velocity or check whether the posture is singular .
(2) If the alarm occurs again, save the CMOS.BIN in maintenance mode, and then contact your YASKAWA representative about occurrence status (operating procedure)
Content:
Force control system detected the overspeed.
Remedy:
(1) Reset the alarm, and then ease the velocity or check whether the posture is singular .
(2) If the alarm occurs again, save the CMOS.BIN in maintenance mode, and then contact your YASKAWA representative about occurrence status (operating procedure)
Description:
Sub Code: Group, axis, and interference area number
Remedy:
Check the following settings.
Description:
Sub Code: Group and interference area number
Remedy:
Check the following settings.
Description:
Sub Code: Group, axis, and interference area number
Remedy:
Check the following settings.
Description:
Maximum number of the cube interference area exceeds the allowable range.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The number of cube interference area whose monitoring part is “whole” exceeds the limit.
Remedy:
Reduce the number of cube interference area whose monitoring part is “whole” .
Description:
Detect the cube whose interference area are extremely big or small.
Remedy:
(1) Among the cube interference areas already values are entered, modify as follows.
Description:
Detect the cube interference area whose monitoring part is set to “whole” despite the invalid status of cube arm interference check function.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs just after loading the cube interference area setting function, execute the following measures.
(a) Among the cube interference areas to be loaded, change the monitoring part setting from “whole” to “control point”.
(b) Load the modified cube interference area.
(c) Confirm the settings if the alarm occurs again after the loading operation.
(3) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub code:
SKCHK mode release error
Remedy:
(1) Reset the alarm and decrease the motion speed in JOB.
(2) If the alarm occurs again, save the CMOS.BIN in the maintenance mode and contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub code:
Robot number error
Remedy:
(1) Reset the alarm and change the robot number.
(2) If the alarm occurs again, save the CMOS.BIN in the maintenance mode and contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Control group designation error.
Remedy:
(1) Reset the alarm.
(2) Check the settings for the specified control group number.
Description:
Speed control axis designation error.
Remedy:
(1) Reset the alarm.
(2) Check the settings for the specified speed control axis number.
Description:
Maximum rotation speed over.
Remedy:
(1) Reset the alarm.
(2) Set the rotation speed that does not exceed the maximum rotation speed.
Content:
The function which is not allowed in TEST RUN(HIGH ACCURACY) was performed.
Remedy:
Select a sub menu [TEACHING CONDITION SETTING] under main menu [SETUP].
Set “TEST RUN CONTROL " to “NORMAL” .
Description:
The output signal to the safety PLC does not match between CPU1 and CPU2.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please re-power on the safety PLC and the robot controller.
Description:
In the output signal to the safety PLC, CPU1 could not confirm the update of CPU2 within the specified time.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please re-power on the safety PLC and the robot controller.
Description:
In the output signal to the safety PLC, CPU2 could not confirm the update of CPU1 within the specified time.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please re-power on the safety PLC and the robot controller.
Description:
PROFIsafe communication was not established to the default time, or communication was disconnected after establishment.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
Description:
CIP Safety communication was not established to the default time.(sub code is not defined )
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please re-power on the safety PLC and the robot controller.
Description:
CIP Safety communication was not established to the default time.(CIP Safety stack is under the Self-diagnosis)
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please re-power on the safety PLC and the robot controller.
Description:
CIP Safety communication was not established to the default time.(Waiting for communication establish)
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, the connection setup of EtherNet/IP (CPU board) or safety PLC may not be performed normally.
Please set up again according to a manual.
Description:
CIP Safety communication was not established to the default time.(Exception generating under CIP Safety stack self-diagnosis )
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please re-power on the safety PLC and the robot controller.
Description:
CIP Safety communication was not established to the default time.(Abort of CIP Safety stack processing )
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please re-power on the safety PLC and the robot controller.
Description:
CIP Safety communication was not established to the default time.(Waiting for TUNID configuration)
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please carry out the following according to a manual.
Description:
Value of F_Dest_Add do not match.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following F-Parameter settings.
The value of F_Dest_Add that is set to the safety PLC and the CP1616 board are the same.
