Overview of the YRC1000micro robot software releases which are relevant for MotoLogix.
This list reflects the software releases by YEU (Yaskawa Europe GmbH).
Releases and changes which are not relevant for MotoLogix are not listed here.
Releases
YBS3.04
07-02-2023
- Allow on-the-fly resetting of measured collision detection torques.
Requires parameter
S2C1704=1
.
YBS3.02
19-12-2022
- Allow on-the-fly switching of collision detection levels.
Requires parameter
S2C1703=1
. - Fix for
MLxRobotGetProperties
not returning correct axis limits.
YBS3.01
05-09-2022
- Adds
EtherCAT
support for theCIFX 50E-RE
fieldbus board. Due to packet size restrictions this combination cannot be used for MotoLogix. - Adds servofloat support for scara robots.
YBS2.54
03-05-2022
- Adds support for new fieldbus board
CIFX 50E-RE
. This PCIe board can handle many fieldbus protocols. In this first step it supportsPROFINET
andVARAN
fieldbus. - Adds a setting to adjust the distance of the automatic pull-back motion.
This motion is initiated immediately after a collision detection.
Set the distance in parameter
S1CxG353
(inmm
).
YBS2.53
07-04-2022
- Fix for slower-than-expected speed when using
MLxRobotJogAxes
.
YBS2.49
08-10-2021
- Adds support for Circular motion.
YBS2.48
01-07-2021
- Improvement for SCARA manipulators.
YBS2.46
14-04-2021
- Adds support for Tool calibration.
- Fix for conveyor tracking using SCARA manipulators.
- Fix for interference zone on rotated user frames.
YBS2.45
10-02-2021
- Adds support for Search motion.
- Adds support for Collision detection.
- Adds support for ServoFloat.
- Adds support for reading FSU CRC and timestamps from the controller.
YBS2.43
11-09-2020
- Adds actual TCP speed to the data packet:
MLX[].HMIFeedbackData.CurrentRobotTCPPosition[7]
. Requires parameterS2C1702=1
. - Adds support for Free Curve.
- Adds blending between PtP and linear motions.
Requires parameter
S2C1586=1
. - Adds
keyswitch=remote
signal to the data packet:MLX[].InternalData.ReadPacket.signals.RESERVED3
. - Fix for setting absolute data using
MLxRobotSetHomeOffsets
. - Improvement for conveyor tracking.
YBS2.40
14-05-2020
- Adds support for Collision detection.
- Adds support for Limit release.
- Adds support for Brake release.
YBS2.10.10
21-03-2019
- Fix for speed override.
YBS1.34
05-11-2018
- Adds support for the VMAX speed setting.
Upgrade process
If you feel your system needs to be upgraded please contact YEU.
In certain cases it might be possible to do the upgrade yourself (saving time and costs of a service visit). This is judged by YEU and depends on the manipulator type, version jump and customer experience.
As new software releases often come with new parameter settings, it still
requires some changes by YEU. This is done by exchanging the
ALL.PRM
file by
email.If YEU decided you can perform the upgrade by yourself the following process applies:
Read more...
1) Warning
Upgrading/downgrading of controller- or pendant software may only be
executed by experts. Any mistake can lead to a bricked system!
2) Preparation
- [Customer] Insert a USB stick in the pendant.
- [Customer] Save a system backup (
CMOS.BIN
):
EX. MEMORY » SAVE » SYSTEM BACKUP (CMOS.BIN) - [Customer] Save the
PANELBOX.LOG
file:
EX. MEMORY » SAVE » SYSTEM DATA » CONTROLLER INFORMATION - [Customer] Zip these two files and send it to YEU by email.
- [YEU] Send the following files by file share:
- New system software.
- Current system software.
- Upgrade manual for this controller.
3) Upgrade controller system software
The following steps apply for both upgrading and downgrading.
For more detailed instructions on the following steps please see the upgrade
manual.
- [Customer] Prepare a USB stick with the new software.
- [Customer] Insert the USB stick in the pendant.
- [Customer] Update the controller system software:
Restart while pressing interlock + 8 + select - [Customer] Start the upgrade process and wait until fully completed.
- [Customer] Restart in normal mode.
- [Customer] Check if no alarms and robot working normally.
4) Upgrade pendant software (optional)
The pendant software upgrade usually not necessary. YEU will instruct
if this step is required for your system.
- [Customer] Update the pendant software:
Restart while pressing 2 + 8 + high speed - [Customer] Start the upgrade process and wait until fully completed.
- [Customer] Restart in normal mode.
- [Customer] Check if no alarms and robot working normally.
5) Update parameter settings
- [Customer] Save the
ALL.PRM
file:
EX. MEMORY » SAVE » PARAMETER » BATCH PARAMETER - [Customer] Remove the USB stick from the pendant.
- [Customer] Send this file to YEU by email.
- [YEU] Adjust
ALL.PRM
for the new system software. - [YEU] Send this file to the customer by email.
- [Customer] Copy the file to a USB stick.
- [Customer] Insert the USB stick in the pendant.
- [Customer] Load the
ALL.PRM
in normal mode:
EX. MEMORY » LOAD » PARAMETER » BATCH PARAMETER - [Customer] Restart in normal mode.
- [Customer] Check if no alarms and robot working normally.
Reverting
The current system software and the
CMOS.BIN
are the bits you need to revert
to the original situation.