Description:
Value of F_Dest_Add is out of range.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following F-Parameter settings.
The value of F_Dest_Add that is set to the safety PLC and the CP1616 board is in the range of 1-65534.
Description:
Value of F_Src_Add is out of range.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following F-Parameter settings.
The value of F_Src_Add that is set to the safety PLC is in the range of 1-65534.
Description:
Value of F_WD_Time is 0.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following F-Parameter settings.
The value of F_WD_Time that is set to the safety PLC is 1 or more.
Description:
Value of F_SIL is invalid.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following F-Parameter settings.
Description:
Value of F_Par_Version is invalid.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following F-Parameter settings.
Description:
Value of F_Par_CRC do not match.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following F-Parameter settings.
Description:
Setting the value of the F-Parameter is invalid.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following F-Parameter settings.
Description:
Value of F_Src_Add do not match.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board.
Description:
Value of F_iPar_CRC is invalid.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following F-Parameter settings.
Description:
Value of F_CRC_Length is invalid.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following F-Parameter settings.
Description:
Value of F_Block_ID is invalid.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following F-Parameter settings.
Description:
F-Parameter check processing was performed during the transfer of safety I/O signals to and from the safety PLC.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board.
Description:
PROFIsafe config processing was performed during the transfer of safety I/O signals with the safety PLC, or during initialization processing.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the ASF01 board.
Description:
Processing of safety field bus does not start.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please turn the power OFF then back ON.
Description:
Communication error of safety field bus occurred.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the connection or insertion state of cables connected to the CP1616 board and safety PLC.
Description:
Watchdog time error of safety field bus occurred.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the connection or insertion state of cables connected to the CP1616 board and safety PLC.
Description:
Passivated state.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, it is necessary to release the passivated state.
Please operate the safety program with the setting tool (TIA Portal) made by SIEMENS and perform the reintegration operation. Alternatively, if the signal for forcibly performing passivation in the safety program is ON, turn it OFF.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH1) occurred.
When the subcode is displayed by 5 digits as 2XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
A CIP Safety communication error (CH2) occurred.
When the subcode is displayed by 5 digits as 3XXYY, the status of the output side/input side is indicated by each 2 digits (XX/YY).
XX: Status of the output side
YY: Status of the input side
The meaning of the values of XX and YY are as follows.
00: No error cause recorded
01: Timeout occurred
02: CRC error
03: Data is dropped due to error received in Time Coordination Message
04: Data is dropped due to inconsistencies in the (CH1) and (CH2)
05: General error
06: Invalid communication connection
90: Output data mismatch between CPUs
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please check the following.
In the case of EtherNet/IP Safety, please check the connection or insertion state of cables connected to the “CN106 connector of ACP01 board” and safety PLC. If a HUB is installed between the safety PLC and the ACP01 board, make sure that the HUB is installed and connected correctly and working normally.
In the case of DeviceNet Safety, please check the connection or insertion state of cables connected to the SST-DN4-PCIE (DeviceNet) board and safety PLC. Make sure that the DeviceNet communication power supply is installed and connected correctly and is working normally.
Description:
Unused A_BANK does not exist in the prereading processing of move instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Unused bank priority does not exist in the prereading processing of move instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
A_BANK pointer is not set.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
A_BANK conversion could not be performed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The specified A_BANK number does not exist.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when system number (MSS) was obtained.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in RMS960 system call.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Undefined interrupt command was received.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Job start condition is not defined.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in instruction prefetch queue operation.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Intermediate code is not defined.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Instruction prereading processing has not been completed normally.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in job data change.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The specified sequence number at job execution start is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The added area for interruption command is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
System number (MSS) for interruption command is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred at start of twin synchronous operation.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when SYNC specification was reset.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in occupation control group setting in MOTION section.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in path/trace control.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when waiting for a completion of main system task (job) in SYNC specification.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An attempt was made to execute an instruction that could not be executed at line sequence execution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred while obtaining the instruction information.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An exceptional error occurred in job execution process.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Main processing command is incorrect in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Subprocessing command is incorrect in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Prereading processing has not been completed at job execution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
A_BANK conversion has not been completed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
System number (MSS) is incorrect in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in instruction prefetch queue operation in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred at IES switching in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in prereading operation process.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The specified sequence number is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An attempt was made to execute an instruction that could not be executed in P-PLC program.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Unused A_BANK does not exist in the prereading processing of move instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Unused bank priority does not exist in the prereading processing of move instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
A_BANK pointer is not set.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
A_BANK conversion could not be performed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The specified A_BANK number does not exist.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when system number (MSS) was obtained.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in RMS960 system call.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Undefined interrupt command was received.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Job start condition is not defined.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in instruction prefetch queue operation.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Intermediate code is not defined.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Instruction prereading processing has not been completed normally.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in job data change.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The specified sequence number at job execution start is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The added area for interruption command is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
System number (MSS) for interruption command is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred at start of twin synchronous operation.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when SYNC specification was reset.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in occupation control group setting in MOTION section.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in path/trace control.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred when waiting for a completion of main system task (job) in SYNC specification.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An attempt was made to execute an instruction that could not be executed at line sequence execution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred while obtaining the instruction information.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An exceptional error occurred in job execution process.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Main processing command is incorrect in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Subprocessing command is incorrect in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Prereading processing has not been completed at job execution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
A_BANK conversion has not been completed.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
System number (MSS) is incorrect in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred in instruction prefetch queue operation in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An error occurred at IES switching in prereading processing.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
An attempt was made to execute an instruction that could not be executed in sub sequence(H) task
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
When PSTRIG instruction was executed, there was not PLCSTPON instruction or PLCSTPOF instruction.
Remedy:
(1) Reset the alarm.
(2) Check whether PLCSTPON instruction and PLCSTPOF instruction is registered. When unregistered, register PLCSTPON instruction and PLCSTPOF instruction.
Description:
When PSTRIG instruction was executed, P-PLC instruction had not been executed.
Remedy:
(1) Reset the alarm.
(2) Check whether P-PLC instruction is registered. When unregistered, register P-PLC instruction.
(3) When PSTRIG instruction is executed, check P-PLC instruction is whether it has been executed. If it is not running, please run PSTRIG instruction after P-PLC instruction execution.
Description:
The number of PSTRIG instruction exceeds the limit in the PointPLC program.
Remedy:
(1) Reset the alarm.
(2) please reduce the number that can be set PSTRIG instruction.
Description:
Delay control was not completed.
Remedy:
(1) Reset the alarm.
(2) Please change the teaching to be able to delay control.
Description:
PSTRIG instruction execution result is err.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PSTRIG instruction execution result is err.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm is complicated, please check the contents and take a measure.
Description:
PSTRIG instruction execution result is err.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PSTRIG instruction execution result is err.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
PSTRIG instruction execution result is err.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm is complicated, please check the contents and take a measure.
Description:
PSTRIG instruction execution result is err.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The new PSTRIG was performed during PSTRIG execution.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Control group
Remedy:
Check the following settings.
Description:
Sub Code: Control group
Remedy:
Check the following settings.
Description:
Device name or IP address has not been set to CP1616 board connected with 1st PCI connector.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please carry out the following according to a manual.
Set the device name and IP address to CP1616 board by using TIA Portal (setting tool by SIEMENS).
Download the project file.
Description:
Device name or IP address has not been set to CP1616 board connected with 2nd PCI connector.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, please carry out the following according to a manual.
Set the device name and IP address to CP1616 board by using TIA Portal (setting tool by SIEMENS).
Download the project file.
Description:
Firmware version of CP1616 board connected with 1st PCI connector and driver software version does not match.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the CP1616 board.
Description:
Firmware version of CP1616 board connected with 2nd PCI connector and driver software version does not match.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, replace the CP1616 board.
Description:
Task ID error
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
MSS ID error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
JOB handle error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
RMS error
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Job type is not SYSTEM JOB(CYCLIC/HIGH).
Remedy:
Change the job type to “SYSTEM JOB(CYCLIC/HIGH)”.
Description:
The intermediate code of the instruction that is to be executed is incorrect.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The instruction cannot be executed in the SYSTEM JOB(CYCLIC/HIGH).
Remedy:
Delete the instruction in which alarm occurred, because the instruction cannot be executed in the SYSTEM JOB(CYCLIC/HIGH).
Description:
The reinterpretation of the instruction was ordered when executing the instruction.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The SYSTEM JOB(CYCLIC/HIGH) was going to branch to the other job.
Remedy:
Delete the instruction in which alarm occurred, because The SYSTEM JOB(CYCLIC/HIGH) cannot branch to the other job.
Description:
The execution number of SYSTEM JOB(CYCLIC/HIGH) exceeded a limitation.
Remedy:
Correct the job under the current limitation of execution number, because SYSTEM JOB(CYCLIC/HIGH) can no longer be executed.
Description:
The execution of SYSTEM JOB(CYCLIC/HIGH) was not finished within a time limit.
Remedy:
Reduce the number of items in the SYSTEM JOB(CYCLIC/HIGH).
Description:
The SYSTEM JOB(CYCLIC/HIGH) was executed in the system being executed already.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
The execution number of items in the SYSTEM JOB(CYCLIC/HIGH) exceeded a limitation.
Remedy:
Reduce the number of items in the SYSTEM JOB(CYCLIC/HIGH) within the limit number(Initial setting is 300).
Description:
The meaning of each sub code is as follows:
CPU1 1:SFRON1
CPU1 2:SFRON2
CPU1 3:SFRON3
CPU1 4:SFRON4
CPU2 1:SFRON1 CPU2 2:SFRON2 CPU2 3:SFRON3 CPU2 4:SFRON4
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The meaning of each sub code is as follows:
CPU1 1:STO1
CPU1 2:STO2
CPU1 3:STO3
CPU1 4:STO4
CPU2 1:STO1 CPU2 2:STO2 CPU2 3:STO3 CPU2 4:STO4
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board.
In a system where a plurality of ASF01 boards are connected, replace the board, which is connected to the signal on which the alarm occurred.
Description:
The meaning of each sub code is as follows:
CPU1 1:GSOUT1
CPU1 2:GSOUT2
CPU2 1:GSOUT1 CPU2 2:GSOUT2
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The meaning of each sub code is as follows:
D01:XOUT01
D02:XOUT02
D03:XOUT03
D04:XOUT04
D05:XOUT05
D06:XOUT06
D07:XOUT07
D08:XOUT08
D09:XOUT09
D10:XOUT10
D11:XOUT11
D12:XOUT12
D13:XOUT13
D14:XOUT14
D15:XOUT15
D16:XOUT16
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The meaning of each sub code is as follows:
CPU1 1:SFRON1
CPU1 2:SFRON2
CPU1 3:SFRON3
CPU1 4:SFRON4
CPU2 1:SFRON1 CPU2 2:SFRON2 CPU2 3:SFRON3 CPU2 4:SFRON4
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The meaning of each sub code is as follows:
CPU1 1:STO1
CPU1 2:STO2
CPU1 3:STO3
CPU1 4:STO4
CPU2 1:STO1 CPU2 2:STO2 CPU2 3:STO3 CPU2 4:STO4
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the ASF01 board.
In a system where a plurality of ASF01 boards are connected, replace the board, which is connected to the signal on which the alarm occurred.
Description:
The meaning of each sub code is as follows:
CPU1 1:GSOUT1
CPU1 2:GSOUT2
CPU2 1:GSOUT1 CPU2 2:GSOUT2
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
The meaning of each sub code is as follows:
D01:XOUT01
D02:XOUT02
D03:XOUT03
D04:XOUT04
D05:XOUT05
D06:XOUT06
D07:XOUT07
D08:XOUT08
D09:XOUT09
D10:XOUT10
D11:XOUT11
D12:XOUT12
D13:XOUT13
D14:XOUT14
D15:XOUT15
D16:XOUT16
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Subcode is the signal number that detected error.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Subcode is the signal number that detected error.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
reference user frame not set
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
multiple reference user frame
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Incorrect control group designation
Remedy:
(1) Reset the alarm.
(2) Check the following settings.
Description:
Timing delay control was impossible
Remedy:
Check the following settings.
Description:
Timing exchange control was impossible
Remedy:
Please review a job so that an prohibited instruction does not enter between control object steps.
Description:
The message which was sent the last time has not been received.
Remedy:
Turn the power OFF then back ON.
Description:
The message which was sent when the NEXT/BACK/TEST operation was executed.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, check the following settings.
Description:
The message that was sent when the job was started.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, check the following settings.
Description:
The message which was sent from the pendant application.
Remedy:
(1) Turn the power OFF then back ON.
(2) If the alarm occurs again, check the following settings.
Description:
TAG could not be executed on JUMP instruction in the PointPLC program.
Remedy:
(1) Reset the alarm.
(2) Delete the TAG of the JUMP instruction which cannot be executed in the PointPLC program.
Description:
JUMP instruction or LABEL is wrong in the PointPLC program.
Remedy:
(1) Reset the alarm.
(2) Modify the JUMP instruction or LABEL in the PointPLC program.
JUMP destination in the PointPLC program will need to be set in the PointPLC program.
JUMP destination outside of PointPLC program will need to be set outside PointPLC program.
Description:
TAG could not be executed on CLEAR instruction in the PointPLC program.
Remedy:
(1) Reset the alarm.
(2) Delete the TAG of the CLEAR instruction which cannot be executed in the PointPLC program.
Description:
TAG could not be executed on CALL instruction in the PointPLC program.
Remedy:
(1) Reset the alarm.
(2) Delete the TAG of the CALL instruction which cannot be executed in the PointPLC program.
Description:
Local variable is used in the PointPLC program.
Remedy:
(1) Reset the alarm.
(2) Modify the instruction that uses Local variable in the PointPLC program.
Description:
Adjustment setting is exceeds the control area of the advance or delay control.
Remedy:
Correct the job so that adjustment setting is within the control area.
Description:
Timing advance control was impossible.
Remedy:
Correct the job so that it does not across the instructions that can not be advance control.
Description:
Timing delay control was impossible.
Remedy:
Correct the job so that it does not across the instructions that can not be delay control.
Description:
Undefined function
Description:
Multiple execution error
Description:
Parameter data type error
Description:
Function execution timeout
Description:
Variable type error for return value
Description:
String pool overflow
Description:
An attempt was made to move the group that is in use in MotoPlus function or Collaborative Operation function.
Remedy:
When using the automatic measurement of the tool load and the center of gravity, disable the collaborative operation before performing this function.
Content:
Illegal command data (parameter) is received from MOTION section.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
An optional function was commanded to be executed while another optional function was in execution.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The request to change standardization time was sent without permission.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The motor instruction standardization time is out of the allowable range.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The KP parameter input value is out of the allowable range.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
No processing corresponds to the command code sent from MOTION section.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
An attempt was made to turn ON the servo while the encoder was not ready.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The request to turn ON the servo power supply again was sent to an axis where the servo’s power was already ON.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The servo ON command was executed while the encoder was in alarm status.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the settings for jobs.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Check the settings for jobs.
(2) If this alarm occurs after the servo power cycling during work handling process under the condition where the Handling motion continue function is activated (S2C691=1), review the threshold value (S1CxG1080 - ) as necessary.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the settings for jobs.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the settings for jobs.
Content:
The difference value of the encoder exceeded the threshold value.
Remedy:
(1) Reset the alarm
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
[Robot axis]
Content:
An error occurred in real-time data transmission of SVSPOT Executing bit sent from MOTION.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The illegal data are stored in the averaging buffer. (The lowest digit shows the axis No.)
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The sum value in the averaging buffer is incorrect. (The lowest digit shows the axis No.)
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
The “empty” status of averaging buffer is incorrect. (The lowest digit shows the axis No.)
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
Overload detected parameter( a high resolution) was set to “0”, though overload-related parameter flag is ON.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Content:
An uncontrolled axis was specified at group change instruction execution.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the settings for jobs.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Content:
When the rating current and maximum current is zero, zero is set for the parameter of the rating current and the maximum current (high resolution).
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Step end stopping timeout of Positioning(distance specification) was detected.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN in maintenance mode, and then contact your Yaskawa representative about occurrence status (operating procedure).
Description:
PL control is not allowed when Positioning(distance specification) is enabled.
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN in maintenance mode, and then contact your Yaskawa representative about occurrence status (operating procedure).
Description:
Arithmetic error occurred when calculating consideration of servo delay for the Positioning(distance specification).
Remedy:
(1) Reset the alarm, and then try again.
(2) If the alarm occurs again, save the CMOS.BIN in maintenance mode, and then contact your Yaskawa representative about occurrence status (operating procedure).
Description:
Sub Code: Signifies the converter in which the alarm occurred
Remedy:
Modify the primary breaker power frequency to the frequency specified for the power supply on the rated label on the door of the controller.
Description:
Sub Code: Signifies the converter in which the alarm occurred
Remedy:
Confirm the phase sequence of the primary power supply connected to the breaker.
Description:
Sub Code: Signifies the converter in which the alarm occurred
Remedy:
Modify the primary breaker voltage to the voltage specified for the power supply on the rated label on the door of the controller.
Description:
Sub Code: Signifies the converter in which the alarm occurred
Remedy:
Check the primary voltage for the converter.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Confirm the following settings;
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, save the CMOS.BIN, and then contact your YASKAWA representative about occurrence status (operating procedure).
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the following settings.
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
Check the following settings.
Description:
Universal input/output 1 between SDCA01 boards is broken.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Universal output 1for SV#1 (SV#2) is inconsistent with Universal input 1 for SV#2(SV#1).
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Universal output 1for SV#1 (SV#2) is inconsistent with Universal input 1 for SV#2(SV#1).
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Universal input/output 2 between SDCA01 boards is broken or its connector (CN204) is disconnected.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Universal output 2 for SV#1 (SV#2) is inconsistent with Universal input 2 for SV#2(SV#1).
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Description:
Universal output 2 for SV#1 (SV#2) is inconsistent with Universal input 2 for SV#2(SV#1).
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the connection and inserting state of the following cables and connectors.
Content:
The manipulator exceeded its motion limit (pulse limit) in the negative (-) direction and the positive (+) direction in the motion target position.
Remedy:
Check the position setting for the step (move instruction) where the alarm occurred.
Content:
The manipulator exceeded its motion limit (mechanical limit) in the negative (-) and the positive (+) direction at the motion target point.
Remedy:
Check the position setting for the step (move instruction) where the alarm occurred.
Content:
The manipulator link was interfered with the motion target position.
Remedy:
Check the position setting for the step (move instruction) where the alarm occurred.
Content:
The manipulator link was interfered with the motion target position.
Remedy:
Check the position setting for the step (move instruction) where the alarm occurred.
Content:
The manipulator link was interfered with the motion target position.
Remedy:
Check the position setting for the step (move instruction) where the alarm occurred.
Content:
An error occurred when teach line cord jog move was in execution.
Remedy:
Correct the attitude of the tool and the ground are out of vertical, and execute teach line cord jog move.
Content:
An error occurred when teach line cord jog move was in execution.
Remedy:
Execute FWD/BWD/TEST RUN operation, and execute teach line cord jog move.
Description:
IMPOSSIBLE MOTION(Y direction)
Remedy:
Correct the teaching positions so that the attitude of the tool and the ground are out of vertical.
Description:
Shifted position data could not be converted.
Remedy:
The manipulator cannot move to the target shift position. Change shift volume or modify the teaching position.
Description:
Failed to move to the shifted position.
Remedy:
The manipulator cannot move to the shifted position. Correct the teaching positions so that the attitude of the tool and the ground are out of vertical.
Description:
Failed to pass through the shifted position.
Remedy:
The manipulator cannot pass through to the shifted position. Change the teaching position.
Description:
Direction of travel error
Remedy:
The manipulator cannot pass through to the direction of travel. Change the teaching position.
Description:
Shift start interval same position error
Remedy:
For shift start interval is same position, it can not shift. Change the teaching position.
Description:
Shift start interval shortage error
Remedy:
For shift start interval is short, it can not shift. Change the teaching position.
Description:
PREFLOW not executed
Remedy:
(1) When executing weld line coordinate shift operation, start the JOB with one step before ARCON instruction.
(2) When teaching the JOB for weldline coordinate shift operation, set the ARCON instruction in the JOB in which the weld line coordinate shift operation is to be performed. (Don’t set ARCON instruction in the JOB which is target for CALL instruction without setting any weld start teaching point. )
To use ARCON instruction without weld start point in the CALL destination JOB, disable the weld line coordinated shift function in the weld start condition file.
Description:
Sub Code: Control group
Remedy:
Please do not take effect safety of the speed limit by the functional safety during the interval of ARCON.
Description:
Sub Code: Control group
Remedy:
Check the following settings.
Description:
The procedure of the accessing to I/O module which is connected with 1st PCI connector did not finish in the defined period.
Remedy:
Check the following settings.
Description:
The procedure of the accessing to I/O module which is connected with 2nd PCI connector did not finish in the defined period.
Remedy:
Check the following settings.
Description:
The procedure of the accessing to I/O module which is connected with 3rd PCI connector did not finish in the defined period.
Remedy:
Check the following settings.
Description:
The procedure of the accessing to I/O module which is connected with 4th PCI connector did not finish in the defined period.
Remedy:
Check the following settings.
Description:
Sub Code: Signifies the axis in which the alarm occurred.
Remedy:
Try (1) if using the functional safety function.
Try (2) if you are not using the functional safety function, and the alarm occurs after replacing the robot, the controller or loading CMOS.BIN.
Try (3) if you are not using the functional safety function, and this alarm occurs after replacing the motor.
(1) In SAFETY MODE, calibrate the home position on the “HOME POSITION” window.
Then, perform “READBACK” and “WRITE”.
(2) In the MANAGEMENT MODE, select “CLEAR ROBOT DATA” under menu “DATA” on the “HOME POSITION” window, then clear home position data. Turn the power OFF then back ON.
(3) In the MANAGEMENT MODE, select “HOME POSITION” window and press the function menu “DATA” to select “RECORD TO ROBOT” which appears only when an alarm occurs.
Description:
Sub Code: Signifies the axis in which the alarm occurred.
Remedy:
Check the primary power supply voltage in converter.
Description:
Sub Code: Signifies the axis in which the alarm occurred.
Remedy:
Check the primary power supply voltage in converter.
Description:
Sub Code: Signifies the axis in which the alarm occurred.
Remedy:
Check the following settings;
Description:
Sub Code: Signifies the axis in which the alarm occurred.
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the converter.
Description:
A CRC mismatch was detected in the RC parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the SD parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the RO parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the SC parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the CIO parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the FD parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the AP parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the RS parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the SE parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the SV parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the SVM parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the AMC parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the SVP parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the MF parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the SVS parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the SVC parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the RC parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
A CRC mismatch was detected in the RC parameter.
Remedy:
(1) Reset the alarm, and then try again.
(2) Check whether the data which is going to load is surely saved as data of functional safety.
Description:
If the sub-code is 1nxx,the following is shown:
A feedback diagnosis error in ASF01 board number n, target signal xx(following)
00:BON
01:MCON
02-05:HWBB1-HWBB4
06-07:GSOUT1-GSOUT2
08-11:SFRON1-SFRON4
12-27:XOUT01-XOUT16
If the sub-code is 200n, the following is shown:
ASU03 unit connection error in unit number n.
If the sub-code is 210n, the following is shown:
ASF02 board connection error in board number n.
If the sub-code is 210n, the following is shown:
ASU03 unit connection error in unit number n.
If the sub-code is 22nn, the following is shown:
ASU03 unit connection error in unit number nn(bit).
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, check the following:
Description:
Sub Code: Signifies the axis in which the alarm occurred
Remedy:
(1) Reset the alarm.
(2) If the alarm occurs again, replace the encoder.